Omitir para ir al contenido principal
Cerrar

Bienvenido a Dell

Mi cuenta
  • Hacer pedidos rápida y fácilmente
  • Ver pedidos y realizar seguimiento al estado del envío
  • Cree y acceda a una lista de sus productos
Iniciar sesión Crear una cuenta Clientes Premier Iniciar sesión en el programa para partners
Contáctenos

Latitude E5440 CRU (Customer Replaceable Units) Part Removal Guide

Resumen: This article provides a Part Removal Guide for the Dell Latitude E5440

Este artículo se aplica a Este artículo no se aplica a Este artículo no está vinculado a ningún producto específico. No se identifican todas las versiones del producto en este artículo.
Consulte estos recursos

Síntomas

This guide will take you step by step through the safe removal of what are considered to be the Customer Replaceable Unit (CRU) parts of a Dell Latitude E5440.

Table of Contents:

  1. CRU Removal Guide
  2. Removal Instructions

1. Removal Guide

CRUs (Customer Replaceable Units) are the parts of the system that shouldn't need an engineer to remove or replace. This guide includes pictures to reference the processes involved.

If this guide does not cover the part that you need to remove, then you will need to reference your System Manual.

The article below provides information on safe practises to take into consideration before working with electrical equipment.

Back to Top

2. Removal Instructions

 

|

 

SLN291064_en_US__1ReqTools_E7450_BKeith_01

1 Small Phillip's head screwdriver 2 Plastic Scribe
3 Small Flat head screwdriver    

 

SLN291064_en_US__2icon Note : Be aware that using a large Phillips or Flat Head screwdriver may result in damage to the head of the screws. This would make their removal impossible without speciality tools, that aren't available to our onsite engineers.

  1. Pre-Removal Instructions Before removing the Battery:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

  2. Establishing image

SLN291064_en_US__31397725075079.bat2

  1. Slide the battery latches to the side until the red labels are visible.

SLN291064_en_US__41397725098110.bat3

  1. Slide out the battery one side at a time until it disconnects from its connection.

SLN291064_en_US__51397725136656.bat4

  1. Complete

SLN291064_en_US__61397725159436.bat5

 

  1. Pre-Removal Instructions Before removing the SD Card:

    1. During installation or removal of any hardware always ensure all data is backed up properly

  2. Establishing image.

SLN291064_en_US__71397725270371.sd2

  1. Press in the SD memory card and release

SLN291064_en_US__81397725292074.sd3

  1. Slide the SD memory card out of the system

SLN291064_en_US__91397725313917.sd4

  1. Complete.

SLN291064_en_US__101397725328151.sd5

 

  1. Pre-Removal Instructions Before removing the Express Card :

    1. During installation or removal of any hardware always ensure all data is backed up properly

  2. Establishing image.

SLN291064_en_US__111397725350322.ex2

  1. Press in on the Express Card until it is released automatically

SLN291064_en_US__121397725365150.ex3

  1. Pull out the Express Card from the system and remove

SLN291064_en_US__131397725380946.ex4

  1. Complete

SLN291064_en_US__141397725397212.ex5

 

  1. Pre-Removal Instructions Before removing the Bottom Cover :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Remove the Battery, SD Card and Express card

  2. Establishing image.

SLN291064_en_US__151397725414070.bc2

  1. Remove the 5 screws from the bottom base

SLN291064_en_US__161397725513912.bc3

  1. Use the scribe to pry from the inner part of the battery compartment

SLN291064_en_US__171397725542958.bc4

  1. Remove the bottom base/ door

SLN291064_en_US__181397725477053.bc5

  1. Complete

SLN291064_en_US__191397725576051.bc6

 

  1. Pre-Removal Instructions Before removing the Optical Drive:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Remove the Battery, SD Card, Express card and Bottom Cover

  2. Establishing image.

SLN291064_en_US__201397731075082.od2

  1. Remove the single screw

SLN291064_en_US__211397731091831.od3

  1. Use a plastic scribe and push the drive out from the chassis from the screw compartment

SLN291064_en_US__221397731113081.od4

  1. Slide the Optical Drive out and remove

SLN291064_en_US__231397731261061.od5

  1. Remove the two screws securing the ODD bracket

SLN291064_en_US__241397731278998.od6

  1. Remove the ODD bracket

SLN291064_en_US__251397731301014.od7

  1. Use a pin to manually release the drive tray

SLN291064_en_US__261397731318888.od8

  1. Release a tab on the bottom right of the drive to release the bezel

SLN291064_en_US__271397731352075.od9

  1. Remove the bezel

SLN291064_en_US__281397731433213.od10

  1. Complete

SLN291064_en_US__291397731446588.od11

 

  1. Pre-Removal Instructions Before removing the Hard Drive :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Remove the Battery, SD Card, Express card and Bottom Cover

  2. Establishing image.

SLN291064_en_US__301397731475384.hd2

  1. Remove the two screws from the metal holder

SLN291064_en_US__311397731490790.hd3

  1. Lift up the metal holder using a plastic scribe

SLN291064_en_US__321397731508430.hd4

  1. Loosen the hard drive from its connection by pulling the plastic tab

SLN291064_en_US__331397731526695.hd5

  1. Lift up the hard drive

SLN291064_en_US__341397731544195.hd6

  1. Remove the two isolation rubbers from the hard drive

SLN291064_en_US__351397731574881.hd7

  1. Complete.

SLN291064_en_US__361397731591240.hd8

 

  1. Pre-Removal Instructions Before removing the Memory :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Remove the Battery, SD Card, Express card and Bottom Cover

  2. Establishing image.

SLN291064_en_US__371397731638005.mem2

  1. Release the pins that are holding down the memory

SLN291064_en_US__381397731653770.mem3

  1. Remove the memory from its slot

SLN291064_en_US__391397731668488.mem4

  1. Repeat steps 3 and 4 for any additional memory

SLN291064_en_US__401397731742174.mem5

 

  1. Pre-Removal Instructions Before removing the WLAN Card:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Remove the Battery, SD Card, Express card and Bottom Cover

  2. Establishing image.

SLN291064_en_US__411397741128168.wlan2

  1. Remove the antennas from the WLAN card

SLN291064_en_US__421397741143668.wlan3

  1. Remove the single screw securing the WLAN Card

SLN291064_en_US__431397741160777.wlan4

  1. Remove the WLAN card from its slot

SLN291064_en_US__441397741200026.wlan5

  1. Complete.

SLN291064_en_US__451397741222963.wlan6

 

  1. Pre-Removal Instructions Before removing the WWAN Card:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Remove the Battery, SD Card, Express card and Bottom Cover

  2. Establishing image.

SLN291064_en_US__461397741242962.ww2

  1. Remove the antennas from the WWAN card

SLN291064_en_US__471397741299039.ww3

  1. Remove the single screw from the card

SLN291064_en_US__481397741323194.ww4

  1. Remove the WWAN card from its slot

SLN291064_en_US__491397741339475.ww5

  1. Complete

SLN291064_en_US__501397741365521.ww6

 

  1. Pre-Removal Instructions Before removing the Coin-cell Battery:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Remove the Battery, SD Card, Express card and Bottom Cover

  2. Establishing image.

SLN291064_en_US__511397731769111.coin2

  1. Carefully unplug the coin cell battery cable

SLN291064_en_US__521397731791485.coin3

  1. Remove the coin cell battery

SLN291064_en_US__531397731810360.coin4

  1. Complete.

SLN291064_en_US__541397731865124.coin5

 

  1. Pre-Removal Instructions Before removing the Keyboard Bezel:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Battery

  2. Establishing image.

SLN291064_en_US__551397741424129.bz2

  1. Use a plastic scribe to gently pry the bezel away from the top left corner and unhook it from the securing tabs

SLN291064_en_US__561397741473628.bz3

  1. Remove the bezel

SLN291064_en_US__571397741499424.bz4

  1. Complete.

SLN291064_en_US__581397741542533.bz5

 

  1. Pre-Removal Instructions Before removing the Keyboard:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Battery and Keyboard Bezel

  2. Establishing image.

SLN291064_en_US__591397741574126.ky2

  1. Remove the 2 screws that are holding down the keyboard

SLN291064_en_US__601397741616281.ky3

  1. Remove 2 screws that are securing the keyboard

SLN291064_en_US__611397741728028.ky4

  1. Gently pry the edges of the keyboard at the sides with a plastic scribe
    to unhook it from the securing tabs and lift up the keyboard.

SLN291064_en_US__621397741745559.ky5

  1. Unplug the flex cable

SLN291064_en_US__631397741777183.ky6

  1. Remove the keyboard

SLN291064_en_US__641397741829306.ky7

  1. Complete

SLN291064_en_US__651397741902930.ky8

 

If you require further assistance, please contact Technical Support

 

  Contact Us  

Productos afectados

Latitude E5440
Propiedades del artículo
Número del artículo: 000132952
Tipo de artículo: Solution
Última modificación: 10 abr 2021
Versión:  4
Encuentre respuestas a sus preguntas de otros usuarios de Dell
Servicios de soporte
Compruebe si el dispositivo está cubierto por los servicios de soporte.