Omitir para ir al contenido principal
Cerrar

Bienvenido a Dell

Mi cuenta
  • Hacer pedidos rápida y fácilmente
  • Ver pedidos y realizar seguimiento al estado del envío
  • Cree y acceda a una lista de sus productos
Iniciar sesión Crear una cuenta Clientes Premier Iniciar sesión en el programa para partners

Precision 7920 Rack Teardown Removal Guide for Customer Replaceable Units (CRUs)

Resumen: This article is a removal guide to the parts of a Precision 7920 Rack workstation that are OK for anyone to remove and replace.

Este artículo se aplica a Este artículo no se aplica a Este artículo no está vinculado a ningún producto específico. No se identifican todas las versiones del producto en este artículo.
Consulte estos recursos

Síntomas

These guides take you step by step through the safe removal of the customer replaceable unit (CRU) parts of a Precision 7920 Rack workstation. CRUs are the parts of the computer that should not need an engineer to remove or replace. The guides also include figures to reference what is involved.

Causa

Not applicable

Resolución

Table of Contents:

  1. CRU Removal Guide
  2. Removal Instructions

 

Removal Guide

 

If these guides do not cover what you are looking to do, then reference your System Manual.

The article below provides information about safe practices to consider before working with electrical equipment.


Back to Top

 

Removal Instructions

 

Note: Click the title of the section that you want to open below, in order to see the contents.
 
|

 

Recommended tools

1 Small Phillips head screwdriver 2 Plastic scribe
3 Small flat-head screwdriver    
 
Note: Using a large Phillips or flat-head screwdriver may result in damage to the head of the screws. This would make their removal impossible without specialty tools that are not available to our onsite engineers.
 

 

  1. Pre-removal instructions before removing the power supply unit:

    1. During installation or removal of any hardware, always ensure that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets (for example, the external main power cable).

  2. Press the PSU release latch [1] and using the handle, pull the power supply out of the computer [2].

Removing the power supply

 

  1. Pre-removal instructions before removing the top cover:

    1. During installation or removal of any hardware, always ensure that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

  2. Pull up on the Latch at the front of the cover [1] and push the cover towards the rear of the computer [2].

Removing the top cover

  1. Lift the cover up and away from the computer [3].

Note: The computer shuts down if the cover is removed before shutting down the computer.

 

  1. Pre-removal instructions before removing the front bezel:

    1. During installation or removal of any hardware, always ensure that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

  2. Locate [1] and unlock [2] the bezel using the bezel key. Press the release button on the left side of the bezel [3] and swing the bezel towards the right side to unhook that end [4] and remove from the computer.

Removing the front bezel

  1. Pre-removal instructions before removing the hard drive blanking plate:

    1. During installation or removal of any hardware, always ensure that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the front bezel.

  2. Press the release button on the front of the blanking plate and pull it out of the front of the computer.

Removing the hard drive blanking plate

Note: The hard drive blanking plates are required to ensure proper cooling flow in the computer. Only remove this plate if you are fitting a hard drive in that slot.

  1. Pre-removal instructions before removing the power supply unit blanking plate:

    1. During installation or removal of any hardware, always ensure that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

  2. Pull the blanking plate out of the rear of the computer.

Removing the power supply unit blanking plate

Note: The power supply unit blanking plate is required to ensure proper cooling flow in the computer. Only remove this plate if you are fitting a second power supply unit.

 

  1. Pre-removal instructions before removing the air shroud:

    1. During installation or removal of any hardware, always ensure that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the Top Cover.

  2. If installed remove any full-length PCIe cards or graphics cards from the computer.

  3. Lift the shroud up and out of the computer.

Removing the air shroud

  1. Pre-removal instructions before removing the system fan:

    1. During installation or removal of any hardware, always ensure that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the Top Cover and air shroud.

  2. Press in the release tab and pull the fan out of the assembly bracket.

Removing the system fan

Note: While the fans are hot swappable, opening the system cover causes the computer to shut down. We recommend for proper cooking, that you only swap one fan at one time.

  1. Pre-removal instructions before removing the fan assembly:

    1. During installation or removal of any hardware, always ensure that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the Top Cover and air shroud.

  2. Lift the blue release latches on either side of the bracket [1]. Grip the latches and pull the assembly up and out of the computer [2].

Removing the fan assembly

 

  1. Pre-removal instructions before removing the memory:

    1. During installation or removal of any hardware, always ensure that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the Top Cover and the Air Shroud.

Warning: Power off the computer and allow the memory modules to cool before handling the memory. Stay away from the metal contacts on the bottom of the memory modules.

  1. Pull the securing clips away from the memory.

Pulling the memory securing clips

  1. Lift the memory up and out of the slot.

Removing the memory

Note: Repeat steps 2 & 3 for any additional memory in the computer.
 
Note: Memory module blanks should be installed in any empty sockets to ensure proper cooling in the computer.

 

  1. Pre-removal instructions before removing the hard disk drive caddy:

    1. During installation or removal of any hardware, always ensure that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the Front Bezel.

  2. Press the release button [1] on the front of the caddy to release the latch. Open the latch [2] and pull the drive out of the front of the computer.

Removing the hard disk drive caddy

  1. Pre-removal instructions before removing the hard disk drive 3.5" bracket:

    1. During installation or removal of any hardware, always ensure that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the hard drive Caddy from the computer.

  2. Remove the four screws that secure the hard drive to the bracket.

Removing the hard disk drive 3.5" bracket

  1. Pre-removal instructions before removing the hard disk drive 3.5" to 2.5" conversion bracket:

    1. During installation or removal of any hardware, always ensure that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the hard drive caddy from the computer.

  2. Remove the five screws that secure the 2.5" hard drive to the 3.5" bracket and lift the drive out of the bracket.

Removing the 2.5" hard drive from the bracket

  1. Remove the two screws that secure the 2.5" converter block to the 2.5" hard drive and remove the hard drive.

Removing the converter block from the 2.5" hard drive

  1. Pre-removal instructions before removing the slim line optical disc drive:

    1. During installation or removal of any hardware, always ensure that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the Top Cover and Front Bezel.

  2. Disconnect the optical drive cable from the optical drive [1], press the blue latch [2] and push the drive out the front of the chassis [3].

Removing the optical drive

 

  1. Pre-removal instructions before removing the expansion cards:

    1. During installation or removal of any hardware, always ensure that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the Top Cover and Air Shroud if it is getting in your way.

  2. Lift the expansion card latch out of the slot [1], check for any card catches and pull the card until it disengages from the riser slot [2].

Riser 1 Expansion Slots

Riser 2 Expansion Slots

Riser 3 Expansion Slots

Note: Some expansion cards require extra power to run correctly. This is usually with an extra power or fan cable. Some types of graphics cards include a locking latch at the back of the card where is secured to the slot in the motherboard.

  1. Before installing or removing any full-length PCIe cards, the PCIe holder must be open. Press down on the release latch to open it [1]. Rotate the latch until it locks in place to close it.

Opening the PCIe holder

 

  1. Pre-removal instructions before removing the PCIe risers:

    1. During installation or removal of any hardware, always ensure that all data is backed up properly.

    2. Disconnect any telephone, network, or USB cables from the computer.

    3. Disconnect the computer and all attached devices from their electrical outlets.

    4. Remove the Top Cover, Air Shroud, and any Expansion Cards.

Note: Before you start, you must check if any expansion cards are installed. If so, you must remove these cards before you begin.
 

  1. Disconnect any cables to Riser 1, pull the expansion card latch out of the slot and pushing in on the blue locking tabs lift the riser up and out of the computer.

Removing the PCIe riser 1 card

  1. Disconnect any cables to Riser 2, pull the expansion card latch out of the slot and loosen the four screws [1 and 2] securing the riser to the chassis, press the release tab [3] and lift the riser up and out of the computer [4].

Removing the PCIe riser 2 card

  1. Disconnect any cables to Riser 3, pull the expansion card latch [1], loosen the thumbscrew [2] that secures the riser to the chassis, and lift the riser up and out of the slot in the motherboard [3].

Removing the PCIe riser 3 card

 
If you require further assistance, contact Technical Support.
  Contact Us  
 

Productos afectados

Precision 7920 Rack
Propiedades del artículo
Número del artículo: 000143946
Tipo de artículo: Solution
Última modificación: 10 jul 2023
Versión:  5
Encuentre respuestas a sus preguntas de otros usuarios de Dell
Servicios de soporte
Compruebe si el dispositivo está cubierto por los servicios de soporte.