Omitir para ir al contenido principal
Cerrar

Bienvenido a Dell

Mi cuenta
  • Hacer pedidos rápida y fácilmente
  • Ver pedidos y realizar seguimiento al estado del envío
  • Cree y acceda a una lista de sus productos
  • Administre sus sitios, productos y contactos de nivel de producto de Dell EMC con Administración de la empresa.
Iniciar sesión Crear una cuenta Clientes Premier Iniciar sesión en el programa para partners
Contáctenos

Número del artículo: 000125761

Latitude 5491 Teardown removal guide for customer replaceable units (CRUs)

Resumen: This article is a guide to the parts of the Latitude 5491 notebook that Dell considers it easy for anyone to remove and replace themselves.

Contenido del artículo

Síntomas

These guides take you step-by-step through the safe removal of the Customer Replaceable Unit (CRU) parts of a Latitude 14 5491 notebook system. (CRUs are the parts of the system that do not need an engineer to remove or replace.) The guides include pictures referencing what is involved.

Table of Contents:

  1. CRU Removal Guide
  2. Removal Instructions

 

Removal Guide

 

If these guides do not cover what you are looking to do, then you will want to reference your System Manual.

The article below provides information about safe practices to consider before working with electrical equipment.


Back to Top

Causa

N/A

Resolución

 

Removal Instructions

 

SLN310356_en_US__1icon Note: Click the title of the section you want to open below, in order to see the contents.
 
|

 

SLN310356_en_US__2ReqTools_E7450_BKeith_01

1 Small Phillip's head screwdriver 2 Plastic Scribe
3 Small Flat head screwdriver    
 
SLN310356_en_US__1icon Note: Be aware that using a large Phillips or Flat Head screwdriver may result in damage to the head of the screws. This would make their removal impossible without specialty tools, that are not available to our onsite engineers.

 

  1. Pre-Removal instructions before removing the Main Access Panel:

    1. During installation or removal of any hardware always ensures that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

  2. Loosen the eight (8) captive screws that secure the cover to the chassis [1].

SLN310356_en_US__45491_Cover_BK_01

  1. Using a plastic scribe or similar tool, pry the base cover up from the top edge of the system. Continue around the cover to release it from the chassis. [2]

  2. Lift the cover up and off the chassis.

SLN310356_en_US__55491_Cover_BK_02

 

  1. Pre-Removal instructions before removing the Battery:

    1. During installation or removal of any hardware always ensures that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the System Cover.

  2. Disconnect the battery cable from the motherboard and remove the cable from the routing channel. [1]

  3. Loosen the captive screw on the side of the battery closest to the right-hand side of the chassis. [2]

SLN310356_en_US__65491_Battery_BK_01

  1. Lift the Battery up and out of the system [3].

 

  1. Pre-Removal instructions before removing the Keyboard Trim:

    1. During installation or removal of any hardware always ensures that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the System Cover, and Battery

  2. Using a plastic scribe or similar tool, pry up the trim starting at the access points [1]. Continue around the trim going in a clockwise direction. Lift up from the right-hand side [2] to remove from the system.

SLN310356_en_US__75491_Keyboard_BK_01

 

  1. Pre-Removal instructions before removing the Keyboard:

    1. During installation or removal of any hardware always ensures that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the System Cover, Battery, and Keyboard Trim.

  2. Lift the latch and remove the keyboard cable from the connector [1].

  3. Lift the latch and remove the other keyboard cables from the connectors [2,3,4].

SLN310356_en_US__85491_Keyboard_BK_02

SLN310356_en_US__1icon Note: The number of keyboard cables depends on the type of keyboard you ordered.

  1. Turn the system back onto its base and open the system up. Remove the five (5) screws that secure the keyboard to the chassis [1].

  2. Using a plastic scribe, pry the keyboard up from the bottom and lift it up out of the system [2].

SLN310356_en_US__105491_Keyboard_BK_03

  1. Be careful removing the keyboard from the system as you will need to pull the keyboard cables through from the rear of the system.

SLN310356_en_US__115491_Keyboard_BK_04

 

  1. Pre-Removal instructions before removing the Memory:

    1. During installation or removal of any hardware always ensures that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the System Cover, and Battery.

  2. Pull the metal clips on the short sides of the memory dimm apart, until the module pops up at an angle to the connector [1].

  3. Lift the memory dimm out of the system [2].

SLN310356_en_US__125491_Memory_BK_01

SLN310356_en_US__1icon Note: Please repeat Steps 2 and 3 for any additional Memory DIMMs located in the system.

 

  1. Pre-Removal instructions before removing the Solid State Drive (SSD):

    1. During installation or removal of any hardware always ensures that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the System Cover, and Battery.

  2. Peel off the adhesive mylar shield from on top of the SSD [1].

SLN310356_en_US__1icon Note: Be careful with this adhesive shield, you will need to put it back on when the replacement drive is fitted.

  1. Remove the screw that secures the end of the SSD to the motherboard [2]. Lift the card to a 35-degree angle and remove from the connector [3].

SLN310356_en_US__155491_SSD_BK_01

SLN310356_en_US__1icon Note: This applies only to the SATA M.2 2280 version of the SSD.

  1. Once the card is removed, you can remove the SSD frame by removing the securing screw that holds it to the system [1].

SLN310356_en_US__175491_SSD_BK_02

  1. Lift the frame out of the system [2].

 

  1. Pre-Removal instructions before removing the Hard Disk Drive (HDD):

    1. During installation or removal of any hardware always ensures that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the System Cover, and Battery.

  2. Disconnect the HDD cable from the connector on the motherboard [1], and remove the four (4) screws that secure the HDD to the chassis [2].

SLN310356_en_US__185491_HHD_BK_01(1)

  1. Lift the drive out of the system.

SLN310356_en_US__195491_HHD_BK_02

Latitude 5491 Hard Drive Removal - Duration 1:18 - English Only

 

  1. Pre-Removal instructions before removing the Coin Cell Battery:

    1. During installation or removal of any hardware always ensures that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the System Cover, and Battery.

  2. Disconnect the coin cell battery cable from the connector on the motherboard [1]. Lift the coin cell battery up and away from the adhesive holding it to the motherboard [2].

SLN310356_en_US__205491_Coin_BK_01

 

  1. Pre-Removal instructions before removing the WLAN Card (WiFi, Wireless):

    1. During installation or removal of any hardware always ensures that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the System Cover, and Battery.

  2. Remove the screw that secures the card to the system [1]. Remove the bracket that secures the antenna cables [2] and disconnect the antenna cables from the WLAN card [3].

SLN310356_en_US__215491_WLAN_BK_01

SLN310356_en_US__1icon Note: Remove the wireless card from the system. Make sure the adhesive pad under the card stays on the system board and/or chassis frame during the removal process.

  1. Lift the card out of the connector and the system [4].

 

  1. Pre-Removal instructions before removing the WWAN CARD (3G, Cellular):

    1. During installation or removal of any hardware always ensures that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the System Cover, and Battery.

  2. Remove the screw that secures the card to the system [1]. Remove the bracket that secures the antenna cables [2] and disconnect the antenna cables from the WWAN card [3].

SLN310356_en_US__235491_WWAN_BK_01

  1. Lift the card out of the connector and the system [4].

 

  1. Pre-Removal instructions before removing the SD Memory Card:

    1. During installation or removal of any hardware always ensures that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

  2. You have to push in on the SD card in order for it to pop out of the system [1]. Once it pops out - you can grip it and pull it all the way out of the system [2].

SLN310356_en_US__245491_SD_BK_01

SLN310356_en_US__255491_SD_BK_02

 

  1. Pre-Removal instructions before removing the SIM Card:

    1. During installation or removal of any hardware always ensures that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

  2. Insert a straightened paper clip or the SIM card removal tool into the pinhole on the SIM card tray [1].

  3. Pull on the SIM card tray when it pops out of the side of the system [2].

SLN310356_en_US__265491_SIM_BK_01

  1. Remove the SIM card from the tray and push the empty tray into the slot until it clicks in place.

 

If you require further assistance, please contact Technical Support.

 

  Contact Us  

Propiedades del artículo

Producto comprometido

Latitude 5491

Fecha de la última publicación

23 may 2024

Versión

5

Tipo de artículo

Solution

Volver al principio