Omitir para ir al contenido principal
Cerrar

Bienvenido a Dell

Mi cuenta
  • Hacer pedidos rápida y fácilmente
  • Ver pedidos y realizar seguimiento al estado del envío
  • Cree y acceda a una lista de sus productos
Iniciar sesión Crear una cuenta Clientes Premier Iniciar sesión en el programa para partners
Contáctenos

How to create Link Aggregation Groups (LAGs) on Dell Networking EMC OS9 Switches

Resumen: How to set up LAG on Dell Force10 switch, How to set up port channel on Dell switch, How to configure link aggregation on Dell Force10 switch

Este artículo se aplica a Este artículo no se aplica a Este artículo no está vinculado a ningún producto específico. No se identifican todas las versiones del producto en este artículo.
Consulte estos recursos

Instrucciones


This article explains how Link Aggregation Groups (LAGs) are implemented on Dell Networking Force10 Switches.

 

Options for LAG type

 

  • Static
  • Link Aggregation Control Protocol (LACP)


Example of Static LAG


 

Command

Purpose

ftos#configure

Enter configuration mode.

ftos(conf)#interface port-channel 1

Define the port-channel number.

ftos(conf-if-po-1)#channel member te 0/1 - 4

Set the range of physical ports needed in the port channel.  Command requires a space between the numbers and hyphen.

ftos(conf-if-po-1)#no shutdown

Set Admin mode to up on the port channel.


 

Example of LACP LAG



LACP Modes

 

  • Active -- In this state, the interface is said to be in the "active negotiating state." LACP runs on any link that is configured to be in this state. A port in Active state automatically initiates negotiations with other ports by initiating LACP packets.
  • Passive -- Passive — In this state, the interface is not in an active negotiating state, but LACP runs on the link. A port in Passive state responds to negotiation requests from ports in Active state. Ports in Passive state respond to LACP packets.

     

Command

Purpose

ftos# configure

Enter configuration mode.

ftos(conf)# interface range te 0/1 - 4

Enter the range of physical ports needed for the port channel.  Command requires a space between the numbers and hyphen.

ftos(conf-inf-range-gi0/0-3)# no shutdown

Set Admin mode to up on the port.

ftos(conf-inf-range-gi0/0-3)# port-channel-protocol lacp

Enter port channel protocol type LACP.

ftos(conf-inf-range-gi0/0-3-lacp)#port-channel 1 mode [active | passive]

Define the port-channel number and mode.


 

Verification & Monitoring commands


 

Command

Purpose

ftos#show interfaces port-channel brief

Shows abbreviated details of all port channels configured.

ftos#show lacp 1

Shows details of specific port channel in LACP mode.

ftos#show interfaces port-channel 1

Shows details of specified port channel interface.



 

Configuration options provided are validated using firmware version 9.4.0.0. Depending on the firmware version installed you may see slight differences in the command options.

 

Productos afectados

Force10 MXL Blade, Force10 S25-01-GE-24P, Force10 S25-01-GE-24T, Force10 S25-01-GE-24V, Force10 S50-01-GE-48T-V, Force10 S50-01-GE-48T, PowerSwitch S4810P, Force10 S50P, Force10 S55T, Force10 S60-44T
Propiedades del artículo
Número del artículo: 000121874
Tipo de artículo: How To
Última modificación: 21 feb. 2021
Versión:  3
Encuentre respuestas a sus preguntas de otros usuarios de Dell
Servicios de soporte
Compruebe si el dispositivo está cubierto por los servicios de soporte.