* IOCA nie ma na celu zastąpienia przeglądu dokumentów związanych z aktualizacją w ramach przygotowań do działań związanych z aktualizacją. Zapoznaj się z przewodnikiem po planowaniu aktualizacji OneFS i procesach:
Poniżej dostępny jest film wprowadzający. Podczas uruchamiania w klastrze zawsze upewnij się, że używasz najnowszej wersji.tar -zxvf IOCA.tar
isi_for_array cat /etc/isilon_serial_number
mkdir -pv /ifs/data/Isilon_Support
cd /ifs/data/Isilon_Support
Umieść najnowszą wersję IOCA w klastrze w katalogu /ifs/data/Isilon_Support/:
perl IOCA -vUruchom narzędzie IOCA, dodając dodatkowe argumenty. W poniższym przykładzie kontrola przed aktualizacją obejmuje sprawdzenie uaktualnienia do wersji 9.5.1.0 i wyświetla zalecenie dotyczące planu uaktualnienia po wynikach kontroli poprawności działania:
perl IOCA -u 9.5.1.0
BMC/CMC Hardware Monitoring FAIL
FAIL: Hardware monitoring issues detected on nodes: 2
INFO: 3 nodes have out of date CMC firmware versions: 1-3
INFO: Refer to KB489050 (https://support.emc.com/kb/489050) for details.
W tym przykładzie pokazano błąd FAIL dla węzła 2, mającego problemy z monitorowaniem sprzętu. Zawiera również INFO pokazujące, że wersje oprogramowania wewnętrznego kontrolera CMC są nieaktualne w węzłach 1–3. I wreszcie zawiera artykuł z bazy wiedzy z etapami rozwiązania.
IOCA uruchamia się w taki sam sposób w klastrach z włączonym trybem zgodności, jak w przypadku klastrów bez trybu zgodności. Nie ma wymogu, aby uruchamiać go za pomocą sudo. Jednakże użytkownik compadmin musi być właścicielem skryptu IOCA, aby można go było uruchomić.
Poniżej przedstawiono zastosowanie IOCA i dostępnych argumentów lub filtrów:
Usage: IOCA [options] [destination OneFS version] -d, --debug Display debugging information -e, --extra Displays extra details as part of each check -j, --json Displays output in JSON format -v, --version Displays current script version -h, --help Displays this help screen -r <checkName>, --run=<checkName> Executes only the specified check, can be included multiple times -u, --upgradeplan Includes an upgrade plan after health checks --rolling Provide rolling reboot plans --parallel Provide parallel reboot plans [where supported] --simultaneous Provide simultaneous reboot plans [excludes node firmware] -o, --onefs Supports the following comma separated options [ex. 8.1.2,simultaneous]: <version> Uses the provided destination OneFS version simultaneous Simultaneous OneFS upgrade parallel Parallel OneFS upgrade [requires 8.2.2+] rolling Rolling OneFS upgrade exclude-nf Upgrade plans will combine OneFS + node firmware by default [9.2 feature], this option disables that -p, --patches Supports the following comma separated options [ex. none,simultaneous]: none Opt out of patch recommendations simultaneous Simultaneous patch installs parallel Parallel patch installs [requires 9.1+] rolling Rolling patch installs -nf, --node-firmware Supports the following comma separated options [ex. 10.3.3,parallel]: <version> Uses the provided version for node firmware checks none Opt out of node firmware recommendations simultaneous Simultaneous node firmware updates [requires 8.2+] parallel Parallel node firmware updates [requires 8.2+] rolling Rolling node firmware updates -df, --drive-firmware Supports the following comma separated options [ex. 1.32]: <version> Uses the provided version for drive firmware checks none Opt out of drive firmware recommendations -vf, --verify-files Runs checks on files within specified location [ex. /ifs/data/] of certain file type [ex. .isi, .tgz, .tar.gz, .tar] <file location> default location is /ifs/data/ - specify the location where the upgrade files were placed
--run=CHECK
perl
onefs94-a-1# perl IOCA --run=CHECK
Isilon On-Cluster Analysis 0.1541
Requested checks, check, was not recognized.
Available checks are:
checkA100Root Checks if A100 node root mirrors need to be resized to 2GB
checkAPIAuth checks for API auth set to basic where upgrading from 8.1.2.0 to 9.2 or higher
checkAccessZones Checks if multiple access zones are configured for upgrades across 7.1.1. Checks for nested or overlapping SMB shares. Adds warnings when any non-System access zone pools are found, only applies for upgrades across OneFS 7.1.1
checkAggregationMode Checks that the aggregation mode is not Legacy FEC mode for upgrades to OneFS 8+
checkAspera Checks if any aspera services are enabled. If performing OneFS upgrades it must be reinstalled post-upgrade
checkAuthStatus Checks authentication status on each node. Warns if any authentication providers are not online or active. Checks for RFC2307 and Auto-locate of GID/UIDs and points to KB 000028577
checkBBUDegCap Checks for the level of BBU degradation on Gen6 nodes and flags any nodes with excessive degradation which would increase the risk of the node going into an RO state.
checkBMCandCMC Checks for BMC/CMC related issues
checkBXENodes Checks for existence of nodes with BXE interfaces, also checks for KB 000048172 & KB 000064027 known issues
checkBootDisks Checks boot disk wear life remaining, firmware level, and historic error count
checkCM6FWBug Checks drive firmware versions for the criteria of FCO F022318EE
checkCMOSTimeCentury Check if the century configured in CMOS time matches the current century
checkCapacity Verifies cluster capacity based on documented numbers the Upgrade Planning and Progress Guide. Warns if approaching
checkCloudPools Checks for CloudPools related issues
checkConfCmtSyntax Checks sysctl.conf for comments without leading # symbol that would pose an issue in parsing conf file.
checkContact Displays contact information configured in CELog when run with the --extra argument
checkCoreDumps Checks for recent unexpected process restarts reported in /var/log/messages
checkDTA000194434 Checks for criteria of KB 000194434
checkDestinationOneFS Checks destination OneFS version
checkDiskpools Checks diskpools and class equivalence for OneFS upgrades going across 7.0
checkDriveFirmware Checks for out of date Drive Firmware and calls other related drive firmware checks
checkDriveLoad Checks the current load on the drives
checkDriveStallTimeout Checks current Drive Stall Timeout setting, recommend value is 3.5 seconds (3500000 microseconds) or higher
checkDriveSupportPackage Checks for drive firmware updates available in the Drive Support Package
checkDrivesHealth Checks health of drives and the drive stall timeout setting in sysctl
checkET004252 Checks for criteria of ET004252
checkETAs Checks for Technical Advisories
checkEmailSettings Displays E-mail settings configured in CELog when run with the --extra argument
checkEncoding Checks exports and cluster configuration for if utf-8/default encoding
checkEvents Checks events on all the nodes, failure if any critical events exist
checkFCOF022318EE Checks drive firmware versions for the criteria of FCO F022318EE
checkFCOF031617FC Checks drive firmware versions for the criteria of KB 000024620
checkFCOF042415EE Checks the cluster to see if it meets criteria for FCO F042415EE/KB 000051631
checkFileSharing Checks if Atime is enabled
checkFilepoolPolicies Checks GNA requirements and checks filepools for final match being set and names starting with a number
checkFirmwarePackages In OneFS 9.1 and later, confirms firmware packages are available
checkFlush Checks for running flush processes / active pre_flush screen sessions on clusters
checkGatewayPriority Checks for subnets with duplicate gateway priorities
checkGroups Checks nodes for all enabled protocols. Fails if group info is reporting that an enabled protocol is not functioning on any node
checkHDFS Display HDFS details, only useful when run with --extra
checkHardening Checks if FIPS is enabled on node in the cluster, this needs to be disabled prior to upgrades to 9.5 or higher and re enabled after to avoid assessment failures
checkHardwareStatus Checks battery health, power supplies, and gathers hardware details for use elsewhere
checkHardwareUpgrade Checks if there is an in progress hardware upgrade
checkHealth Verifies cluster health status and node health status
checkIBInterfaces Checks for ib0/1 as being active, checks for ETA180317 IB switch firmware versions, and checks for overlapping IB networks
checkIBPCIeSlot Checks if the InfiniBand card is installed in the wrong slot which may lead node start up issues during an upgrade to OneFS 9 and later releases
checkIDI Checks for IDI errors in the past 90 days
checkISCSI Checks for iSCSI LUNs being configured in /ifs/.ifsvar/iscsi/iscsi.conf (OneFS prior to 8.x only)
checkIndexSnapshotCurrent Checks for current snapshots that are over 2 weeks old and may contirbute to capacity issues
checkInternalPing Checks internal network by performing network ping operations
checkJobHistory Checks job history for issues, currently just MediaScan issues
checkJobStatus Checks for running jobs that would impact an upgrade
checkJobs Checks jobs
checkKB000066019 Checks size of reports.db and flags if over 100MB which may lead to issues outlined on KB 000066019
checkKB000081658 Checks for criteria of KB 000081658
checkKB000181818 Checks for criteria of KB 000181818
checkKB000192800 Checks for critera of KB 000192800
checkKB000196175 Checks for criteria of KB 000196175
checkKB000196762 Checks for criteria of KB 000196762
checkKB000197850 Checks for issues with IB queue pairs that would lead to node reboot issues if IB queue pairs are in a degraded state
checkKB000212387 Checks Authentication providers msDS-SupportedEncryptionTypes attribute to ensure a value is set and assigned, if it is not, there is potential for DU after an upgrade to 9.5 or above.
checkKB000213188 Checks for SED hardware where current version is less than 9.2 and destination version is 9.5 or higher.
checkKB201488 Checks if any node meets criteria for KB 000201488
checkKB201666 Checks if it is necessary to perform the proactive workaround from KB 000201666 for a patch installation and whether the pre-requisites are met
checkKB201933 Checks for criteria of KB 000201933
checkKB203381 Checks for criteria of KB 203381
checkKB220014 Checks for criteria of KB 220014
checkKB462202 Checks BootOrder in bios_settings.ini on Generation 5 nodes to determine if at risk for KB 000025523
checkKB489473 Checks if any node meets criteria for KB 000061983
checkKB490849 Checks if at risk for KB 000052089
checkKB496582 Checks for auth rules issues detailed in KB 000160596
checkKB496993 Checks if the cluster is at risk for KB 000061504
checkKB501267 Checks for the criteria of KB 000026510
checkKB507031 Checks for criteria outlined in KB 000035398
checkKB516613 Checks if any node meets criteria for KB 000057267
checkKB519119 Checks if nodes may be impacted by KB 519119
checkKB519388 Pre-upgrade check for issues outlined in KB 000162270
checkKB519423 Checks if the cluster config files are in a mixed mode
checkKB519890 Checks for a known issue with LAGG interfaces in LACP mode when running OneFS 8.0.0.6, 8.0.1.2, 8.1.0.2, and 8.1.1.1
checkKB521778 Checks for criteria outlined in KB 000031948
checkKB521890 Checks for criteria outlined in KB 000167681
checkKB524082 Checks if the cluster is enabled for HTTP clients and flags a compatibility issue caused by a change in Apache versions
checkKB527312 Check for criteria of KB 000166965
checkKB530050 Check for criteria of KB 000040987
checkKB533516 Checks if cluster uses an IP for AWS CloudPool accounts putting it at risk for DTA 533516
checkKB535582 Checks if at risk for KB 000060471
checkKB537785 Check for criteria of KB 000168829
checkKB540000 Checks for criteria of KB 000058599
checkKB540071 Checks for existence of files under /var/fw/fwpkg when no IsiFw package is installed
checkKB540513 Checks for criteria of KB 000174074
checkKB540872 Checks if the cluster may encounter KB 000170982 during an upgrade from OneFS 8.2 releases
checkKB540901 Checks boot disk partitions for any mismatches in uuids which may lead to boot failures
checkKB544401 Check for critera of KB 000173157
checkKB544854 Check for criteria of KB 000173432
checkKB546604 Checks for criteria of KB 000180866
checkKerberos8000 Checks for an issue with the Kerberos configuration file when upgrading to OneFS 8.0.0.0
checkLACPSFP Checks for LACP on cxgb interfaces for KB 000174095
checkLWIODLog Checks /var/log/lwiod.log for known errors occuring in the last 30 days
checkLastZoneID8000 Checks for gaps in access zones that may cause major issues when upgrading to OneFS 8.0.0.0
checkLeakFreeBlocks Checks for nodes with efs\.lbm\.leak_freed_blocks enabled.
checkLegacyLDAP Checks for Legacy LDAP being enabled in OneFS 6 to OneFS 7 upgrades
checkLicense Checks licenses and gives direction based on licensed features. InsigntIQ and vCenter licenses, gives information from compatibility guide. iSCSI, instructs to only perform simultaneous OneFS upgrades and that it is not supported in 8.0
checkLinMasterPadding Checks the LIN master padding to be all zeros
checkListenQueue Checks for listen queue overflows to be less than 50,000 per node
checkLogLevel Checks LWSM log levels for NFS, SMB, HDFS, and Authentication
checkLogs Checks Log file presence and flags if any log file specified in list is not present
checkMaintenanceMode Checks if the cluster is currently in maintenance mode
checkMemory Checks each DIMM to meet criteria outlined in KB 000041666 and if the expected (per product info line) matches closely the reported RAM
checkMessagesLog Checks /var/log/messages.log for known errors occuring in the last 30 days
checkMirrors Checks the boot mirror health
checkNDMP Checks for running NDMP sessions
checkNDMP16GB Checks for LNN changes that have occurred since the isi_ndmp_d processes started which can cause issues during the HookDataMigrationUpgrade phase of an OneFS upgrade
checkNDMPUpgradeTimeout Checks for LNN changes that have occurred since the isi_ndmp_d processes started which can cause issues during the HookDataMigrationUpgrade phase of an OneFS upgrade
checkNFS Uses nfsstat to identify RPC errors
checkNetBIOS Checks if the Isilon NetBIOS Name Service (nbns) is enabled when updating to OneFS 8.0.1 and later
checkNetstat Checks connections counts for specific protocols via netstat
checkNetworkParallelUpgrade Checks for the risk of inaccessible network pools during a parallel upgrade
checkNetworkPoolIFaces Checks each network pool and their assigned interfaces, if only 1 interface is configured for any pool and IP Ranges are set, this will cause a failure for pre upgrade mandatory checks
checkNodeCompatibility Checks node compatibility for OneFS upgrades by comparing it against known supported versions
checkNodeFirmware Checks node firmware for updates
checkNodesInstalled Checks for nodes installed to display in an agregated list for visibility
checkOneFSVersions Checks running version and target version for any issues. Failure: Any version mismatch across all nodes
checkOpenFiles Checks each node for the number of open files [sysctl kern.openfiles] and compares that against the number of max open files [sysctl kern.maxfiles]. The check will warn at over 80% of the max and fail at over 90% of the max
checkPSCALE136276 Check for criteria of PSCALE-136276
checkPartitions Checks system partition space
checkPatches Checks for highly recommended patches, on the current version if no target version, or for the target version
checkPerformance Checks cluster performance
checkProcesses Checks for OpenSM master, MCP, isi_mca_dump, and isi_upgrade_d process related issues
checkProtectionLevel Check storage pools protection levels
checkRealACL Checks if Real ACLs are configured / set on /ifs/.ifsvar or ifs/.ifsvar/patch. These should not be set and if they are, it would cause an issue for upgrades / installs
checkRemoteSupport Checks is Restricted Shell is enabled and isi_supportassist, if both are enabled and you upgrade to 9.7 then it will cause an issue for support assist services to restart.
checkRoutingTables Displays routing table for each node
checkSBR8000 Checks if SBR is enabled pre-upgrade for OneFS upgrades targeting 8.0.0.0/1
checkSNMPDConfig Checks both SNMPD.config and also isilon_serial_number to make sure they are not 0 bytes
checkSPNs Displays a list of SPNs, only useful when run with --extra
checkSRS Checks the remote connectivity configuration for issues
checkSSHDConfig Checks the /etc/mcp/templates/sshd_config files for known issues
checkSWIFTAccounts checks for SWIFT accounts which is then used to set prioirity of flag when SWIFT is licensed and an upgrade to 9.5 or higher is being performed
checkServices Checks common services to make sure they are in the expected states
checkServicesMonitoring Checks that enabled services are being monitored
checkSmartConnect Check that the SmartConnect Service IPs are all assigned and not being used for client connectivity
checkSnapshot Checks if the Snapshot count is approaching cluster limit of 20,000, whether Autodelete is set to yes, and checks snapshot logs. Checks snapshot logs for EIN/EIO/EDEADLK/Failed to create snapshot
checkStaticRouteConflict Checks for conflicting static routes
checkStoragePools Check storage pools for health/capacity/unprovisioned drive issues
checkSupportability Checks cluster hardware and software supportability
checkSwitchCompatibility Checks backend Dell switches to confirm they are at least version 10.5.0.6
checkSymLink Checks is /var/patch/catalog or /var/patch/tmp are Sym Linked or if catalog is a file instead of directory.
checkSyncIQ Gathers source and target SyncIQ information and reports partners of SyncIQ. Checks for an issue where having a large number of SyncIQ report files causes a tar process to delay other upgrade processes potentially leaving the cluster in a temporary DU scenario for an extended period of time
checkSystemFlag checks for diskpools with system flag set
checkTimeDrift Checks time drift between nodes
checkTimeSync Checks if the cluster is enabled to sync to an external server
checkTimeZone Checks for missing time zone in target OneFS code level
checkUIDGID Checks for UID/GID values greater than 262143 for files located in / and /var
checkUpgrade Checks for in progress upgrade related issues. Warns if the isi_upgrade_d service is enabled. Fails if not in a committed state. Fails if an upgrade activity is already in progress.Checks the fs_fmt_version, an odd or zero fs_fmt_version is problematic
checkUpgradeAgentPort Checks the port used by the isi_upgrade_agent_d daemon to ensure it is not in use by other processes
checkUpgradePath Checks where multiple jumps are required and provides specifics required
checkUptime Checks node uptime, warning over 200 days, flags uptime ETAs
checkVaultCard Checks for the presence of the M.2 vault card in Generation 6 nodes and confirms SMART status threshold has not been exceeded on that device
checkZoneLocalAuth For upgrades to OneFS 8.2 and later, checks if local providers are associated with other access zones