Skip to main content
Sign Out

Welcome to Dell

My Account
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Create and access a list of your products
Sign In Create an Account Premier Sign In Partner Program Sign In
Contact Us

Dell P3424WEB Monitor Usage and Troubleshooting Guide

Summary: This article provides information about how to set up and use the Dell P3424WEB Curved Video Conferencing Monitor. Learn how to troubleshoot common display or video issues with the Dell P3424WEB monitor. ...

This article applies to   This article does not apply to 
Check out resources for

Instructions

Dell P3424WEB Monitor

Quick Links

Getting Started with your Dell P3424WEB Monitor Dell P3424WEB Monitor Setup, Specifications, and Service Manual Dell Drivers & Downloads Warranty and Support Services Frequently Asked Questions
|

The Dell P3424WEB monitor has an active matrix, Thin-Film Transistor (TFT), Liquid Crystal Display (LCD), and LED backlight. The monitor features include:

  • 86.71 cm (34.14 in.) active area display (measured diagonally) 3440 x 1440 (21:9) resolution, plus full-screen support for lower resolutions.
  • Wide viewing angles with 99% sRGB color.
  • Tilt, swivel, and vertical extension adjustment capabilities.
  • Integrated speakers (2 x 5 W)
  • Removable pedestal stand and Video Electronics Standards Association (VESA) 100 mm mounting holes for flexible mounting solutions
  • Ultrathin bezel minimizes the bezel gap during multimonitor usage, enabling easier setup with an elegant viewing experience.
  • Extensive digital connectivity with DP helps future-proof your monitor.
  • Single USB Type-C to supply power to a compatible laptop while receiving a video signal.
  • USB-C and RJ45 ports enable a single-cable, network-connected experience.
  • Plug-and-play capability if supported by your computer.
  • On-Screen Display (OSD) adjustments for ease of set-up and screen optimization
  • Power and OSD buttons lock.
  • Security lock slot
  • Stand lock.
  • Supports Picture by Picture (PBP)/Picture in Picture(PIP) Select mode
  • Allows users to switch USB KVM functions in PBP/PIP mode.
  • The monitor is designed with the Dell Power Button Sync (DPBS) feature to control the personal computer system power state from the monitor power button.*
  • Premium Panel Exchange for peace of mind
  • Optimize eye comfort with a flicker-free screen and ComfortView Plus feature.
  • This monitor uses a low blue light panel. When the monitor is reset to factory settings or default setting (Preset mode: Standard), it works in compliance with TUV Rheinland (hardware solutions provider).
  • Decreases the level of hazardous blue light emitted from the screen to make viewing more comfortable for your eyes
  • The monitor adopts Flicker-Free technology, which clears the eye-visible flicker, brings a comfortable viewing experience, and prevents users from suffering eye strain and fatigue.
  • Certified for Microsoft Teams and Zoom.
  • Certified for Windows Hello (Face Authentication) and supports Microsoft Cortana.
  • Extra customization using Dell Peripheral Manager/Dell Display Manager (DDM) for the Windows operating system and Dell Display and Peripheral Manager (DDPM) for the Mac operating system

* The Dell system that supports DPBS is listed on the Dell website. DPBS function can be enabled in the OSD menu under Display.

WARNING: The possible long-term effects of blue light emission from the monitor may damage your eyes, including eye fatigue or digital eye strain. The ComfortView feature is designed to reduce the amount of blue light emitted from the monitor to optimize eye comfort.

This section provides some technical specifications of the Dell P3424WEB monitor. For more information, see the user manual of the Dell P3424WEB monitor.

Table 1: Technical specifications of the Dell P3424WEB monitor
Ports and connectors
  • 1 x DP 1.2 (HDCP 2.2)
  • 1 x HDMI 2.1 (TMDS)3
  • 1 x USB Type-B (USB 3.2 Gen1 upstream port)
  • 1 x USB Type-C (Alternate mode with DisplayPort 1.2, USB 3.2 Gen1 upstream port, Power Delivery PD up to 90 W)
  • 1 x USB Type-C downstream (15 W), USB 3.2 Gen1 (5 Gbps)
  • 2 x super speed USB 5 Gbps (USB 3.2 Gen1)
  • 1 x super speed USB 5 Gbps (USB 3.2 Gen1) with BC 1.2 charging capability at 2 A (max)
  • 1 x 3.5 mm headphone jack
  • 1 x RJ45
Any other ports
  • Security lock slot (based on Kensington Security Slot)
  • Power connector

For the best viewing experience, assemble the monitor stand, connect and organize the cables, and set up the monitor ergonomically.

Attaching the stand

The standard monitor stand is detached when it is shipped from the factory. To learn how to attach the standard monitor stand, see the user manual of the Dell P3424WEB monitor.

To learn how to set up any other monitor stand or monitor arm, see the setup guide of the product.

CAUTION: Do not remove the monitor from the packaging box before attaching the stand.

Ergonomics

Where you put your monitor is almost as important as what model you buy.

  • The monitor must be directly in front of you, at an arm’s length away (between 20-40 inches from your eyes).
  • The top edge of the screen must be set at eye level when you are sitting comfortably. Adjust your chair height or the height of the monitor to achieve this.

Connecting your monitor to the computer

To connect your Dell P3424WEB monitor to your computer:

WARNING: Read and follow Safety Precautions When Working with Electronic and Electrical Equipment.
NOTE: Dell P3424WEB supports display over USB-C port with Alternate mode DP 1.2.
  1. Turn off the computer.
  2. Connect the power cable to the monitor.
  3. Connect the video cable (USB-C, DisplayPort, or HDMI) between the computer and the monitor.
    NOTE: Setting up the monitor with a Dell docking station? Learn How to Connect and Set Up a Docking Station With a Dell Laptop.
    NOTE: Setting up more than one monitor? Learn How to Set up Multiple Monitors or see the user manual of the Dell P3424WEB monitor.
  4. Connect the USB upstream cable between the monitor and the computer (if available).
  5. Turn on the monitor.
  6. Turn on the computer.

For additional product-specific information, see the user manual of the Dell P3424WEB monitor.

CAUTION: Dell P3424WEB setup must comply with the recommended panel orientation and working angle only. Setting up the monitor in an orientation that is not recommended may damage the monitor, cause a safety hazard, or both.
NOTE: The following instructions are applicable only for the stand that was shipped with your monitor. If you are connecting a stand that you purchased from any other source, follow the setup instructions that were included with the stand.

Using the tilt, swivel, and vertical extension

With the stand attached to the monitor, you can tilt the monitor for the most comfortable viewing angle.

Dell P3424WEB tilt, swivel, and vertical extension
Figure 1: Using the tilt, swivel, and vertical extension on the Dell P3424WEB monitor.

NOTE: The stand is detached when the monitor is shipped from the factory.

To access the on-screen display (OSD) menu, press Joystick (Figure 2) at the back of the monitor.

To learn more about navigating through the on-screen display (OSD) menu, see the user manual of the Dell P3424WEB monitor.

NOTE: The monitor automatically saves any changes that you make. Whenever you move to another menu item, exit the OSD menu, or wait for the OSD menu to automatically close.

Using the joystick control

Dell P3424WEB Joystick Control
Figure 2:Joystick Control

To modify the OSD adjustments using the joystick control on the rear end of the monitor, do the following:

  1. Press the joystick to open the OSD Menu Launcher.
  2. Move the joystick up/down/center/left/right to switch between the OSD menu options.

Using the rear-panel controls.

Dell P3424WEB Menu Launcher
Figure 3: Menu Launcher

  • Toggle the Joystick Up to open the Main Menu.
  • Toggle the Joystick Left or Right to select the wanted Shortcut Keys.
  • Toggle the Joystick Down to Exit.

Resetting a monitor to factory defaults can help resolve many video or display-related issues. To reset your Dell P3424WEB monitor to factory default settings:

  1. Press the joystick on the monitor to enter the On-Screen Display (OSD) Menu.
  2. Press up or down on the joystick to highlight the Other option in the menu and press on the joystick to select.
  3. Press up or down to highlight the Factory Reset option in the menu and press on the joystick to select it.
  4. Press the joystick to confirm the reset action.

Dell P3424WEB Joystick Control
Figure 4: Joystick Control

A diagnostic test helps determine if the Dell monitor is normal when faced with a blank screen, blurry image, flickering or other abnormalities.

Verify that the monitor is working correctly by running a diagnostic test if you experience the following symptoms.

  • Your computer does not turn on or show any sign of power.
  • Your computer does not show any indication of activity, the screen is blank and does not display the Dell logo during start-up.
  • Your computer gets stuck at the Dell logo screen or does not respond to any keys during start-up.
  • You cannot see any display on the screen.
  • You hear the windows chime, but the monitor screen is blank.

Self-Test Feature Check

Your Dell P3424WEB monitor provides a self-test feature check that allows you to check if the monitor is functioning properly. When the monitor is connected to the computer but the screen stays dark, run the monitor self-test by following these steps:

  1. Turn off the computer and the monitor.
  2. Unplug the video cable from the back of the computer. To ensure proper self-test operation, disconnect the video cable (VGA, DVI, HDMI, DisplayPort, or USB-C cable) from the back of the computer.
  3. Turn on the monitor. A floating dialog box should appear on-screen (against a black background), if the monitor cannot sense a video signal and is working correctly. While in self-test mode, the power LED remains white. Also, depending upon the selected input, the dialog box scrolls through the screen.
  4. This box also appears during normal system operation, if the video cable becomes disconnected or damaged.
  5. Turn off the monitor and reconnect the video cable.
  6. Turn on the computer and the monitor.

If the screen remains blank, check the video card (GPU) and computer, because the monitor is functioning properly.

Built-In Self-Test or Built-In Diagnostics

Your Dell P3424WEB monitor has an integrated diagnostic tool. Hardware diagnostic helps determine if the screen abnormality issue is with the monitor or the video card on your computer.

If you observe any screen anomalies, you should isolate the monitor by performing the built-in diagnostics (BID).

If you do not detect any screen abnormalities in the diagnostics test, the monitor is functioning properly. Check the video card (GPU) and the computer.

If you notice any abnormalities in the diagnostics test, contact Dell Technical Support for repair options.

During the manufacturing process, it is not uncommon for one or more pixels to get stuck in an unchanging state. Such pixel issues are hard to see and do not affect the display quality or usability. Learn more about Dell Display Pixel Guidelines.

The following table contains information about troubleshooting common display-related issues on your Dell P3424WEB monitor.

Alternatively, learn How to Troubleshoot Display or Video Issues on a Dell Monitor or check our Dell monitor self-help guide.

Table 3: Troubleshooting is common display issues on Dell P3424WEB monitor.
Common Problem What User Experiences Possible Solution
No Video - Power LED Off No picture
  • Connect the power cable securely to the monitor.
  • Verify that the power outlet is functioning properly by using any other electrical equipment.
  • Press the power button.
  • Test with a known-good cable and a known-good computer if possible.
No Video - Power LED On No picture or no brightness
Poor Focus The picture is fuzzy, blurry, or ghosting.
Shaky or Jittery Video Wavy picture or fine movement
Missing Pixels LCD screen has spots.
  • Turn off the monitor and then turn on the monitor after a few minutes.
  • A pixel that is permanently off is a natural defect that can occur in LCD technology.
  • Run the built-in diagnostic (BID) test.
Stuck On/Off Pixels LCD screen has a bright spot.
Brightness Problems Picture too dim or too bright.
Geometric Distortion The screen not centered correctly.
NOTE: When using DisplayPort input, the positioning adjustments are not available.
Horizontal or Vertical Lines The screen has one or more lines.
NOTE: When using DisplayPort input, the positioning adjustments are not available.
Synchronization Problems The screen appears scrambled or torn.
Safety-Related Issues Visible signs of smoke or sparks
Intermittent Problems The monitor malfunctions on and off.
Missing Color The picture does not have color.
Wrong Color The picture color is not good.
Image Retention from a Static Image Left on the Monitor for a Long Period A faint shadow from the static image appears on the screen.
  • Use the Power Management feature to turn off the monitor when it is not in use.
  • Alternatively, use a dynamically changing screensaver.
The screen image is too small. The image is centered on the screen, but does not fill the entire viewing area.
Image Ghosting Fast-moving images leave a trail of shadow images.

On certain videos and applications with fast-moving images, imaging ghosting, which appears as a trailing shadow, may occur.

Change the Response Time to Fast using the On-Screen Display (OSD) menu.
No Input Signal when user controls are pressed. No picture, the power LED light is white.
  • Check the signal source. Ensure that the computer is not in power-saving mode by moving the mouse or pressing any key on the keyboard.
  • Connect the video cable securely between the monitor and the computer.
  • Restart the computer.
The picture does not fill the entire screen. The picture cannot fill the height or width of the screen.
No Video, No Display No video when connecting docking, dongle, or Blu-ray DVD players Because legacy platforms cannot identify or output 3440 x 1440, adjust the EDID to a lower resolution to address this compatibility issue.
  1. Remove all input cables.
  2. Press Button 3 and Button 4 for 5 seconds
  3. Choose Enable on POP up screen to change the maximum resolution from 3440 x 1440 to 3840 x 1080.
Unable to switch back to native resolution (3440 x 1440) after Picture by Picture is turned off.

Dell P3424WEB supports Picture by Picture (PBP) mode. Picture by Picture (PBP) mode is two side-by-side images with each image that is displayed at 2560 x 1440 resolution.

When the monitor is connected to a computer using HDMI and PBP mode is turned off, the monitor may display images at the lower resolution (2560 x 1440) rather than automatically switching to the native resolution (3440 x 1440).
  1. Disconnect the HDMI cable.
  2. Wait for 5-10 seconds.
  3. Connect the HDMI cable.
Display mode changes from Second screen only to Extended mode after opening and closing the laptop LCD.

The display mode on your computer reverts to Duplicate or Extend. This depends on which was selected before you changed to Second screen only or Projector only when you close and open the laptop screen.

When you close and then reopen the lid on a laptop, the Connecting and Configuring Displays (CCD) feature in Windows automatically reverts the display mode to the last active selection. This behavior is by design in Microsoft Windows.

Switch to the display mode that you want after you close and reopen the laptop screen manually:

  1. Press the Windows + P key on the keyboard.
  2. Select Second screen only or Projector only mode.
The monitor blinks twice when connected to computer with an Nvidia NVS 310 video or graphics card.

When the monitor is turned-off and back on, the monitor may blink twice. This issue may occur if the computer is using a Nvidia Graphic NVS 310 card and the graphics card resolution setting is 2560 x 1600.

To resolve this issue, manually set the resolution to 2560 x 1440 using the Nvidia Control Panel.

  1. Right-click the desktop and select Nvidia Control Panel.
  2. In the Nvidia Control Panel, select Change resolution on the left panel.
  3. Under Resolution, select 2560 x 1440.
  4. Click Apply to confirm.
The monitor has a sound icon when Dell P3424WEB is connected to a laptop using HDMI.

Dell P3424WEB does not support audio or sound using HDMI. Speakers or headphones must be connected using the audio connector on the computer.

To resolve the audio icon displaying, update the video or graphics (GPU) driver to the latest version. Learn How to Download and Install Dell Drivers.
The monitor will not display Blu-Ray video after the monitor is powered-off and powered on. If the monitor is powered-off and powered-on when displaying the Blu-Ray video, the Blu-ray player may lose the data signal from the system to the monitor.
  1. Disconnect the HDMI cable
  2. Wait for 5 seconds
  3. Connect the HDMI cable
Cannot enable YCbCr color mode on the monitor. When the monitor is connect to the computer using HDMI, the video or graphics card (GPU) controls the YCbCr setting. Disable the YCbCr setting from the video or graphics utility such as Intel HD Graphics Control Panel.
Monitor will not support the YCbCr color format when a USB-C to HDMI dongle is connected from the monitor to the computer. Some combinations of USB-C to HDMI dongle and video or graphics card (GPU) are not compatible to support the YCbCr color format.
  • Do not use the dongle
  • Connect the computer to the monitor using the HDMI cable or the USB-C cable
  • Disable the YCbCr setting from the video or graphics card (GPU) utility such as Intel HD Graphics Control Panel
When changing the monitor’s resolution from Windows Display Settings, the image quality may not be good. Windows Display Settings and the resolution settings on the laptop's video or graphics utility may not be compatible. Change the resolution using the video or graphics card (GPU) utility such as Intel HD Graphics Control Panel.
No video when the monitor is connected to a Dell docking station. The monitor may not receive video signals from the computer when connected to a Dell docking station. To learn more about how to set up and configure the Dell P3424WEB monitor with a Dell docking station, see the user manual of the Dell P3424WEB monitor.
Light leak from the monitor The monitor appears to have light leak from the edges in a dark room. This is the normal behavior of the monitor. Dell consumer monitors are tested under 150-lux ambient lighting (similar to typical office lighting). Dell UltraSharp and Gaming monitors are tested with tighter criteria of 70-lux ambient lighting (dimly lit room, but not dark). Learn more about Troubleshooting Light Leakage or Light Bleeding on a Dell Monitor or Laptop LCD Screen.
Color variation on the corners of the monitor The monitor appears to have color variation on the corners of the screen.

The optimal viewing position for the monitor is from the center of the screen.

Dell P3424WEB monitor uses a curved IPS panel, the corners of the screen may appear slightly yellowish or pinkish, especially when viewing in a dark room. This is normal IPS panel behavior and typically does not affect the overall viewing performance.

  1. Change the Uniformity Compensation using the On-Screen Display (OSD) menu.
  2. Change the Uniformity compensation setting to Calibrated
No video when a Blu-Ray, DVD player or PS4 is connected to the monitor using HDMI. The monitor does not display any video when an external Blu-ray, DVD player or PS4 is connected.

Dell P3424WEB monitor is factory default set at HDMI EDID with three Block (Detailed Timing Descriptor) to support 3440 x 1440 @ 60 Hz. To display a resolution of 3840 x 1080 @ 60 Hz or lower, you must switch the monitor HDMI EDID from three Block to two Block.

  1. Remove all input cables from the monitor
  2. Press and hold Button 3 and Button 4 for 5 seconds
  3. A message box appears. Select Enable to switch to the lower primary resolution

To display 3440 x 1440 resolution over HDMI again, you must switch the monitor back to HDMI EDID 3 Block. Follow Steps 1 and 2, and select Disable.
Horizontal stripes when watching online videos using Microsoft Movies and TV app, Microsoft Internet Explorer or Microsoft Edge Unwanted horizontal stripes appear on the video playback window when viewing online videos on YouTube using Microsoft Internet Explorer or Microsoft Edge browser. They are also seen while watching online videos using the Movies and TV app.
  • Change the monitor resolution to 4k 3840 x 1080 or lower.
  • For YouTube videos, change the playback resolution to 720p or lower.

The following table contains information about troubleshooting USB issues on your Dell P3424WEB monitor.

Table 4: Troubleshooting USB issues on Dell P3424WEB monitor.
Troubleshooting USB Issues
Specific Symptoms What User Experiences Possible Solution
USB interface is not working. USB devices are not working.
  • Check that your monitor is turned On.
  • Reconnect the upstream cable to your computer.
  • Reconnect the USB devices (downstream connector).
  • Switch Off and then turn On the monitor again.
  • Reboot the computer.
  • Some USB devices such as an external hard drive require a higher electric current, connect the device directly to the computer.
The super speed USB 3.2 Gen1 interface is slow. Super speed USB 3.2 Gen1 peripherals working slowly or not working at all
  • Check that your computer is USB 3.0 capable.
  • Some computers have USB 3.0, USB 2.0, and USB 1.1 ports.
  • Ensure that the correct USB port is used.
  • Reconnect the upstream cable to your computer.
  • Reconnect the USB devices (downstream connector).
  • Reboot the computer.
Wireless USB devices stop working when a USB 3.0 device is plugged in. Wireless USB devices responding slowly or only working as the distance between itself and its receiver decreases.
  • Increase the distance between the USB 3.0 devices and the wireless USB receiver.
  • Position your wireless USB receiver as close as possible to the wireless USB devices.
  • Use a USB-extender cable to position the wireless USB receiver as far away as possible from the USB 3.0 port.
No charging when using USB Type-C connection to computer, laptop, and so on No charging.
  • Verify if the device can support one of the 5 V/9 V/15 V/20 V charging profiles.
  • Verify if the Notebook requires a >90 W power adapter.
  • If the Notebook requires a >90 W power adapter, it may not charge with the USB Type-C connection.
  • Ensure that you use only the Dell approved adapter or the adapter that comes with the product.
  • Ensure that the USB Type-C cable is not damaged.
Intermittent charging when using USB Type-C connection to computer, laptop, and so on Intermittent charging
  1. Check if the maximum power consumption of the device is over 90 W.
  2. Ensure that you use only the Dell approved adapter or the adapter that comes with the product.
  3. Ensure that the USB Type-C cable is not damaged.

Frequently Asked Questions

For more information, click to expand a section below.

NOTE: If you do not see the recommended resolution as an option, update the video card (GPU) driver of your Dell computer from https://www.dell.com/support/drivers or the video card (GPU) manufacturer's website. Learn How to Download and Install Dell Drivers.

Using Windows Display Settings

In Windows 11, Windows 10, Windows 8 or 8.1, and Windows 7:

  1. For Windows 8 and Windows 8.1 only, select the Desktop tile to switch to the classic desktop view.
  2. Right-click the desktop and click Screen Resolution.
  3. Click the dropdown list of the Screen Resolution and select 3440 x 1440.
  4. Click OK.

Using Nvidia Control Panel

To change the resolution using the Nvidia Control Panel:

  1. Right-click the desktop and click Nvidia Control Panel.
  2. Click the + symbol next to Display on the left pane.
  3. Select Change Resolution under Display.
  4. In the dropdown menu on the right pane, select the resolution 3440 x 1440.
  5. Click Apply.

Using AMD Catalyst Control Center

To change the resolution using the AMD Catalyst Control Center:

  1. Right-click the desktop and click AMD Catalyst Control Center.
  2. Click the + symbol next to Display on the left pane.
  3. Select Change Resolution under Display.
  4. In the dropdown menu on the right pane, select the resolution 3440 x 1440.
  5. Click Apply.

The Dell P3424WEB monitor has two built-in diagnostics that are available:

  • Self-Test Feature Check - The self-test feature check on the Dell P3424WEB monitor allows you to check whether the monitor is functioning properly.

  • Built-In Self-Test - The Dell P3424WEB monitor has a built-in self-test that helps you identify if the screen abnormality is with the monitor or the video card (GPU) on your computer. When you notice screen abnormalities such as distortion, clarity, horizontal or vertical lines, color fade. It is always a good practice to isolate the monitor by running the built-in diagnostics.

Learn how to run a diagnostic test on the Dell P3424WEB monitor.

The troubleshooting section of this article provides information about troubleshooting common issues with your Dell P3424WEB monitor.

This section has troubleshooting steps on how to resolve power issues, video issues, color or clarity issues, distortion issues, horizontal or vertical lines, brightness issues or pixel issues, and so on.

Learn how to access the on-screen display (OSD) menu on the Dell P3424WEB monitor. For additional product-specific information, see the user manual of the Dell P3424WEB monitor.

Information about the monitor such as the model number, firmware version, and Service Tag can be accessed using the on-screen display (OSD) menu of the monitor.

Learn how to access the on-screen display (OSD) menu on the Dell P3424WEB monitor. For additional product-specific information, see the user manual of the Dell P3424WEB monitor.

NOTE: The default factory setting on the Dell P3424WEB is DisplayPort 1.2 (HDCP 2.2).
  1. Press the joystick on the monitor to enter the On-Screen Display (OSD) Menu.
  2. Press up or down to highlight Input Source in the menu and press on the joystick to select.
  3. Press up or down to highlight DP in the menu.

Dell P3424WEB Joystick Control
Figure 5: Dell P3424WEB Joystick Control

NOTE: The default factory setting on the Dell P3424WEB is HDMI 2.1 (TMDS).
  1. Press the joystick on the monitor to enter the On-Screen Display (OSD) Menu.
  2. Press up or down to highlight Input Source in the menu and press on the joystick to select.
  3. Press up or down to highlight HDMI in the menu.
  4. Press and hold on the joystick for approximately 10 s until the HDMI configuration message appears.

Dell P3424WEB Joystick Control
Figure 6: Dell P3424WEB Joystick Control

The USB-C port on your Dell P3424WEB supports USB Power Delivery, Data, and DisplayPort video signal. The USB-C port can be used for video and data signals, and supply power (90 W) to a compatible laptop using a single USB-C cable that is provided with the monitor.

NOTE: Dell P3424WEB can supply power using the USB-C cable only to a compatible laptop that supports Power Delivery (PD) over USB-C. Not all laptops with USB-C support Power Delivery For more information, see the user manual or contact the laptop manufacturer.
NOTE: USB-C power delivery-compliant port (PD version 2.0) delivers up to 90 W of power. If your laptop requires more than 90 W to operate and the battery is drained. It is recommended you use the standard AC adapter of the laptop to power on and charge the laptop battery.

If you are using a Dell laptop that supports charging using USB-C, Dell Technologies recommends installing the latest BIOS and video card (GPU) driver. Learn How to Download and Install Dell Drivers.

For information about the supported orientation to set up the Dell P3424WEB monitor, see the monitor orientation section of this article.

Affected Products

Dell P3424WEB
Article Properties
Article Number: 000219777
Article Type: How To
Last Modified: 22 Nov 2023
Version:  1
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.