メイン コンテンツに進む
ログアウト

Dellへようこそ

マイアカウント
  • すばやく簡単にご注文が可能
  • 注文内容の表示、配送状況をトラック
  • 会員限定の特典や割引のご利用
  • 製品リストの作成とアクセスが可能
ログイン アカウントの新規作成 プレミアログイン パートナー プログラム サインイン
お問い合わせ

Dell.comカート

How to perform interface range commands on Force10 Switches

概要: how to use range command on Dell Force10 switch, Dell Force10 how to use interface range command

この記事は次に適用されます：   この記事は次には適用されません： 
リソースをチェックアウト：

手順

 


This article explains how to configure multiple interfaces or VLANs at the same time.


Table of Contents


1.  Configure multiple interfaces at the same time
2.  Configure multiple VLANs at the same time



Configure multiple interfaces at the same time


To configure multiple interfaces at the same time, go into an interface range command.

Input the following commands to enter a range of interfaces.

ftos>enable

ftos#configure

For consecutive ports, the following example uses 10-Gigabit Ethernet ports 2-5 on Unit 0

ftos(config)#interface range te 0/2 - 5

For non-consecutive ports, the following example uses 10-Gigabit Ethernet ports 48 on Unit 0 and 3

ftos(config)#interface range te 0/48 , te 3/48

Note: Notice that starting after range there are spaces after every input in the rest of the command syntax for both examples
 
Note: To verify the way the ports are defined on your switch, you can run an ftos#show interfaces status

Below is an example to configure the 10-Gigabit Ethernet consecutive ports 1 through 5, as well as 8 and 9 on unit 0

ftos(config)#interface range gi 0/1 - 5 , gi 0/8 , gi 0/9

Note: You may configure different interface types at the same time, such as a Gigabit Ethernet, and 10-Gigabit Ethernet interface
 
Note: If the syntax of the desired range command is large, it may be easier to type it in notepad and then paste it in the command line.

 

Note: Non existing interfaces are excluded from bulk configuration
  


Configure multiple VLANs at the same time


 

Note: Interface range for VLANs does not create new VLANs. It will only configure existing VLANs. Non existing interfaces are excluded from bulk configuration

 

To configure multiple VLANs at the same time, go into an interface range command.

Input the following commands to enter a range of VLANs.

For consecutive VLANs, the following example uses VLANs 2-10

ftos(config)#interface range vlan 2 - 10

For non-consecutive VLANs, the following example uses VLANs 15 and 20

ftos(config)#interface range vlan 15 , vlan 20

Note: Notice that starting after range there are spaces after every input in the rest of the command syntax for both examples
 

Below is an example to configure the VLANs 2 through 10, as well as 15 and 20.

ftos(config)#interface range vlan 2 - 10 , vlan 15 , vlan 20

対象製品

Force10 S60-44T
文書のプロパティ
文書番号: 000121358
文書の種類: How To
最終更新: 10 4月 2021
バージョン:  3
質問に対する他のDellユーザーからの回答を見つける
サポート サービス
お使いのデバイスがサポート サービスの対象かどうかを確認してください。