- Notes, cautions, and warnings
- Views of Latitude 5350/Latitude 5350 2-in-1
- Set up your Latitude 5350/Latitude 5350 2-in-1
- Specifications of Latitude 5350/Latitude 5350 2-in-1
- Dimensions and weight
- Processor
- Chipset
- Operating system
- Memory
- External ports
- Internal slots
- Wireless module
- WWAN module
- Audio
- Storage
- Keyboard
- Camera
- Touchpad
- Power adapter
- Battery
- Display
- Fingerprint reader (optional)
- Sensor
- GPU—Integrated
- External display support
- Hardware security
- Smart-card reader
- Operating and storage environment
- Dell support policy
- ComfortView Plus
- Using the privacy shutter
- Dell Optimizer
- Working inside your computer
- Removing and installing Customer Replaceable Units (CRUs)
- Removing and installing Field Replaceable Units (FRUs)
- Software
- BIOS Setup
- Troubleshooting
- Handling swollen rechargeable Li-ion batteries
- Locate the Service Tag or Express Service Code of your Dell computer
- Dell SupportAssist Pre-boot System Performance Check diagnostics
- Built-in self-test (BIST)
- System-diagnostic lights
- Recovering the operating system
- Real-Time Clock (RTC Reset)
- Backup media and recovery options
- Wi-Fi power cycle
- Drain residual flea power (perform hard reset)
- Getting help and contacting Dell
Latitude 5350/Latitude 5350 2-in-1 Owner's Manual
System-diagnostic lights
This section lists the system-diagnostic lights of your Latitude 5350/Latitude 5350 2-in-1.
Power and battery-status light
The power and battery status light indicates the power and battery status of the computer. These are the power states:
Solid white: Power adapter is connected and the battery is charging.
Sold amber: Battery charge is low or critical.
Off: Battery is fully charged.
- Power adapter is connected, and the battery is fully charged.
- Computer is running on battery, and the battery has more than 5% charge.
- Computer is in sleep state, hibernation, or turned off.
The power and battery-status light may blink amber or white according to pre-defined "beep codes" indicating various failures.
For example, the power and battery-status light blinks amber two times followed by a pause, and then blinks white three times followed by a pause. This 2,3 pattern continues until the computer is turned off, indicating no memory or RAM is detected.
| Blinking pattern | Problem description | |
|---|---|---|
| Amber | White | |
| 1 | 1 | TPM detection failure |
| 1 | 2 | Unrecoverable SPI Flash Failure |
| 1 | 5 | EC unable to program i-Fuse |
| 1 | 6 | Generic catch-all for ungraceful EC code flow errors |
| 2 | 1 | CPU failure |
| 2 | 2 | System board failure (included BIOS corruption or ROM error) |
| 2 | 3 | No memory or RAM detected |
| 2 | 4 | Memory or RAM failure |
| 2 | 5 | Invalid memory installed |
| 2 | 6 | System board or Chipset Error |
| 2 | 7 | LCD failure (SBIOS message) |
| 2 | 8 | LCD failure (EC detection of power rail failure) |
| 3 | 1 | CMOS battery failure |
| 3 | 2 | PCI or Video card or chip failure |
| 3 | 3 | BIOS Recovery image not found |
| 3 | 4 | BIOS Recovery image found but invalid |
| 3 | 5 | Power rail failure |
| 3 | 6 | Flash corruption is detected by SBIOS. |
| 3 | 7 | Timeout waiting on ME to reply to HECI message. |
NOTE:Blinking 3-3-3 LEDs on Lock LED (Caps-Lock or Num-Lock), Power button LED (without Fingerprint reader), and Diagnostic LED indicates failure to provide input during LCD panel test on Dell SupportAssist Pre-boot System Performance Check diagnostics.
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please provide ratings (1-5 stars).
Please select whether the article was helpful or not.
Comments cannot contain these special characters: <>()\