Ga naar hoofdinhoud
  • Snel en eenvoudig bestellen
  • Bestellingen en de verzendstatus bekijken
  • Een lijst met producten maken en openen

How to Restore Factory Defaults on Dell EMC Force10 S4810, S4820T, Z9000, Z9500, S6000, S60, S55 and S5000 switches

Samenvatting: How to Restore Factory Defaults on Dell Networking Force10 S4810, S4820t, Z9000, Z9500, S6000, S60, S55 and S5000 switches.

Dit artikel is van toepassing op Dit artikel is niet van toepassing op Dit artikel is niet gebonden aan een specifiek product. Niet alle productversies worden in dit artikel vermeld.

Instructies



This article explains how to Restore Factory Defaults on Dell Networking Force10 S4810.
 


Important Points to Remember 

  • When you restore all the units in a stack, these units are placed in standalone mode.
  • When you restore a single unit in a stack, only that unit is placed in standalone mode. No other units in the stack are affected.
  • When you restore the units in standalone mode, the units remain in standalone mode after the restoration.
  • After the restore is complete, the units power cycle immediately.
 


Command to Restore Factory Default

   
Restoring factory defaults will delete the existing persistent settings (configuration, stacking, fanout, etc.) After restoration the unit(s) will be power cycled immediately. Proceed with CAUTION !

 

Command

Parameters

FTOS# restore factory-defaults stack-unit {0-5 | all} {bootvar | clear-all | nvram}

Restores and clears config, stacking, fanout, etc..
0-5 - indicates the switch number to be factory reset
all - indicates all switches to be factory reset
Bootvar - Reset Boot environment variables
Clear-all - Reset BootVar, NvRam and configurations
NvRam - Reset NvRam

 

HOW10777_en_US__1icon Note: This command feature was introduced in firmware version 8.3.3.9. You will need to have 8.3.3.9 firmware or newer in order to have this command option available.  

Examples 

Example of resetting all stack units:
FTOS#restore factory-defaults stack-unit all nvram
**************************************************************
* Warning - Restoring factory defaults will delete the existing *
* startup-config and all persistent settings (stacking, fanout, etc.)*
* All the units in the stack will be split into standalone units. *
* After restoration the unit(s) will be powercycled immediately. *
* Proceed with caution !
***************************************************************
Proceed with factory settings? Confirm [yes/no]:yes
-- Restore status --
Unit Nvram Config
------------------------
0 Success Success
1 Success Success
2 Success Success
3 Not present
4 Not present
5 Not presentPower
Power-cycling the unit(s).
 
Example of resetting single switch
 
FTOS#restore factory-defaults stack-unit 1 nvram
*************************************************************
*Warning - Restoring factory defaults will delete the existing *
* persistent settings (stacking, fanout, etc.) *
* After restoration the unit(s) will be powercycled immediately. *
* Proceed with caution ! *
**************************************************************
Proceed with factory settings? Confirm [yes/no]:yes
-- Restore status --
Unit Nvram Config
------------------------
1 Success
Power-cycling the unit(s)

Getroffen producten

PowerSwitch S4810P, PowerSwitch S5000, Force10 S55T, Force10 S60-44T, PowerSwitch S6000, PowerSwitch S6000 ON, Force10 Z9000, Dell Networking Z9500
Artikeleigenschappen
Artikelnummer: 000103011
Artikeltype: How To
Laatst aangepast: 16 sep. 2021
Versie:  4
Vind antwoorden op uw vragen via andere Dell gebruikers
Support Services
Controleer of uw apparaat wordt gedekt door Support Services.