Skip to main content
Sign Out

Welcome to Dell

My Account
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Create and access a list of your products
Sign In Create an Account Premier Sign In Partner Program Sign In
Contact Us

Your Dell.com Carts

Dell SmartFabric OS10 User Guide Release 10.5.4

PDF

Example - Configure IPv6 PIM bootstrap

The following topology diagram describes the IPv6 PIM bootstrap configuration:

Perform the following steps for configuring PIM bootstrap:

  • Establish IPv6 PIM neighborship between routers (FHR, RP, and LHR nodes).
  • Configure uUnicast IPv6 route reachability using OSPFv3 for the static RP and multicast source addresses.
  • Configure BSR and RP-candidate for electing RP in and IPv6 network.
  • Learn MLDv1 groups and multicast streams and verify RPT and SPT path.

Establish IPv6 PIM neighbor-ship between routers (FHR, RP, and LHR nodes)

Enable IPv6 multicast forwarding and configured IPv6 PIM neighbor-ship between devices. 
FHR# show ipv6 pim neighbor
Neighbor Address Interface         Uptime/Expires     Ver  DR Priority / Mode
-------------------------------------------------------------------------------------------------------------
20:1::2          ethernet1/1/27:1  00:01:09/00:01:36  v2   1 / DR S
FHR#
Following are the FHR device configurations: 
FHR# configure terminal
FHR(config)# ipv6 multicast-routing
FHR(config)# interface ethernet 1/1/27:1
FHR(conf-if-eth1/1/27:1)# no switchport
FHR(conf-if-eth1/1/27:1)# ipv6 address 20:1::1/64
FHR(conf-if-eth1/1/27:1)# ipv6 pim sparse-mode
FHR(conf-if-eth1/1/27:1)# exit

FHR(config)# interface ethernet 1/1/18:1
FHR(conf-if-eth1/1/18:1)# no switchport
FHR(conf-if-eth1/1/18:1)# ipv6 address 50:1::1/64
FHR(conf-if-eth1/1/18:1)# ipv6 pim sparse-mode
FHR(conf-if-eth1/1/18:1)# end
FHR#
Following are the RP device configurations: 
RP# configure terminal
RP(config)# ipv6 multicast-routing
RP(config)# interface ethernet 1/1/27:1
RP(conf-if-eth1/1/27:1)# no switchport
RP(conf-if-eth1/1/27:1)# ipv6 address 20:1::2/64
RP(conf-if-eth1/1/27:1)# ipv6 pim sparse-mode
RP(conf-if-eth1/1/27:1)# exit

RP(config)# interface ethernet 1/1/26:1
RP(conf-if-eth1/1/26:1)# no switchport
RP(conf-if-eth1/1/26:1)# ipv6 address 21:1::2/64
RP(conf-if-eth1/1/26:1)# ipv6 pim sparse-mode
RP(conf-if-eth1/1/26:1)# exit
RP#
Following are LHR device configurations: 
LHR# configure terminal
LHR(config)# ipv6 multicast-routing
LHR(config)# interface ethernet 1/1/26:1
LHR(conf-if-eth1/1/26:1)# no switchport
LHR(conf-if-eth1/1/26:1)# ipv6 address 21:1::1/64
LHR(conf-if-eth1/1/26:1)# ipv6 pim sparse-mode
LHR(conf-if-eth1/1/26:1)# exit

LHR(config)# interface ethernet 1/1/27:1
LHR(conf-if-eth1/1/27:1)# no switchport
LHR(conf-if-eth1/1/27:1)# ipv6 address 61:1::1/64
LHR(conf-if-eth1/1/27:1)# ipv6 pim sparse-mode
LHR(conf-if-eth1/1/27:1)# end
LHR#

Configure unicast IPv6 route reachability using OSPFv3 for the static RP and multicast source addresses

Configure OSPFv3 for IPv6 unicast route reachability and configure multicast sources on FHR and host-connected interfaces on LHR device.

Following are the FHR device configurations: 
FHR# configure terminal
FHR(config)# interface ethernet 1/1/27:1
FHR(conf-if-eth1/1/27:1)# ipv6 ospf 1 area 0
FHR(conf-if-eth1/1/27:1)# exit
FHR#(config)# router ospfv3 1
FHR(config-router-ospfv3-1)# end
FHR#
FHR# configure terminal
FHR(config)# interface ethernet 1/1/18:1
FHR(conf-if-eth1/1/18:1)# ipv6 ospf 1 area 0
FHR(conf-if-eth1/1/18:1)# exit
FHR(config)# end
FHR#
Following are the RP device configurations: 
RP# configure terminal
RP(config)# interface ethernet 1/1/27:1
RP(conf-if-eth1/1/27:1)# ipv6 ospf 1 area 0
RP(conf-if-eth1/1/27:1)# exit
RP#(config)# router ospfv3 1
RP(config-router-ospfv3-1)# end
RP#
RP# configure terminal
RP(config)# interface ethernet 1/1/26:1
RP(conf-if-eth1/1/26:1)# ipv6 ospf 1 area 0
RP(conf-if-eth1/1/26:1)# exit
RP(config)# end
RP#
Following are the LHR device configurations: 
LHR# configure terminal
LHR(config)# interface ethernet 1/1/26:1
LHR(conf-if-eth1/1/26:1)# ipv6 ospf 1 area 0
LHR(conf-if-eth1/1/26:1)# exit
LHR#(config)# router ospfv3 1
LHR(config-router-ospfv3-1)# end
LHR#
LHR# configure terminal
LHR(config)# interface ethernet 1/1/27:1
LHR(conf-if-eth1/1/27:1)# ipv6 ospf 1 area 0
LHR(conf-if-eth1/1/27:1)# exit
LHR(config)# end
LHR#

Configure BSR and RP-candidate for electing RP in and IPv6 network

Configure dynamic RP using BSR. 
RP# conf
RP(config)# interface loopback 0
RP(conf-if-lo-0)# ip address 1.1.1.1/32
RP(conf-if-lo-0)# ipv6 address 11:1:1::1/128
RP(conf-if-lo-0)# ipv6 ospf 1 area 0
RP(conf-if-lo-0)# exit
RP(config)# 
RP(config)# ipv6 pim bsr-candidate loopback0
RP(config)# ipv6 pim rp-candidate loopback0 
RP(config)# end
RP#

RP# show ipv6 pim bsr-router

This system is the Bootstrap Router (v2)
BSR address: 11:1:1::1
BSR Priority: 64, Hash mask length: 126
Next bootstrap message in 00:00:53
This system is a candidate BSR
Candidate BSR address: 11:1:1::1, priority: 64, hash mask length: 126
Next Cand_RP_advertisement in 00:00:47
RP: 11:1:1::1(loopback0)
RP#
RP# show ipv6 pim rp mapping

Group(s) : 224.0.0.0/4
RP : 11:1:1::1, v2
Info source: 11:1:1::1, via bootstrap, priority 192
expires: 00:02:12
RP#

Learn MLDv1 groups and multicast streams and verify RPT and SPT path

Verify MLD group members, IPv6 PIM RPT and SPT entries. 
LHR#show ipv6 mld groups
Total Number of Groups: 1
MLD Connected Group Membership
Group Address Interface Mode Uptime Expires Last Reporter
fffe:ffff:225:1:1:: ethernet 1/1/27:1 MLDv1-Compat 00:01:58 00:01:59 fe80::200:47ff:fe22:1b2b
LHR#
LHR#show ipv6 pim rp
Group RP
fffe:ffff:225:1:1:: 11:1:1::1
LHR#
LHR#show ipv6 pim tib

PIM Multicast Routing Table
Flags: S - Sparse, C - Connected, L - Local, P - Pruned,
F - Register flag, T - SPT-bit set, J - Join SPT,

Timers: Uptime/Expires
Interface state: Interface, next-Hop, State/Mode

(*, fffe:ffff:225:1:1::), uptime 00:01:27, expires 00:00:00,
RP: 11:1:1::1, flags: SCJ
Incoming interface: Ethernet 1/1/26:1, RPF neighbor fe80::3617:ebff:fe1f:6b82
Outgoing interface list:
    Ethernet 1/1/27:1 Forward/Sparse 00:01:27/Never

LHR#
LHR#show ipv6 pim mcache

IP Multicast Routing Table

(*, fffe:ffff:225:1:1::), uptime 00:02:17
Incoming interface: Ethernet 1/1/26:1
Outgoing interface list:
     Ethernet 1/1/27:1

LHR#

Rate this content

Accurate
Useful
Easy to understand
Was this article helpful?
0/3000 characters
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please provide ratings (1-5 stars).
  Please select whether the article was helpful or not.
  Comments cannot contain these special characters: <>()\