Skip to main content
Sign Out

Welcome to Dell

My Account
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Enjoy members-only rewards and discounts
  • Create and access a list of your products
Sign In Create an Account Dell Financial Services Premier Sign In Partner Program Sign In
Contact Us

Your Dell.com Carts

Some article numbers may have changed. If this isn't what you're looking for, try searching all articles. Search articles

How to Configure and Manage Pause Frames using Flow Control on Dell Networking Force10 switches

Summary: How to configure and Manage Pause Frames on Dell switch, configure flow control on Dell switch, set up flow control on Dell Force10 switch

This article applies to This article does not apply to This article is not tied to any specific product. Not all product versions are identified in this article.
Check out other resources

Instructions

This article explains how to configure and manage pause frames using Flow Control on Dell Networking Force10 switches

 

Objectives

 
1.  Definition of pause frames
2.  How to enable Flow Control 
3.  How to view interface statistics for pause frames

 

Definition of Pause Frames

 

Ethernet Pause Frames allow for a temporary stop in data transmission. A situation may arise where a sending device may transmit data faster than a destination device can accept it. The destination sends a PAUSE frame back to the source, stopping the sender's transmission for a period of time .

The PAUSE frame is defined by IEEE 802.3x and uses MAC Control frames to carry the PAUSE commands. Ethernet pause frames are supported on full duplex only.
 
If a port is over-subscribed, Ethernet Pause Frame flow control does not ensure no-loss behavior.

 

Ethernet Pause Frame flow control is not supported if Priority Flow Control (PFC) is enabled on an interface.

 

How to enable Flow Control


Control how the system responds to and generates 802.3x pause frames on Ethernet interfaces. The default is rx off tx off.

To enable pause frames, use the following command on 1 and 10 gig interface ports.

 
flowcontrol rx [off | on] tx [off | on] [negotiate]


 
  • rx on -  to process the received flow control frames on this port.
  • rx off -  to ignore the received flow control frames on this port.
  • tx on -  to send control frames from this port to the connected device when a higher rate of traffic is received.
  • tx off -  flow control frames are not sent from this port to the connected device when higher rate of traffic is received.


How to view interface statistics for pause frames
 


You can view the current count of throttles since the last time the counters were cleared with this command:throttles.    as pause framesDell Networking Force10 switches report

 

Dell#show interface te 0/1
TenGigabitEthernet 0/1 is down, line protocol is down
Hardware is DellEth, address is 00:01:e8:8b:18:bb
    Current address is 00:01:e8:8b:18:bb
Pluggable media not present
Interface index is 1048708
Internet address is not set
Mode of IPv4 Address Assignment : NONE
DHCP Client-ID :0001e88b18bb
MTU 1554 bytes, IP MTU 1500 bytes
LineSpeed auto
Flowcontrol rx off tx off
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters 16:48:20
Queueing strategy: fifo
Input Statistics:
     0 packets, 0 bytes
     0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
     0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
     0 Multicasts, 0 Broadcasts, 0 Unicasts
     0 runts, 0 giants, 0 throttles
     0 CRC, 0 overrun, 0 discarded
Output Statistics:
     0 packets, 0 bytes, 0 underruns
     0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
     0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
     0 Multicasts, 0 Broadcasts, 0 Unicasts
     0 throttles, 0 discarded, 0 collisions, 0 wreddrops
Rate info (interval 299 seconds):
     Input 00.00 Mbits/sec,          0 packets/sec, 0.00% of line-rate
     Output 00.00 Mbits/sec,          0 packets/sec, 0.00% of line-rate
Time since last interface status change: 16:46:37

 



 

Affected Products

Force10 MXL Blade, Force10 S25N-S50N, Force10 S25-01-GE-24P, Force10 S25-01-GE-24T, Force10 S25-01-GE-24V, Force10 S50-01-GE-48T-V, Force10 S50-01-GE-48T, PowerSwitch S4810P, PowerSwitch S5000, Force10 S50P, Force10 S55T, Force10 S60-44T , PowerSwitch S6000, Force10 Z9000 ...
Article Properties
Article Number: 000120576
Article Type: How To
Last Modified: 21 Feb 2021
Version:  3
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.