How To Switch NVMe for Precision 5820 and 7820 Tower
요약: This article describes the steps required to install the Customer Kit on the Precision 5820/7820 Tower to connect and enable PCIE-SSD Storage to the front FlexBay.
이 문서는 다음에 적용됩니다.
이 문서는 다음에 적용되지 않습니다.
이 문서는 특정 제품과 관련이 없습니다.
모든 제품 버전이 이 문서에 나와 있는 것은 아닙니다.
지침
Table of Contents:
Before You Begin
The article below provides information about safe practices to consider before working with electrical equipment.
Two side-by-side pairs will be treated as a single FlexBay (Figure 1). The backplane consists of two pairs, so it must be replaced on a FlexBay basis.
(Figure 1. FlexBay)
Removal Instructions
| 1 | Phillips screwdriver with shaft length × 20cm (+2×200) |
| 2/3 | 2.0/2.5mm Plus Driver |
Note: Be aware that using a large Phillips or Flat Head screwdriver may result in damage to the head of the screws. This would make their removal impossible without specialty tools, that are not available to our onsite engineers.
The following parts will be required to replace SATA/SAS with PCIe SSD.
- [575-BBSH] - M.2 Module for FlexBay incl. carrier 58/78/7920 Towers (Kit)
- [750-ABDF] - Convert HDD FlexBay to PCIe SSD FlexBay 58/78 Towers (Kit)
Remove the following parts before the replacement.
- Precision 5820 Tower
- Go to Precision 5820 Tower System Manual > Removing and installing components
- Side cover > Removing the side cover
- Air shroud > Removing the air shroud
- Hard disk drive assembly > Removing the HDD carrier
- Front bezel > Removing the front bezel
- 5.25 inch ODD bracket > Removing the 5.25 ODD bracket
- System fan > Removing the System fan
- Go to Precision 5820 Tower System Manual > Removing and installing components
- Precision 7820 Tower
- Go to Precision 7820 Tower System Manual > Removing and installing components
- Side cover > Removing the side cover
- Air shroud > Removing the air shroud
- Hard disk drive assembly > Removing the HDD carrier
- Hard Disk Drive bezel > Removing HDD bezel
- 5.25 inch ODD bracket > Removing the 5.25 ODD bracket
- Graphical processing unit(GPU) > Removing the GPU
- System fan > Removing the System fan
- Go to Precision 7820 Tower System Manual > Removing and installing components
- Remove the power cable.
- Remove the 3 screws.
- Follow the cables on the backplane and remove the unnecessary cables from the SATA port on the motherboard.
PCIe SSD Backplane
| 1 | Thermal Sensor Cable |
| 2 | Data Cable |
Step to install PCIe SSD Backplane
- Attach the backplane to the system.
- Secure the backplane with the 3 screws.
There are 3 cables to be connected.
| 1 | Power Cable | 2 | Data Cable |
| 3 | Thermal Sensor Cable | 4 | A hook to secure Thermal Sensor Cable |
Step to install cables
- Installing Thermal Sensor Cable
- Secure the thermal sensor cable with the hook.
- Connect the thermal sensor cable to TEMP_FLEX0 or TEMP_FLEX1 on the motherboard.
- Secure the thermal sensor cable with the hook.
- Installing Power Cable
- Connect the 6-pin power cable from the power supply unit to the backplane.
- Connect the 6-pin power cable from the power supply unit to the backplane.
- Installing Data Cable
- Connect the upper data cable (U.2_P1) to PCIE1 port on the motherboard, lower data cable (U.2_P0) to PCIE0 port on the motherboard.
- Connector for Precision 5820 is located next to CPU
- Connector for Precision 7820 is located next to Power Supply Unit
- Connector for Precision 5820 is located next to CPU
- Connect the upper data cable (U.2_P1) to PCIE1 port on the motherboard, lower data cable (U.2_P0) to PCIE0 port on the motherboard.
Step to install M.2 SSD can be learned from the following video:
Install the following parts after the replacement.
- Precision 5820 Tower
- Go to Precision 5820 Tower System Manual > Removing and installing components
- System fan > Installing the system fan
- 5.25 inch ODD bracket > Installing the 5.25 ODD bay
- Front bezel > Installing the front bezel
- Hard disk drive assembly > Installing the HDD carrier
- Air shroud > Installing the air shroud
- Side cover > Installing the side cover
- Go to Precision 5820 Tower System Manual > Removing and installing components
- Precision 7820 Tower
- Go to Precision 7820 Tower System Manual > Removing and installing components
- System fan > Installing the system fan
- Graphical processing unit(GPU) > Installing the GPU
- 5.25 inch ODD bracket > Installing the 5.25 ODD bay
- Front bezel > Installing the front bezel
- Hard disk drive assembly > Installing the HDD carrier
- Air shroud > Installing the air shroud
- Side cover > Installing the side cover
- Go to Precision 7820 Tower System Manual > Removing and installing components
추가 정보
Recommended Articles
Here are some recommended articles related to this topic that might be of interest to you.
- Upgrading Storage in the Dell Precision 5820, 7820, and 7920 Tower Workstations
- Dell Precision 5820 and 7920: Imaging Steps for NVMe Drives in the Flex Bay
- Precision Tower 5820: Visual guide to your Computer
- Precision 5820 Tower Teardown removal guide for customer replaceable units (CRUs)
- Dell Precision Tower 7820 Workstation System Guide
해당 제품
Precision 5820 Tower, Precision 7820 Tower문서 속성
문서 번호: 000185631
문서 유형: How To
마지막 수정 시간: 23 4월 2024
버전: 7
다른 Dell 사용자에게 질문에 대한 답변 찾기
지원 서비스
디바이스에 지원 서비스가 적용되는지 확인하십시오.