Resolve No Bootable Device Found Error in Legacy Mode on Dell Computers
摘要: Resolve "No bootable devices were found" error on laptops and PCs. Learn how to fix no boot device available, detected, or found by switching to UEFI mode and reinstalling Windows 10 or Linux. ...
本文适用于
本文不适用于
本文并非针对某种特定的产品。
本文并非包含所有产品版本。
症状
Follow the guidelines below to resolve the following error message:
The No boot device Found error appears when the Boot Sequence is set to Legacy mode or the operating system is installed under Legacy mode.
No boot device found error
The following error may appear after operating system installation: No boot device found.
This error occurs when the device BIOS boot sequence is set to Legacy mode.
If the operating system is installed in Legacy mode, the error message appears when you reboot the computer. The failure cannot be recovered by changing the BIOS setting back to Unified Extensible Firmware Interface (UEFI). The operating system should be reinstalled.
Note:
- Only Windows 10 and higher and Linux operating systems in UEFI boot mode are supported on these specific Dell computers.
- Ensure that UEFI mode is enabled in the BIOS before trying to reinstall the operating system.
- Using an Optical Drive to install the operating system is not supported in legacy mode as there is no Optical Drive option in the Boot Menu.
- The above Dell computers have a 7th-generation Coffee Lake processor (and above). The computers are designed to boot exclusively in the UEFI; boot environment.
- As a result, the operating system fails to boot if Legacy boot mode is selected on these computers.
原因
Wrong boot mode set in BIOS.
解决方案
If the operating system is installed with UEFI before the boot sequence is changed, the computer can be recovered by changing the Boot sequence back to UEFI.
If the operating system is installed with Legacy mode, the computer cannot be recovered by changing the Boot sequence back to UEFI mode.
Operating system reinstallation should be performed.
Follow the steps below to reinstall Windows 10 or higher:
- From a power off state, power on the computer and Press F2 at the Dell logo to boot into the BIOS setup menu.
- Choose Boot sequence and change the option from Legacy to UEFI then click Apply in the lower right corner of the screen:
- Choose Advanced Boot Options and disable Enable Legacy Option ROMs then click Apply in the lower right corner of the screen:
- Choose Secure Boot -> Secure Boot Enable and change the option from Disabled to Enabled.
- Then click Apply in the lower right corner of the screen:
- Click Exit in the lower right corner of the screen and wait for the computer to reboot.
- Reinstall the Windows 10 operating system.
Follow the steps below to install the Linux operating system:
- Follow steps 1 through 3 from the steps above for installing Windows 10 (these steps are the same for a Linux install).
- Verify the Secure Boot > Secure Boot Enable option is Disabled in the BIOS:
- Choose SATA Operation -> SATA Operation and change to AHCI mode:
- Click Exit in the lower right corner and wait for the computer to reboot.
- Reinstall the Linux operating system.
其他信息
Recommended Articles
Here are some recommended articles related to this topic that might be of interest to you.
受影响的产品
OptiPlex 3060 Tower, OptiPlex 3060 Micro, OptiPlex 3060 Small Form Factor, OptiPlex 5060 Tower, OptiPlex 5060 Micro, OptiPlex 5060 Small Form Factor, OptiPlex 7060 Tower, OptiPlex 7060 Micro, OptiPlex 7060 Small Form Factor, Precision 3630 XL Tower
, Precision 3430 Small Form Factor, Precision 3630 Tower
...
文章属性
文章编号: 000128655
文章类型: Solution
上次修改时间: 17 10月 2024
版本: 10
从其他戴尔用户那里查找问题的答案
支持服务
检查您的设备是否在支持服务涵盖的范围内。