- Notes, cautions, and warnings
- VXLAN
- VXLAN concepts
- VXLAN as NVO solution
- Configure VXLAN
- L3 VXLAN route scaling
- DHCP relay on VTEPs
- View VXLAN configuration
- VXLAN MAC addresses
- Example: VXLAN with static VTEP
- Controller-provisioned VXLAN
- BGP EVPN for VXLAN
- BGP EVPN compared to static VXLAN
- VXLAN BGP EVPN operation
- Configure BGP EVPN for VXLAN
- BGP EVPN with VLT
- VXLAN BGP EVPN routing
- Example: VXLAN with BGP EVPN
- Example: VXLAN BGP EVPN — Multiple AS topology
- Example: VXLAN BGP EVPN — Centralized L3 gateway
- Example: VXLAN BGP EVPN — Border leaf gateway with asymmetric IRB
- Example: VXLAN BGP EVPN—Symmetric IRB
- Example - VXLAN BGP EVPN symmetric IRB with unnumbered BGP peering
- Example - Route leaking across VRFs in a VXLAN BGP EVPN symmetric IRB topology
- Example: Migrating from Asymmetric IRB to Symmetric IRB
- VXLAN MAC commands
- clear mac address-table dynamic nve remote-vtep
- clear mac address-table dynamic virtual-network
- show mac address-table count extended
- show mac address-table count nve
- show mac address-table count virtual-network
- show mac address-table extended
- show mac address-table nve
- show mac address-table virtual-network
- VXLAN BGP commands
- VXLAN commands
- hardware overlay-routing-profile
- interface virtual-network
- ip virtual-router address
- ip virtual-router mac-address
- member-interface
- nve
- remote-vtep
- show hardware overlay-routing-profile mode
- show interface virtual-network
- show nve remote-vtep
- show nve remote-vtep counters
- show nve vxlan-vni
- show virtual-network
- show virtual-network counters
- show virtual-network interface counters
- show virtual-network interface
- show virtual-network vlan
- show vlan (virtual network)
- source-interface loopback
- virtual-network
- virtual-network untagged-vlan
- vxlan-vni
- VXLAN EVPN commands
- Support resources
VXLAN and BGP EVPN Configuration Guide for Dell EMC SmartFabric OS10 Release 10.5.2
Specify the controller reachability information
In OS10 VTEP, the controller configuration command initializes a connection to an OVSDB-based controller.
OS10 supports only one controller connection at a time.
NOTE Currently, the only
supported OVSDB-based controller is NSX.
To configure an OVSDB
controller on the OS10 VTEP:- Enable VXLAN in CONFIGURATION mode.
OS10(config)# nve
- Changes the mode to CONFIGURATION-NVE-OVSDB from where you can configure
the controller parameters.
OS10(config-nve)# controller ovsdb
- Specify the IP address, OVSDB controller port, and SSL as a secure
connection protocol between the OS10 VTEP and the controller in CONFIGURATION-NVE-OVSDB
mode.
OS10(config-nve-ovsdb)# ip ip-address port port-number sslThe range of port-numberis from 0 to 65535. Configure the port-number as 6640 and the connection type as SSL.
- (Optional) Specify a time interval, in milliseconds (ms). This is
the duration the switch waits between the connection attempts to the
controller.
OS10(config-nve-ovsdb)# max-backoff intervalThe range is from 1000 to 180,000 ms. The default is 8000 ms.
OS10# configure terminal OS10(config)# nve OS10(config-nve)# controller ovsdb OS10(config-nve-ovsdb)# ip 10.11.66.110 port 6640 ssl
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\