Passer au contenu principal
Quitter

Bienvenue dans l’univers Dell

Mon compte
  • Passer des commandes rapidement et facilement
  • Afficher les commandes et suivre l’état de votre expédition
  • Profitez de récompenses et de remises réservées aux membres
  • Créez et accédez à une liste de vos produits
Se connecter Créer un compte Connexion au compte Premier Connexion au programme de partenariat
Nous contacter

Vos paniers Dell.com

Latitude 5400 Teardown Removal Guide for Customer Replaceable Units (CRUs)

Résumé: This page is a guide to those parts of the Dell Latitude 5400 that it considers OK for anyone to remove and replace

Cet article concerne Cet article ne concerne pas Cet article n’est associé à aucun produit spécifique. Toutes les versions du produit ne sont pas identifiées dans cet article.
Consulter d’autres ressources

Instructions

These guides will take you step by step through the safe removal of what are considered to be the Customer Replaceable Unit (CRU) parts of a Latitude 5400. (CRUs are the parts of the system that shouldn't need an engineer to remove or replace.) The guides will also include pictures to reference what's involved.

Table of Contents:

  1. CRU Removal Guide
  2. Removal Instructions

 

Removal Guide

 

If these guides do not cover what you are looking to do, then you will want to reference your System Manual.

The article below provides information on safe practices to take into consideration before working with electrical equipment.


Back to Top

 

Removal Instructions

 

Note: Please click on the title of the section you want to open below, in order to see the contents.
 
|

 

SLN317473_en_US__2ReqTools_E7450_BKeith_01

1 Small Phillip's head screwdriver 2 Plastic Scribe
3 Small Flat head screwdriver    
 
Note: Be aware that using a large Phillips or Flat Head screwdriver may result in damage to the head of the screws. This would make their removal impossible without Special tools, that aren't available to our onsite engineers.

 

  1. Pre-Removal Instructions Before removing the microSD card Card :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

  2. Press in on the microSD card [1] and remove it from the computer [2].

SLN317473_en_US__4P_3540_SDcard

 

  1. Pre-Removal Instructions Before removing the Main Access Panel :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the microSD card

  2. Loosen the eight captive screws that secure the base cover to the computer.

SLN317473_en_US__5Base1_Lat_5400

  1. Pry the base cover from the edge using a plastic scribe [1, 2].

SLN317473_en_US__6Base2_Lat_5400

Note: While removing the base cover, on-site technicians must take care to remove the base cover carefully. There are prying recess points next to the left and right hinges which ease the disassembly procedure. With the help of a plastic scribe, pry open from the top left side of the base cover, continue working your way around the left and right side of the base cover, then remove the base cover from the system.

  1. Lift the base cover from the computer.

SLN317473_en_US__8Base3_Lat_5400

 

  1. Pre-Removal Instructions Before removing the Battery :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the microSD card and Bottom Door

  2. Disconnect the battery cable from the connector in the system board.

SLN317473_en_US__9P_3540_Battery_1

  1. Remove the one (M2.0x4.0) screw that secures the battery to the palmrest [1].

  1. Remove the battery from the computer [2].

SLN317473_en_US__10P_3540_Battery_2

 

  1. Pre-Removal Instructions Before removing the WLAN Card (WiFi, Wireless) :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the microSD card, Bottom Cover and Battery

  2. Remove the single screw that secures the WLAN bracket to the computer [1] and lift the bracket away from the computer [2].

  1. Disconnect the two wireless antennas from the wireless card [3] and slide the card out of the connector [4].

SLN317473_en_US__11P_3540_WLAN

 

  1. Pre-Removal Instructions Before removing the Memory :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the microSD card, Bottom Cover and Battery

  2. 1.Gently pry on the memory module latch [1] and slide it out of the slot [2].

SLN317473_en_US__12P_3540_Memory

 

  1. Pre-Removal Instructions Before removing the Solid State Drive (SSD) :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the microSD card, Bottom Cover and Battery

  2. Remove the two screws that secure the SSD to computer [1] and slide the SSD module along with the metal bracket from the connector [2].

SLN317473_en_US__13P_3540_SSD_1

  1. Turn the metal bracket over and detach the SSD module from the thermal pad on the metal bracket.

SLN317473_en_US__14P_3540_SSD_2

 

  1. Pre-Removal Instructions Before removing the Coin-Cell Battery :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the microSD card, Bottom Cover and Battery

  2. Disconnect the coin cell battery cable from the connector on the system board [1].

  1. Lift the coin cell battery from the system board [2].

SLN317473_en_US__15Coin1_Lat_5400

Produits concernés

Latitude 5400
Propriétés de l’article
Numéro d’article: 000134814
Type d’article: How To
Dernière modification: 07 juil. 2023
Version:  5
Trouvez des réponses à vos questions auprès d’autres utilisateurs Dell
Services de support
Vérifiez si votre appareil est couvert par les services de support.