目标
- 概述
- 设置所需的命令
- 验证状态
概述
HiveAgent 用于通过 HiveManager 软件应用程序进行通信和允许管理指定的交换机设备。 它可以是 AeroHive 品牌 AeroHive HiveManager NG 或 Dell 品牌 OEM 版本 Goldenrod (目前称为 "极端 IQ")。
当系统在没有启动配置(不是与空启动-config 相同)的情况下引导并且主堆栈交换机上不存在 EULA 接受文件时,将出现以下提示:
AeroHive HiveManager NG EULA 此交换机包括一项功能,通过将交换机的服务标签号发送至 HiveManager 来验证您的授权使用 HiveManager,使其能够与 HiveManager (可选的 management suite)一起使用。如果您想要禁用此功能,您应在首次接通交换机电源时或在此后的任何时间运行命令 "eula-同意 hiveagent 拒绝"。
警报: 在升级当前正在运行的交换机的交换机固件时,在从 6.3.0. x 版本升级到6.3.0.15 之前必须运行的固件发行说明(位于固件下载 zip 文件中)中列出了具体步骤。解决方案知识库文章
SLN302479还可由 Dell 代表在内部引用。
ALERT: 操作系统 6.7. x 映像不再包含 HiveAgent 应用程序,以允许与极端 CloudIQ (以前的 AeroHive Hivemanager NG)或 XiQ (以前的本地 Hivemanager NG)实例建立连接。如果需要此功能,请勿将 Dell N 系列校园交换机的基本代码更新为 OS 6.7. x 映像。OS 6.6.3 映像将被视为安全的安全港版本,以保留 HiveAgent 功能和命令集。
注意: 当前,在非堆叠环境中仅支持 N-1500、N-2000 和 N 3000。
设置所需的命令
命令 |
参数 |
DellSwitch# configure |
进入全局配置模式。 |
DellSwitch (config) # eula-同意 hiveagent 拒绝 |
使用此命令可关闭 Hiveagent。 默认模式为打开。 |
DellSwitch (config) # eula-同意 hiveagent accept |
打开 HiveAgent (如果之前手动关闭)。 |
DellSwitch (config) # hiveagent |
进入HiveAgent配置模式。 |
DellSwitch (会议-hiveagent) #server HiveManagerNG |
输入服务器子集命令并命名服务器。 默认名称为 HiveManagerNG |
DellSwitch (会议-hiveagent-HiveManagerNG) #enable |
默认情况下,默认设置(HiveManagerNG)服务器处于启用状态。 使用 "no enable" 禁用 |
验证状态
HiveAgent 接受的示例:
DellSwitch # show eula-同意 hiveagent
HiveAgent EULA:
已接受有关 HiveAgent EULA 的附加信息,如下所示:
此交换机包括一项功能,使其能够与 HiveManager
(可选的 management suite)一起工作,方法是将交换机的服务
标签号和 IP 地址发送到 HiveManager,以验证您的授权使用 HiveManager。
如果您想要禁用此功能,您应在
首次接通交换机电源时或在此后的任何时间运行命令 "eula-同意 hiveagent 拒绝"。
DellSwitch # show hiveagent status
HiveAgent:已启用
EULA:接受的
HiveManager 服务器名称:HiveManagerNG
HIVEMANAGER NG (已启用): cloud-rd.aerohive.com
HiveAgent 拒绝的示例:
DellSwitch # show eula-同意 hiveagent
HiveAgent EULA:拒绝
了有关 HiveAgent EULA 的附加信息,如下所示:
我不接受许可协议中的条款。HiveAgent 功能已
停用并且无法再使用。
要启用 HiveAgent 配置,请
通过配置《 eula-同意 HiveAgent 接受 ' 来接受许可协议条款。
DellSwitch # show hiveagent status
HiveAgent:已禁用
EULA:不接受
HiveManager 服务器名称:HiveManagerNGHiveManager NG(已启用):