BatteryStatus
|
Description of the charge status of the Battery.
Possible values are:
- 1 = Other
- 2 = Unknown
- 3 = Fully Charged
- 4 = Low
- 5 = Critical
- 6 = Charging
- 7 = Charging and High
- 8 = Charging and Low
- 9 = Charging and Critical
- 10 = Undefined
- 11 = Partially Charged
- 12 = Learning
- 13 = Overcharged
Values such as
Fully Charged (value =
3) or
Partially Charged (value =
11) can be specified. The value,
10, is not valid in the CIM Schema because in DMI it represents
that no battery is installed. In this case, this object should not
be instantiated.
|
ChargingStatus
|
This property defines status information about the AC line
in the notebook.
Possible values are:
- 1 = Other
- 2 = Unknown
- 3 = Off- Line
- 4 = On-Line
- 5 = On Backup Power
|
Chemistry
|
An enumeration that describes the chemistry of the Battery.
- 1 = Other
- 2 = Unknown
- 3 = Lead Acid
- 4 = Nickel Cadmium
- 5 = Nickel Metal Hydride
- 6 = Lithium-ion
- 7 = Zinc air
- 8 = Lithium Polymer
|
CreationClassName
|
Indicates the name of the class or the subclass used in
the creation of an instance. When used with the other key properties
of this class, this property allows all instances of this class and
its subclasses to be uniquely identified.
|
DesignCapacity
|
The design capacity of the battery in m Watt-hours. If this
property is not supported, enter 0.
|
DesignVoltage
|
The design voltage of the battery in mVolts. If this attribute
is not supported, enter 0.
|
DeviceID
|
An address or other identifying information used to uniquely
name the LogicalDevice.
|
ElementName
|
A user-friendly name for the object. This property allows
each instance to define a user-friendly name in addition to its key
properties, identity data, and description information.
-
NOTE: The Name property of
ManagedSystemElement is also defined as a user-friendly name. But,
it is often subclassed to be a Key. It is not reasonable that the
same property can convey both identity and a user-friendly name, without
inconsistencies. Where Name exists and is not a Key (such as for instances
of LogicalDevice), the same information can be present in both the
Name and ElementName properties.
|
EnabledDefault
|
An enumerated value indicating an administrator's default
or startup configuration for the Enabled State of an element.
Possible values are:
- 2 = Enabled
- 3 = Disabled
- 5 = Not Applicable
- 6 = Enabled but Offline
- 7 = No Default
- 9 = Quiesce
- .. = DMTF Reserved
- 32768..65535 = Vendor Reserved
By default, the element is
Enabled (value =
2).
|
EnabledState
|
An integer enumeration that indicates the enabled and disabled
states of an element. It can also indicate the transitions between
these requested states.
Possible values are:
- 0 = Unknown
- 1 = Other
- 2 = Enabled — Indicates that the element is or could be executing
commands, will process any queued commands, and queues new requests.
- 3 = Disabled — Indicates that the element will not execute commands
and will drop any new requests.
- 4 = Shutting Down — Indicates that the element is in the process
of going to a Disabled state.
- 5 = Not Applicable — Indicates the element does not support being
enabled or disabled.
- 6 = Enabled but Offline — Indicates that the element may be completing
commands, and will drop any new requests.
- 7 = In Test — Indicates that the element is in a test state.
- 8 = Deferred — Indicates that the element may be completing commands,
but will queue any new requests
- 9 = Quiesce — Indicates that the element is enabled but in a restricted
mode.
- 10 = Starting — Indicates that the element is in the process of
going to an Enabled state. New requests are queued.
- 11..32767 = DMTF Reserved
- 32768..65535 = Vendor Reserved
For example, shutting down (value =
4) and starting
(value =
10) are transient states between enabled and disabled.
|
EstimatedChargeRemaining
|
An estimate of the percentage of full charge remaining.
|
EstimatedRunTime
|
An estimate in minutes of the time that battery charge
depletion will occur under the present load conditions if the utility
power is off, or is lost and remains off, or a Laptop is disconnected
from a power source.
|
HealthState
|
Indicates the current health of the element. This attribute
expresses the health of this element but not necessarily that of its
subcomponents.
DMTF has reserved the unused portion of the
continuum for additional HealthStates in the future.
Possible
values are:
- 0 = Unknown — The implementation cannot report on HealthState
at this time.
- 5 = OK — The element is fully functional and is operating within
normal operational parameters and without error.
- 10 = Degraded/Warning — The element is in working order and all
functionality is provided. However, the element is not working to
the best of its abilities. For example, the element may not be operating
at optimal performance or it may be reporting recoverable errors.
- 15 = Minor failure — All functionality is available but some may
be degraded.
- 20 = Major failure — The element is failing. It is possible that
some or all of the functionality of this component is degraded or
not working.
- 25 = Critical failure — The element is non-functional and recovery
may not be possible.
- 30 = Non-recoverable error — The element has completely failed,
and recovery is not possible. All functionality provided by this element
has been lost.
- .. = DMTF Reserved
|
IdentifyingDescriptions
|
An array of free-form strings providing explanations and
details behind the entries in the OtherIdentifyingInfo array. Note
that each entry of this array is related to the entry in OtherIdentifyingInfo
that is located at the same index.
|
Name
|
The Name property defines the label by which the object
is known. When subclassed, the Name property can be overridden to
be a Key property.
|
OperationalStatus
|
Indicates the current statuses of the element. Various operational
statuses are defined. Many of the enumeration's values are self-explanatory.
Possible values are:
- 0 = Unknown
- 1 = Other
- 2 = OK
- 3 = Degraded
- 4 = Stressed — Indicates that the element is functioning, but
needs attention. Examples of
Stressed states are overload,
overheated, and so on.
- 5 = Predictive Failure — Indicates that an element is functioning
nominally but predicting a failure in the near future.
- 6 = Error
- 7 = Non-Recoverable Error
- 8 = Starting
- 9 = Stopping
- 10 = Stopped — Implies a clean and orderly stop
- 11 = In Service — Describes an element being configured, maintained,
cleaned, or otherwise administered.
- 12 = No Contact — Indicates that the monitoring system has knowledge
of this element, but has never been able to establish communications
with it.
- 13 = Lost Communication — Indicates that the ManagedSystem Element
is known to exist and has been contacted successfully in the past,
but is currently unreachable.
- 14 = Aborted — Implies an abrupt stop where the state and configuration
of the element may need to be updated.
- 15 = Dormant — Indicates that the element is inactive or quiesced.
- 16 = Supporting Entity in Error — Indicates that this element
may be
OK but that another element, on which it is dependent,
is in error. An example is a network service or endpoint that cannot
function due to lower-layer networking problems.
- 17 = Completed - Indicates that the element has completed its
operation. This value should be combined with either OK, Error, or
Degraded so that a client can tell if the complete operation Completed
with OK (passed), Completed with Error (failed), or Completed with
Degraded (the operation finished, but it did not complete OK or did
not report an error).
- 18 = Power Mode — Indicates that the element has additional power
model information contained in the Associated PowerManagementService
association.
- .. = DMTF Reserved
- 0x8000.. = Vendor Reserved
OperationalStatus replaces the Status property on ManagedSystemElement
to provide a consistent approach to enumerations, to address implementation
needs for an array property, and to provide a migration path from
today's environment to the future. This change was not made earlier
because it required the deprecated qualifier. Due to the widespread
use of the existing Status property in management applications, it
is strongly recommended that providers or instrumentation provide
both the Status and OperationalStatus properties. Further, the first
value of OperationalStatus should contain the primary status for the
element. When instrumented, Status (because it is single-valued) should
also provide the primary status of the element.
|
OtherIdentifyingInfo
|
OtherIdentifyingInfo captures data, in addition to DeviceID
information, that could be used to identify a LogicalDevice. For example,
you could use this property to hold the operating system's user-friendly
name for the Device.
|
PrimaryStatus
|
Provides a high level status value, intended to align with
Red-Yellow-Green type representation of status. It should be used
in conjunction with DetailedStatus to provide high level and detailed
health status of the ManagedElement and its subcomponents.
Possible values are:
- 0 = Unknown — Indicates the implementation is in general capable
of returning this property, but is unable to do so at this time.
- 1 = OK — Indicates the ManagedElement is functioning normally.
- 2 = Degraded — Indicates the ManagedElement is functioning below
normal.
- 3 = Error — Indicates the ManagedElement is in an Error condition.
- .. = DMTF Reserved
- 0x8000.. = Vendor Reserved
|
RemainingCapacityMaxError
|
The maximum error (as a percentage) in the mWatt-hour data
reported by RemainingCapacity property.
|
RequestedState
|
An integer enumeration that indicates the last requested
or desired state for the element, irrespective of the mechanism through
which it was requested. The actual state of the element is represented
by EnabledState. This property is provided to compare the last requested
and current enabled or disabled states.
Possible values are:
- 0 = Unknown — Indicates the last requested state for the element
is unknown.
- 2 = Enabled
- 3 = Disabled
- 4 = Shut Down
- 5 = No Change
- 6 = Offline — Indicates that the element has been requested to
transition to the Enabled but Offline EnabledState.
- 7 = Test
- 8 = Deferred
- 9 = Quiesce
- 10 = Reboot — Refers to doing a
Shut Down and then moving
to an
Enabled state.
- 11 = Reset — Indicates that the element is first
Disabled and then
Enabled.
- 12 = Not Applicable
- .. = DMTF Reserved
- 32768..65535 = Vendor Reserved
-
NOTE: When
EnabledState is set to
5 (
Not Applicable), then this
property has no meaning. Refer to the EnabledState property description
for explanations of the values in the RequestedState enumeration.
-
NOTE: The
value
No Change (
5) has been deprecated instead of indicating
the last requested state is
Unknown (
0). If the last
requested or desired state is unknown, RequestedState should have
the value
Unknown (
0), but may have the value
No
Change
(
5).
There are two new values in RequestedState
that build on the statuses of EnabledState. These are
Reboot (
10) and
Reset (
11).
Shut Down requests
an orderly transition to the Disabled state, and may involve removing
power, to completely erase any existing state. The Disabled state
requests an immediate disabling of the element, such that it will
not execute or accept any commands or processing requests.
This property is set as the result of a method invocation (such as
Start or StopService on CIM_Service), or can be overridden and defined
as WRITEable in a subclass. The method approach is considered superior
to a WRITEable property, because it allows an explicit invocation
of the operation and the return of a result code.
If knowledge
of the last RequestedState is not supported for the EnabledLogicalElement,
the property is NULL or has the value 12
Not Applicable.
|
SmartBatteryVersion
|
The Smart Battery Data Specification version number that
is supported by this Battery. If the Battery does not support this
function, the value should be left blank.
|
Status
|
A string indicating the current status of the object. Various
operational and non-operational statuses are defined. This property
is deprecated instead of OperationalStatus, which includes the same
semantics in its enumeration. This change is made for three reasons:
- Status is more correctly defined as an array. This definition
overcomes the limitation of describing status using a single value,
when it is really a multi-valued property (for example, an element
may be OK AND Stopped.
- A MaxLen of 10 is too restrictive and leads to unclear enumerated
values.
- The change to a uint16 data type was discussed when CIM V2.0 was
defined. However, existing V1.0 implementations used the string property
and did not want to modify their code. Therefore, Status was grandfathered
into the Schema. Use of the deprecated qualifier allows the maintenance
of the existing property, but also permits an improved definition
using OperationalStatus.
Possible values are:
- OK
- Error
- Degraded
- Unknown
- Pred Fail
- Starting
- Stopping
- Service
- Stressed
- NonRecover
- No Contact
- Lost Comm
- Stopped
|
SystemCreationClassName
|
The CreationClassName of the scoping system.
|
SystemName
|
The System Name of the scoping system.
|
TransitioningToState
|
Indicates the target state to which the instance is transitioning.
Possible values are:
- 0 = Unknown
- 2 = Enabled
- 3 = Disabled
- 4 = Shut Down
- 5 = No Change — Indicates that no transition is in progress.
- 6 = Offline
- 7 = Test
- 8 = Defer
- 9 = Quiesce
- 10 = Reboot
- 11 = Reset
- 12 = Not Applicable — Indicates the implementation does not support
representing ongoing transitions.
A value other than
5 or
12 identifies the state
to which the element is in the process of transitioning.
|