How to create a Stack on Dell Networking Force10 S25/S50 Switch
요약: This Article explains how to create a Stack on Dell Networking Force10 S25/S50 Switches
이 문서는 다음에 적용됩니다.
이 문서는 다음에 적용되지 않습니다.
이 문서는 특정 제품과 관련이 없습니다.
모든 제품 버전이 이 문서에 나와 있는 것은 아닙니다.
지침
Objectives
- Important Points to Remember
- Needed Hardware
- Creating Stack
- Verify System and Stack-Port Status
- Reset a Switch Removed from Stack to Default
Important Points to Remember
- You may stack up to eight S25/S50 systems in combination.
- The S25 and S50 systems support mixed stacking, as long as the units have the same FTOS version.
- You may not connect 12G and 24G stack ports.
Needed Hardware
Stacking Modules
- not interchangeable
- Types
24 Gigabit - 1 port, Install 2 modules for Ring Topology
12 Gigabit - 2 port
Cables
- bi-directional
- length
4 meters
60 centimeters
Picture of Hardware Components
Creating a Stack
| Command |
Purpose |
| FTOS# show version |
Verify that each unit has the same FTOS version prior to stacking them together. |
| FTOS# stack-unit renumber |
Pre-configure unit numbers for each unit so that the stacking is deterministic upon boot up. (Optional) |
| FTOS(config)# stack-unit priority |
Configure the switch priority for each unit to make management unit selection deterministic. (Optional) |
| Connect the units using stacking cables and modules |
|
| FTOS# show system brief |
Power the stack one unit at a time. Start with the management unit, then the standby, followed by each of the members in order of their assigned stack number (or the position in the stack you want each unit to take). Allow each unit to completely boot, and verify that the unit is detected by the stack manager, and then power on the next unit. |
Verify System and Stack-Port Status
Stack#show system stack-ports
Topology: Daisy chain
Interface Connection Link Speed Admin Link Trunk
(Gb/s) Status Status Group
-----------------------------------------------------------------------------------------
0/51 12 up down
0/52 1/50 12 up up
1/49 2/52 12 up up
1/50 0/52 12 up up
2/51 12 up down
2/52 1/49 12 up up
Stack#show system brief
Stack MAC : 00:01:e8:d5:f9:6f
-- Stack Info --
Unit UnitType Status ReqTyp CurTyp Version Ports
-------------------------------------------------------------------------------------------------------
0 Standby online S50V S50V 7.8.1.0 52
1 Management online S50N S50N 7.8.1.0 52
2 Member online S50V S50V 7.8.1.0 52
Reset a Switch Removed from Stack to Default
The running-configuration and startup-configuration are synchronized on all stack units. A stack member that is disconnected from the stack maintain this configuration.
To remove a stack member from the stack, disconnect the stacking cables from the unit. You may do this at any time, whether the unit is powered or unpowered, online or offline.
The stack continues to use the primary switch chassis MAC address even after a failover. The MAC address is not refreshed until the stack is reloaded and a different unit becomes the stack manager.
NOTE: If the removed management unit is brought up as a standalone unit or as part of a different stack, there is a possibility of MAC address collisions.
NOTE: If you remove a unit in the middle of the stack, the stack will be split into multiple parts, and each will form a new stack according to the stacking algorithm.
| Command |
Purpose |
| FTOS# reset stack-unit 0-11 |
Reload a stack-unit. |
| FTOS# reset-self |
Reload a member unit, from the unit itself. |
| FTOS# reset stack-unit 0-11 hard |
Reset a stack-unit when the unit is in a problem state. |
해당 제품
Force10 S25N-S50N, Force10 S25-01-GE-24P, Force10 S25-01-GE-24T, Force10 S25-01-GE-24V, Force10 S50-01-GE-48T-V, Force10 S50-01-GE-48T, Force10 S50P문서 속성
문서 번호: 000122529
문서 유형: How To
마지막 수정 시간: 30 3월 2021
버전: 4
다른 Dell 사용자에게 질문에 대한 답변 찾기
지원 서비스
디바이스에 지원 서비스가 적용되는지 확인하십시오.