0
|
Success
|
1
|
Attempt to read write-only parameter.
|
2
|
Password cannot exceed 16 characters.
|
3
|
A BMC was either not detected or is not supported.
|
4
|
This username is already in use. Enter a unique username.
|
5
|
Access mode not supported.
|
6
|
Cannot return number of requested data bytes.
|
7
|
User ID 1 cannot be assigned a username.
|
8
|
Cannot execute duplicated request.
|
9
|
There was an error clearing the SEL.
|
10
|
Clear SEL cannot be accompanied with any other option.
|
11
|
racreset cannot be accompanied with any other option.
|
12
|
Cannot execute command. Command, or request parameter(s),
not supported in present state.
|
13
|
Command not supported on given channel.
|
14
|
The community string may only contain printable ASCII
characters.
|
15
|
Destination unavailable. Cannot deliver request to
selected destination.
|
16
|
Cannot execute command. Insufficient privilege level.
|
17
|
Command illegal for specified sensor or record type.
|
18
|
Invalid commstring value.
|
19
|
Hardware subsystem error. Invalid data field in Request.
|
20
|
Invalid destination IP address.
|
21
|
The GUID is invalid.
|
22
|
Invalid gateway.
|
23
|
Invalid hostname.
|
24
|
Invalid IP address.
|
25
|
Invalid DNS IP address.
|
26
|
Invalid sub net mask.
|
27
|
Invalid value for PEF. PEF value should be between
1 and 16.
|
28
|
Reservation Canceled or Invalid Reservation ID.
|
29
|
Invalid Time to live value.
|
30
|
Invalid VLANID value.
|
31
|
Invalid Command. Used to indicate an unrecognized or
unsupported command.
|
32
|
Command invalid for given LUN.
|
33
|
Load defaults cannot be accompanied with any other
option.
|
34
|
There was an error loading the defaults.
|
35
|
Node Busy. Command could not be processed because command
processing resources are temporarily unavailable.
|
36
|
Out of space. Command could not be completed because
of a lack of storage space required to execute the given command operation.
|
37
|
This parameter is not supported.
|
38
|
Parameter out of range. One or more parameters in the
data field of the Request are out of range.
|
39
|
The password may only contain printable ASCII characters.
|
40
|
Password test failed.
|
41
|
Requested data length invalid.
|
42
|
Requested data field length limit exceeded.
|
43
|
Requested Sensor, data, or record not present.
|
44
|
Request data truncated.
|
45
|
Command response could not be provided.
|
46
|
Command response could not be provided. BMC initialization
or initialization agent in progress.
|
47
|
Command response could not be provided. Device in firmware
update mode.
|
48
|
Command response could not be provided. SDR Repository
in update mode.
|
49
|
Cannot execute command, SEL erase in progress.
|
50
|
Attempt to set the 'set in progress' value when not
in the 'set in complete' state.
|
51
|
The SOL character ’accumulate interval’ is invalid.
|
52
|
The SOL character ’send threshold’ is invalid.
|
53
|
The SOL ’retry interval’ is invalid.
|
54
|
Command completed successfully.
|
55
|
Time-out while processing command. Response unavailable.
|
56
|
Unspecified error.
|
57
|
The password may only contain printable ASCII characters.
|
58
|
Username cannot exceed 16 characters.
|
59
|
Invalid VLANID value. Enter in ’dddd’ format.
|
60
|
Attempt to write read-only parameter.
|
61
|
BMC is busy.
|
62
|
Response data did not return successfully.
|
63
|
BMC time out error.
|
64
|
Option requires an argument.
|
65
|
The asset tag for this system is not available.
|
66
|
The asset tag cannot be more than 10 characters long.
|
67
|
The required BIOS interfaces cannot be found on this
system.
|
68
|
The BIOS version information is not available.
|
69
|
There is not enough free system memory to complete
the BIOS update.
|
70
|
The BIOS update file version is a different version
class (A00, X00) than the current system BIOS. Use the --force option
to use this BIOS image.
|
71
|
The BIOS update file version is older than the current
system bios. Use the --force option to use this BIOS image.
|
72
|
The BIOS update file version is identical to the current
system bios. Use the --force option to use this BIOS image.
|
73
|
The sequence list must be a comma-separated numerical
list of valid unique boot device numbers (ex: 2, 1, 3).
|
74
|
The sequence list must be a comma-separated list of
valid unique device names (ex: nic.emb.1, hdd.emb.1) or a comma-separated
numerical list of valid unique boot device numbers (ex: 2, 1, 3).
|
75
|
There was an error setting the sequence.
|
76
|
The list is not formatted correctly. See the help for
more details.
|
77
|
The size of returned buffer is larger than the size
of allocated buffer.
|
78
|
There was a problem getting the state byte.
|
79
|
The state byte is not available on this system.
|
80
|
There was a problem setting the state byte.
|
81
|
The state byte must be a value between 0 and 255 decimal.
|
82
|
The CPU information is not available.
|
83
|
The dependent option required for this subcommand is
missing in the command line.
|
84
|
Duplicate sub command has been entered.
|
85
|
The script file does contain not a valid DTK environment
script signature.
|
86
|
The format of the environment variable is incorrect.
|
87
|
The --envar option can only be used for a single option.
|
88
|
The --envar option can only be used for report operations.
|
89
|
The individual sub commands should be specified for
the -s option.
|
90
|
Getting external serial connector settings failed.
|
91
|
Setting external serial connector settings failed.
|
92
|
There was an error opening the file.
|
93
|
File does not have write permission.
|
94
|
The file contains invalid options.
|
95
|
The replication information does not match for this
system.
|
96
|
There can only be one section in the input file.
|
97
|
Bad ini file, the section cannot be found.
|
98
|
The format of the bios image file is incorrect.
|
99
|
Report operations and set operations must be separate.
|
100
|
Help is not available for the option.
|
101
|
The -x (--hex) option can only be used with -b or -r.
|
102
|
Input file not found.
|
103
|
Input file cannot be read.
|
104
|
Invalid argument for option.
|
105
|
Function table lookup error.
|
106
|
The machine ID was not found in the file.
|
107
|
The system memory information is not available.
|
108
|
Mode can only be used with the --pci option.
|
109
|
The device name or index must be present in the boot
order.
|
110
|
The output file could not be opened. Please make sure
the path exists and the media is not write protected.
|
111
|
Could not write to output file, disk may be full.
|
112
|
The current password must be supplied with a new password
using --oldsyspwd.
|
113
|
The current password must be supplied with a new password
using --oldsetuppwd.
|
114
|
The current password can only be supplied when setting
a new password.
|
115
|
Actions are not allowed for this filter. Only alerts
are allowed.
|
116
|
There was an error getting the option.
|
117
|
The option is not available or cannot be configured
through software.
|
118
|
There was an error setting the option.
|
119
|
The -n (--namefile) option can only be used with -
-pci.
|
120
|
The password may only contain alphanumeric characters.
|
121
|
The BIOS passwords have been disabled via jumper.
|
122
|
The password length must be between 1 and 32.
|
123
|
This password is locked and can only be unlocked by
the admin user.
|
124
|
There was an error setting the password.
|
125
|
The LCD string length must be between 1 and %s.
|
126
|
The LCD string may only contain alphanumeric characters.
|
127
|
There was an error setting the LCD string.
|
128
|
The second channel can only be set if the RAID controller
is set to RAID.
|
129
|
The set operation requires sub commands.
|
130
|
The service tag for this system is not available.
|
131
|
The system ID value is not available.
|
132
|
The system information string is not available.
|
133
|
A system error has occurred.
|
134
|
Usage error.
|
135
|
The uuid information is not present on this system
|
136
|
Version cannot be accompanied with any other option.
|
137
|
The self-identify blinker timer should be set to 0..255
second(s).
|
138
|
Encrypt key is too long.
|
139
|
Encrypt key is invalid, accepted characters are 0 to
9 or A to F.
|
140
|
Parameter has been temporarily disabled due to a dependency
on other settings.
|
141
|
The old password supplied is incorrect. The new password
will not be set. Please try again.
|
142
|
Cannot stat /etc/omreg.cfg file. Please ensure /etc/omreg.cfg
file is present and is valid for your environment. You can copy this
file from the DTK iso.
|
143
|
Getting nicselection settings failed.
|
144
|
HAPI Driver Load Error.
|
145
|
Filter action power reduction is only supported for
the system power warn/fail filters.
|
146
|
TPM/TCM Clear settings requires setup password.
|
147
|
There is currently no TPM/TCM Clear request pending.
|
148
|
Password is not required for retrieving the ’%s’ options.
|
149
|
Setup password is required for setting the ’%s’ options.
|
150
|
Invalid Password override.
|
151
|
Invalid TPM/TCM set option.
|
152
|
There was an error setting the TPM/TCM option.
|
153
|
There is no setup password installed on this system.
|
154
|
The setup password supplied is incorrect. Please try
again.
|
155
|
Profile should be custom for setting cpupowermode,
memorypowermode and fanmode.
|
156
|
There was an error setting the Power Option.
|
157
|
The power cap value entered is out of range. Please
try again.
|
158
|
The power cap value entered must be between 0 to 100
if unit is percent.
|
159
|
Invalid IPv6 address. The IPv6 address cannot be link-local
or multicast.
|
160
|
Invalid IPv6 address. The IPv6 address specified has
incorrect address format.
|
161
|
Invalid IPv6 address. The gateway address specified
has incorrect address format.
|
162
|
Invalid IPv6 address. The Primary DNS server address
specified has incorrect address format.
|
163
|
Invalid IPv6 address. The Secondary DNS server address
specified has incorrect address format.
|
164
|
Invalid IPv6 address. The gateway address specified
is invalid.
|
165
|
Invalid configuration. Attempting to apply IPv6 configuration
on a non supported platform.
|
166
|
Invalid IPv6 configuration. Attempt to set DNS server
address manually while DNS address source is set to auto.
|
167
|
Invalid IPv6 configuration. Attempt to set IPv6 address
manually while IPv6 address source is set to auto.
|
168
|
Invalid IPv6 configuration. Attempting to apply IPv6
configuration without loading IPv6 stack.
|
169
|
Invalid IPv4 configuration. Attempting to apply IPv4
configuration with IPv4 disabled.
|
170
|
Invalid IPv6 configuration. Ipv6 address cannot be
specified without specifying prefix-length.
|
171
|
Invalid IPv6 configuration. dnssrcv6 cannot be set
to auto when ipsrcv6 is set to manual.
|
172
|
Error while executing IPMI Set command.
|
173
|
Error while executing IPMI Get command.
|
174
|
Error during Trap Alert.
|
175
|
Unspecified error.
|
176
|
Getting LCD settings failed.
|
177
|
Invalid configuration. Attempting to set cap when capenable
is set to disable.
|
178
|
Invalid configuration. Attempting to set cap when hardware
does not support setting.
|
179
|
Invalid Configuration Option.
|
180
|
Cannot execute command. Parameter is illegal because
command sub-function has been disabled or is unavailable.
|
181
|
Failed to report the removable flash media redundancy
status.
|
182
|
Failed to report the Internal SD Module status.
|
183
|
Error locating the Virtual Media Key on the Modular
system.
|
184
|
Error in setting the redundancy option for the Internal
SD Modules.
|
185
|
Error in retrieving the redundancy option for the Internal
SD Modules.
|
186
|
Error in setting the redundancy option on Modular systems
for the Internal SD Modules.
|
187
|
Error in retrieving the vFlash option.
|
188
|
Error in setting the vFlash option.
|
189
|
The set operation failed due to dependency.
|
190
|
The set operation failed because attribute is forced
to a value.
|
191
|
Cannot disable this OrderedList’s entries.
|
192
|
The set operation failed because system is busy now
. Try again later.
|
193
|
New value for the token not valid.
|
194
|
Token not found.
|
195
|
The set operation failed because System Services and/or
CSIOR disabled.
|
196
|
The set operation failed due to pending System Password
changes.
|
197
|
The set operation failed due to Password verification
failure.
|
198
|
The set operation failed due to previously scheduled
job.
|
199
|
The set operation failed because attribute is suppressed.
|
200
|
The set operation failed due to Generic failure.
|
201
|
XML path context creation failed.
|
202
|
Unable to parse XML.
|
203
|
Unable to connect data manager.
|
204
|
'root' privileges required to execute this application.
|
205
|
Invalid alert destination.
|
206
|
The set operation failed due to unspecified error.
|
207
|
Incorrect syntax for help. For more information about
a particular command, use the option '-h or --help' followed by the
command name. Example: %s -h --asset
|