This example shows a simple NSX controller and an hardware OS10 VTEP
deployed in VXLAN environment.
![NSX controller implementation](https://dl.dell.com/content/guides/public/html//vxlan-evpn-10-5-2_ug/images/GUID-A627D51F-84E2-4715-8D6A-991648C644BA-low.png)
To configure
an NSX controller-provisioned VXLAN:
- Configure the controller
and the interfaces to be managed by the controller, in the OS10 VTEPs
- Configure the NSX controller
in VMware vCenter. For more information about configuring the NSX
controller using the GUI, see the Configure and control
VXLAN from the VMware vCenter.
You must configure an OS10 VTEP with the controller
configuration so that the VTEP can communicate with the NSX controller.
The NSX controller handles configurations and control plane operations
in the VXLAN environment.
Verify the controller
configuration
To view controller-based information on the VTEP 1, use
the show nve controller command.
OS10# show nve controller
Management IP : 10.16.140.11/16
Gateway IP : 200.0.0.1
Max Backoff : 10000
Configured Controller : 10.16.140.181:6640 ssl (connected)
Controller Cluster
IP Port Protocol Connected State Max-Backoff
10.16.140.182 6640 ssl true ACTIVE 10000
10.16.140.183 6640 ssl true ACTIVE 10000
10.16.140.181 6640 ssl true ACTIVE 10000
NVE Controller Ports
ethernet1/1/54:3
To display the VNID, port members, source
interface, and remote VTEPs of the VXLAN, use the show virtual-network command.
OS10# show virtual-network
Codes: DP - MAC-learn Dataplane, CP - MAC-learn Controlplane, UUD - Unknown-Unicast-Drop
Virtual Network: 0
Members:
Virtual Network: 6000
Members:
VLAN 20: ethernet1/1/54:3
VxLAN Virtual Network Identifier: 6000
Source Interface: loopback1(200.0.0.1)
Remote-VTEPs (flood-list): 13.0.0.5(CP)
To view all the replicators and their status
in the VXLAN, use the show nve replicators command.
OS10# show nve replicators
Codes: * - Active Replicator
BFD Status:Disabled
Replicators State
-----------------------
13.0.0.5 Up
13.0.0.3 Up
13.0.0.2 Up
To view the remote VTEP status, use the show nve remote-vtep command.
OS10# show nve remote-vtep
IP Address: 13.0.0.2, State: up, Encap: VxLAN
VNI list: ,6000
IP Address: 13.0.0.3, State: up, Encap: VxLAN
VNI list: ,6000
IP Address: 13.0.0.5, State: up, Encap: VxLAN
VNI list: ,6000
IP Address: 202.0.0.1, State: up, Encap: Vxlan
VNI list: 6000
VTEP 2
OS10# show nve controller
Management IP : 10.16.140.13/16
Gateway IP : 202.0.0.1
Max Backoff : 10000
Configured Controller : 10.16.140.181:6640 ssl (connected)
Controller Cluster
IP Port Protocol Connected State Max-Backoff
10.16.140.182 6640 ssl true ACTIVE 10000
10.16.140.183 6640 ssl true ACTIVE 10000
10.16.140.181 6640 ssl true ACTIVE 10000
NVE Controller Ports
ethernet1/1/25:3
To display the VNID, port members, source
interface, and remote VTEPs of the VXLAN, use the show virtual-network command.
OS10# show virtual-network
Codes: DP - MAC-learn Dataplane, CP - MAC-learn Controlplane, UUD - Unknown-Unicast-Drop
Virtual Network: 0
Members:
Virtual Network: 6000
Members:
VLAN 20: ethernet1/1/25:3
VxLAN Virtual Network Identifier: 6000
Source Interface: loopback1(202.0.0.1)
Remote-VTEPs (flood-list): 13.0.0.5(CP)
To view all the replicators and their status
in the VXLAN, use the show nve replicators command.
OS10# show nve replicators
Codes: * - Active Replicator
BFD Status:Disabled
Replicators State
-----------------------
13.0.0.5 Up
13.0.0.3 Up
13.0.0.2 Up
To view the remote VTEP status, use the show nve remote-vtep command.
OS10# show nve remote-vtep
IP Address: 13.0.0.2, State: up, Encap: VxLAN
VNI list: ,6000
IP Address: 13.0.0.3, State: up, Encap: VxLAN
VNI list: ,6000
IP Address: 13.0.0.5, State: up, Encap: VxLAN
VNI list: ,6000
IP Adress: 200.0.0.1, State: up, Encap: Vxlan
VNI list: 6000