跳至主要內容
  • 簡單快速地下訂單
  • 檢視訂單及追蹤商品運送狀態
  • 建立並存取您的產品清單

How to Quickly Fix a Windows On-screen Error Caused by Changing the SATA Mode

摘要: The following article is a guide to a quick fix for On-screen Windows errors seen after changing your computers Serial AT Attachment (SATA) mode.

本文章適用於 本文章不適用於 本文無關於任何特定產品。 本文未識別所有產品版本。

症狀

Computer restarts with on-screen error ever since the SATA mode is changed

This article is relevant to anyone:

  • That is using Windows 11 or Windows 10.
  • That must change the computers SATA mode.
  • Who does not want to reinstall the operating system every time they change the SATA mode.

This article is not relevant to anyone:

  • That is using Windows 8.1 or earlier.
  • Earlier operating systems require Windows Registry changes to change the SATA mode.
  • This guide does not go into working with the older operating systems.

原因

If you change the SATA mode without reinstalling the Windows operating system, you become subject to crashes and on-screen errors.

There are several reasons why you would want to change the SATA mode. (For example: Such as disabling a Redundant Arrays of Inexpensive Disks Controller (RAID) build or to tweak the performance of your solid state drive (SSD).)

The following guide provides some quick steps to enable you to do this.

解析度

Note: Administrator rights on the faulty computer are required for this resolution.
 
Note: Best practice recommends that before you do any work on your operating system, you complete a full backup. This is in case any problems occur, you can revert to the backup.
 

Run through these steps:

  1. You must open a Command Prompt or PowerShell and give it Administrative Rights:

    1. You can use the keyboard shortcut by pressing on the Windows logo key to open the Start Menu.

    2. Type CMD to open a list of options.

    3. Right-click or press and hold on the Command Prompt link to select Open as Administrator from the submenu that appears.

  2. Run the following command:

    bcdedit /set { current } safeboot minimal

  3. Restart the computer and enter the BIOS screens:

    • Press down on the F2 key when the computer is at the Dell Splash Screen during startup.

    • Alternatively, press down on the F12 key and choose the BIOS from the menu that appears.

  4. Select the required SATA mode, save your changes, and restart the computer.

  5. Windows starts up in SAFE Mode.

  6. Open the Command Prompt as an Administrator again.

  7. Run the following command:

    bcdedit /deletevalue { current } safeboot

  8. Restart Windows again.

Note: You must uninstall the Intel Rapid Storage Technology (IRST) Driver from your computer and install the latest revision from our support site. Enter your service tag, express service code, or select your computer model type to bring up your computers drivers list. Choose your operating system from the list to ensure you have the most recent revision for your operating and computer type.
 
Note: This resolution is intended for computers that do not have an active RAID 0 or 1 configuration. Otherwise reinstalling the operating system is still required.

受影響的產品

Alienware, Inspiron, OptiPlex, Vostro, XPS, Alienware, Inspiron, Latitude, Vostro, XPS, Latitude Tablets, XPS Tablets, Fixed Workstations
文章屬性
文章編號: 000138544
文章類型: Solution
上次修改時間: 21 6月 2024
版本:  6
向其他 Dell 使用者尋求您問題的答案
支援服務
檢查您的裝置是否在支援服務的涵蓋範圍內。