ECS xDoctor：一或多個網路介面故障或遺失

Table of Contents

Detailed Article

Symptoms

Cause

Resolution

Additional Info

Affected Products

Provide Feedback

Summary: xDoctor 回報警告錯誤，指出其中一個 ECS 介面已關閉至交換器。

This article applies to This article does not apply to

Check out resources for

Symptoms

xDoctor 報告以下警告，指出其中一個 ECS 介面已關閉：

Displaying xDoctor Report (2017-09-01_064438) Filter:['CRITICAL', 'ERROR', 'WARNING'] ...

Timestamp    = 2017-09-01_064438
    Category = platform
    Source   = ip show
    Severity = WARNING
    Node     = 169.254.1.1
    Message  = One or more network interfaces are down or missing
    Extra    = {'1xx.2xx.1.4': ['slave-0']}

檢查叢集上的介面連結狀態。在下面的示例中，節點 4 具有 NO-CARRIER，這意味著沒有連接到 secondary-0 介面。

命令：

# viprexec -i 'ip link show | egrep "slave-|public"'

範例：

admin@node1:~> viprexec -i 'ip link show | egrep "slave-|public"'

Output from host : 1xx.1xx.219.1
bash: public: command not found
3: slave-0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master public state UP mode DEFAULT group default qlen 1000
5: slave-1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master public state UP mode DEFAULT group default qlen 1000
10: public: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default

Output from host : 1xx.1xx.219.2
bash: public: command not found
3: slave-0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master public state UP mode DEFAULT group default qlen 1000
5: slave-1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master public state UP mode DEFAULT group default qlen 1000
10: public: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default

Output from host : 1xx.1xx8.219.3
bash: public: command not found
4: slave-0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master public state UP mode DEFAULT group default qlen 1000
5: slave-1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master public state UP mode DEFAULT group default qlen 1000
10: public: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default

Output from host : 1xx.1xx.219.4
bash: public: command not found
2: slave-0: <NO-CARRIER,BROADCAST,MULTICAST,SLAVE,UP> mtu 1500 qdisc mq master public state DOWN mode DEFAULT group default qlen 1000
5: slave-1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc mq master public state UP mode DEFAULT group default qlen 1000
10: public: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default

確認個別介面偵測到連結：

命令：

# viprexec -i "echo slave-0;sudo ethtool slave-0 | grep 'Link detected:';echo slave-1;sudo ethtool slave-1 | grep 'Link detected:'"

範例：

admin@node1:~> viprexec -i "echo slave-0;sudo ethtool slave-0 | grep 'Link detected:';echo slave-1;sudo ethtool slave-1 | grep 'Link detected:'"

Output from host : 1xx.1xx.219.1
slave-0
        Link detected: yes
slave-1
        Link detected: yes

Output from host : 1xx.1xx.219.2
slave-0
        Link detected: yes
slave-1
        Link detected: yes

Output from host : 1xx.1xx.219.3
slave-0
        Link detected: yes
slave-1
        Link detected: yes

Output from host : 1xx.1xx.219.4
slave-0
        Link detected: no
slave-1
        Link detected: yes

確認交換器在第 1 代或第 2 代環境中為 Arista，以及在第 3 代環境中為 Dell （或其他型號）。

注意：如果交換器不是 Arista 或 Dell 交換器，則它們是使用者管理的交換器。我們必須通知使用者他們有連線中斷以進行補救。

命令：

# viprexec -i "sudo lldpcli show neigh | grep SysDescr"

範例：
Gen 1 或 Gen 2

admin@ecssh121:~> viprexec -i "sudo lldpcli show neigh | grep SysDescr"

Output from host : 1xx.1xx.219.1
    SysDescr:     Arista Networks EOS version 4.11.7.2 running on an Arista Networks DCS-7150S-24
    SysDescr:     Arista Networks EOS version 4.11.7.2 running on an Arista Networks DCS-7150S-24
    SysDescr:     Arista Networks EOS version 4.15.6M running on an Arista Networks DCS-7048T-A

Output from host : 1xx.1xx.219.2
    SysDescr:     Arista Networks EOS version 4.11.7.2 running on an Arista Networks DCS-7150S-24
    SysDescr:     Arista Networks EOS version 4.11.7.2 running on an Arista Networks DCS-7150S-24
    SysDescr:     Arista Networks EOS version 4.15.6M running on an Arista Networks DCS-7048T-A

Output from host : 1xx.1xx.219.3
    SysDescr:     Arista Networks EOS version 4.11.7.2 running on an Arista Networks DCS-7150S-24
    SysDescr:     Arista Networks EOS version 4.11.7.2 running on an Arista Networks DCS-7150S-24
    SysDescr:     Arista Networks EOS version 4.15.6M running on an Arista Networks DCS-7048T-A

Output from host : 1xx.1xx.219.4
    SysDescr:     Arista Networks EOS version 4.11.7.2 running on an Arista Networks DCS-7150S-24
    SysDescr:     Arista Networks EOS version 4.11.7.2 running on an Arista Networks DCS-7150S-24
    SysDescr:     Arista Networks EOS version 4.15.6M running on an Arista Networks DCS-7048T-A

範例：
Gen 3

admin@ecsnode1:~> viprexec -i "sudo lldpcli show neigh | grep SysDescr"

Output from host : 1xx.1xx.219.1
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10

Output from host : 1xx.1xx.219.2
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10

Output from host : 1xx.1xx.219.3
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10

Output from host : 1xx.1xx.219.4
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10

Output from host : 1xx.1xx.219.5
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10

Output from host : 1xx.1xx.219.6
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10

Output from host : 1xx.1xx.219.7
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10

Output from host : 11xx.1xx.219.8
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10
    SysDescr:     OS10

檢查節點上公用介面組態的 secondary-0 和 secondary -1 的公用繫結，顯示步驟 2 中的命令未偵測到任何連結：

命令：

# sudo cat /etc/sysconfig/network/ifcfg-public

範例：

admin@node4:~> sudo cat /etc/sysconfig/network/ifcfg-public
BONDING_MASTER=yes
BONDING_MODULE_OPTS="miimon=100 mode=4 xmit_hash_policy=layer3+4"
BONDING_SLAVE0=slave-0
BONDING_SLAVE1=slave-1
BOOTPROTO=static
IPADDR=xxx.xxx.xxx.xxx/xx
MTU=1500
STARTMODE=auto

確認已在節點上設定正確的連結聚合控制通訊協定（LACP）參數。（IEEE 802.3ad 動態連結聚合是預設設定，也是預期設定。）

命令：

# viprexec -i "grep Mode /proc/net/bonding/public"

範例：

admin@node1:~> viprexec -i "grep Mode /proc/net/bonding/public"

Output from host : 1xx.1xx.219.1
Bonding Mode: IEEE 802.3ad Dynamic link aggregation

Output from host : 1xx.1xx.219.2
Bonding Mode: IEEE 802.3ad Dynamic link aggregation

Output from host : 1xx.1xx.219.3
Bonding Mode: IEEE 802.3ad Dynamic link aggregation

Output from host : 1xx.1xx.219.4
Bonding Mode: IEEE 802.3ad Dynamic link aggregation

執行下列步驟，確認連接埠的連線一致，且介面已連接：

ECS Gen 1 或 Gen 2：

節點的第一代或第二代 ECS 對應如下，對應至對應的交換器連接埠：

乙太網 9 = 節點 1
乙太網 10 = 節點 2
乙太網 11 = 節點 3
乙太網 12 = 節點 4
乙太網 13 = 節點 5
乙太網 14 = 節點 6
乙太網 15 = 節點 7
乙太網 16 = 節點 8

命令：

# viprexec -i "sudo lldpcli show neigh | egrep 'SysName|PortID'"

範例：

（第一代或第二代 ECS 的範例）

admin@ecssh121:~> viprexec -i "sudo lldpcli show neigh | egrep 'SysName|PortID'"                                                                                                                                                     
Output from host : 1xx.1xx.219.1
    SysName:      rabbit
    PortID:       ifname Ethernet9
    SysName:      hare
    PortID:       ifname Ethernet9
    SysName:      turtle
    PortID:       ifname Ethernet1

Output from host : 1xx.1xx.219.2
    SysName:      rabbit
    PortID:       ifname Ethernet10
    SysName:      hare
    PortID:       ifname Ethernet10
    SysName:      turtle
    PortID:       ifname Ethernet2

Output from host : 1xx.1xx.219.3
    SysName:      hare
    PortID:       ifname Ethernet11
    SysName:      rabbit
    PortID:       ifname Ethernet11
    SysName:      turtle
    PortID:       ifname Ethernet3

Output from host : 1xx.1xx.219.4
    SysName:      hare
    PortID:       ifname Ethernet12
    SysName:      turtle
    PortID:       ifname Ethernet4

注意：在上述範例中，節點 4 遺失與 Ethernet12 rabbit 的連線。透過目前收集的所有資訊，我們現在知道連接埠 12 位於 rabbit 交換器上連接到節點 4 的 secondary-0 介面

ECS Gen 3：
節點的第三代 ECS 對應如下，對應至對應的交換器連接埠：

乙太網 1/1/1 = 節點 1 乙太網 1/1/2 = 節點 2
乙太網 1/1/3 = 節點 3
乙太網 1/1/4 = 節點 4
乙太網 1/1/5 = 節點 5
乙太網 1/1/6 = 節點 6
乙太網 1/1/7 = 節點 7
乙太網 1/1
/8 = 節點 8

確認連線至四個 ECS Gen 3 交換器前端兔和野兔後端狐狸和獵犬的 ECS 連線已開啟。

命令：

# viprexec -i "sudo lldpcli show neigh | egrep 'SysName|PortID'"

範例：

admin@ecsnode1:~> viprexec -i "sudo lldpcli show neigh | egrep 'SysName|PortID'"

Output from host : 1xx.1xx.219.1
    SysName:      rabbit
    PortID:       ifname ethernet1/1/1
    SysName:      hare
    PortID:       ifname ethernet1/1/1
    SysName:      fox
    PortID:       ifname ethernet1/1/1
    SysName:      hound
    PortID:       ifname ethernet1/1/1

Output from host : 192.168.219.2
    SysName:      rabbit
    PortID:       ifname ethernet1/1/2
    SysName:      hare
    PortID:       ifname ethernet1/1/2
    SysName:      fox
    PortID:       ifname ethernet1/1/2
    SysName:      hound
    PortID:       ifname ethernet1/1/2

Output from host : 1xx.1xx.219.3
    SysName:      rabbit
    PortID:       ifname ethernet1/1/3
    SysName:      hare
    PortID:       ifname ethernet1/1/3
    SysName:      fox
    PortID:       ifname ethernet1/1/3
    SysName:      hound
    PortID:       ifname ethernet1/1/3

Output from host : 1xx.1xx.219.4
    SysName:      rabbit
    PortID:       ifname ethernet1/1/4
    SysName:      hare
    PortID:       ifname ethernet1/1/4
    SysName:      fox
    PortID:       ifname ethernet1/1/4
    SysName:      hound
    PortID:       ifname ethernet1/1/4

Output from host : 1xx.1xx.219.5
    SysName:      rabbit
    PortID:       ifname ethernet1/1/5
    SysName:      hare
    PortID:       ifname ethernet1/1/5
    SysName:      fox
    PortID:       ifname ethernet1/1/5
    SysName:      hound
    PortID:       ifname ethernet1/1/5

Output from host : 1xx.1xx.219.6
    SysName:      rabbit
    PortID:       ifname ethernet1/1/6
    SysName:      hare
    PortID:       ifname ethernet1/1/6
    SysName:      fox
    PortID:       ifname ethernet1/1/6
    SysName:      hound
    PortID:       ifname ethernet1/1/6

Output from host : 1xx.1xx.219.7
    SysName:      rabbit
    PortID:       ifname ethernet1/1/7
    SysName:      hare
    PortID:       ifname ethernet1/1/7
    SysName:      fox
    PortID:       ifname ethernet1/1/7
    SysName:      hound
    PortID:       ifname ethernet1/1/7

Output from host : 1xx.1xx.219.8
    SysName:      rabbit
    PortID:       ifname ethernet1/1/8
    SysName:      hare
    PortID:       ifname ethernet1/1/8
    SysName:      fox
    PortID:       ifname ethernet1/1/8
    SysName:      hound
    PortID:       ifname ethernet1/1/8

使用管理員登入資料連線至 rabbit，並檢查介面狀態。

命令：
ECS Gen 1 或 Gen 2

# ssh <switch name>
# show interfaces show interfaces Ethernet<Interface Number>

範例：

ECS Gen 1 或 Gen 2

admin@ecs1:~> ssh rabbit
Password:
Last login: Tue Sep  5 11:13:30 2017 from 1xx.1xx.219.1
rabbit>show interfaces Ethernet12
Ethernet12 is down, line protocol is notpresent (notconnect)
  Hardware is Ethernet, address is 444c.a8de.8f83 (bia 444c.a8de.8f83)
  Description: MLAG group 4
  Member of Port-Channel4
  Ethernet MTU 9214 bytes , BW 10000000 kbit
  Full-duplex, 10Gb/s, auto negotiation: off, uni-link: n/a
  Loopback Mode : None
  0 link status changes since last clear
  Last clearing of "show interface" counters never
  5 minutes input rate 0 bps (0.0% with framing overhead), 0 packets/sec
  5 minutes output rate 0 bps (0.0% with framing overhead), 0 packets/sec
     0 packets input, 0 bytes
     Received 0 broadcasts, 0 multicast
     0 runts, 0 giants
     0 input errors, 0 CRC, 0 alignment, 0 symbol, 0 input discards
     0 PAUSE input
     0 packets output, 0 bytes
     Sent 0 broadcasts, 0 multicast
     0 output errors, 0 collisions
     0 late collision, 0 deferred, 0 output discards
     0 PAUSE output

命令：
ECS Gen 3

# ssh <switch name>
# show interfaces ethernet 1/1/<Interface Number>

範例：
ECS Gen 3

rabbit# show interface ethernet 1/1/4
Ethernet 1/1/9 is up, line protocol is down
Description: VLT Group 9
Port is part of Port-channel 9
Hardware is Dell EMC Eth, address is d8:9e:f3:c6:31:09
    Current address is d8:9e:f3:c6:31:09
Pluggable media not present

Interface index is 17305276
Internet address is not set
Mode of IPv4 Address Assignment: not set
Interface IPv6 oper status: Enabled
MTU 9216 bytes, IP MTU 9184 bytes
LineSpeed 0, Auto-Negotiation off
FEC is auto
Flowcontrol rx off tx off
ARP type: ARPA, ARP Timeout: 60
Last clearing of "show interface" counters: 6 days 17:39:09
Queuing strategy: fifo
Input statistics:
     0 packets, 0 octets
     0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
     0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
     0 Multicasts, 0 Broadcasts, 0 Unicasts
     0 runts, 0 giants, 0 throttles
     0 CRC,  overrun, 0 discarded
Output statistics:
     0 packets, 0 octets
     0 64-byte pkts, 0 over 64-byte pkts, 0 over 127-byte pkts
     0 over 255-byte pkts, 0 over 511-byte pkts, 0 over 1023-byte pkts
     0 Multicasts, 0 Broadcasts, 0 Unicasts
     0 throttles, 0 discarded, 0 Collisions, 0 wreddrops
Rate Info(interval 299 seconds):
     Input 0 Mbits/sec, 0 packets/sec, 0% of line rate
     Output 0 Mbits/sec, 0 packets/sec, 0% of line rate
Time since last interface status change: 6 days 17:39:10

檢查可能的網路介面卡問題：
另一個元件，用以檢查受影響節點上最近的 NIC 節點上的節點訊息緩衝區（dmesg）是否有最近的 NIC 問題。在以下範例中，NIC 會在處於開啟和關閉狀態之間迴圈。

如果 dmesg 中有 NIC 警示，則可能需要更換。

如果 ECS Gen 1 或 Gen 2 - 提供輸出給 ECS 支援硬體工程師進行分析。
如果是 ECS Gen 3 - 將輸出提供給會成為 EX 系列硬體專家的 Dell 硬體團隊。

命令：

# sudo dmesg -T

範例：

admin@node1:~> sudo dmesg -T
[Tue Jul  6 09:40:56 2021] public: link status definitely up for interface slave-1, 25000 Mbps full duplex
[Tue Jul  6 09:40:56 2021] bnxt_en 0000:04:00.1 slave-1: NIC Link is Down
[Tue Jul  6 09:40:56 2021] public: link status definitely down for interface slave-1, disabling it
[Tue Jul  6 09:40:57 2021] public: link status definitely down for interface slave-1, disabling it
[Tue Jul  6 09:41:09 2021] bnxt_en 0000:04:00.1 slave-1: NIC Link is Up, 25000 Mbps full duplex, Flow control: ON - receive & transmit
[Tue Jul  6 09:41:09 2021] bnxt_en 0000:04:00.1 slave-1: FEC autoneg off encodings: None
[Tue Jul  6 09:41:09 2021] public: link status definitely up for interface slave-1, 25000 Mbps full duplex
[Tue Jul  6 09:41:10 2021] bnxt_en 0000:04:00.1 slave-1: NIC Link is Down
[Tue Jul  6 09:41:10 2021] bnxt_en 0000:04:00.1 slave-1: speed changed to 0 for port slave-1
[Tue Jul  6 09:41:11 2021] public: link status definitely down for interface slave-1, disabling it
[Tue Jul  6 09:41:20 2021] bnxt_en 0000:04:00.1 slave-1: NIC Link is Up, 25000 Mbps full duplex, Flow control: ON - receive & transmit
[Tue Jul  6 09:41:20 2021] bnxt_en 0000:04:00.1 slave-1: FEC autoneg off encodings: None
[Tue Jul  6 09:41:20 2021] public: link status definitely up for interface slave-1, 25000 Mbps full duplex
[Tue Jul  6 09:41:22 2021] bnxt_en 0000:04:00.1 slave-1: NIC Link is Down
[Tue Jul  6 09:41:22 2021] bnxt_en 0000:04:00.1 slave-1: speed changed to 0 for port slave-1
[Tue Jul  6 09:41:22 2021] public: link status definitely down for interface slave-1, disabling it
[Tue Jul  6 09:41:31 2021] bnxt_en 0000:04:00.1 slave-1: NIC Link is Up, 25000 Mbps full duplex, Flow control: ON - receive & transmit
[Tue Jul  6 09:41:31 2021] bnxt_en 0000:04:00.1 slave-1: FEC autoneg off encodings: None
[Tue Jul  6 09:41:32 2021] public: link status definitely up for interface slave-1, 25000 Mbps full duplex
[Tue Jul  6 09:41:33 2021] bnxt_en 0000:04:00.1 slave-1: NIC Link is Down

Cause

此問題的可能原因：

有時，小型可插拔（SFP）在安裝階段未正確安裝。
使用者管理的交換器，是在控制之外進行變更（在維護使用者管理的交換器的情況下，例如韌體升級，連結可能會中斷，並可能重新協商，如下方解決方案部分所示。）
彈性雲端伺服器硬體故障：
- 網路介面卡
- 網路纜線
- 小型可插拔（SFP）
- 網路交換器或交換器連接埠

Resolution

做任何工作
之前在使用者管理的交換器得到維護的情況下（例如韌體升級），連結可能會中斷，並可能重新協商。以下範例適用於使用者在使用者管理的 FE 交換器上完成韌體升級後的 secondary-0 關閉。以下命令用於重新協商介面：

ethtool -r <i/f name>

admin@ecs-n-1:~> sudo ethtool slave-0
Settings for slave-0:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full 
                                10000baseSR/Full 
        Supported pause frame use: Symmetric
        Supports auto-negotiation: Yes
        Advertised link modes:  1000baseX/Full 
                                10000baseSR/Full 
        Advertised pause frame use: No
        Advertised auto-negotiation: Yes
        Speed: Unknown!
        Duplex: Unknown! (255)
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: off
        Supports Wake-on: g
        Wake-on: g
        Current message level: 0x0000000f (15)
                               drv probe link timer
        Link detected: no                   
admin@ecs-n-1:~>

admin@ecs-n-1:~> sudo ethtool -r slave-0
admin@ecs-n-1:~> 

admin@ecs-n-1:~> sudo ethtool slave-0
Settings for slave-0:
        Supported ports: [ FIBRE ]
        Supported link modes:   1000baseX/Full 
                                10000baseSR/Full 
        Supported pause frame use: Symmetric
        Supports auto-negotiation: Yes
        Advertised link modes:  1000baseX/Full 
                                10000baseSR/Full 
        Advertised pause frame use: No
        Advertised auto-negotiation: Yes
        Speed: 10000Mb/s
        Duplex: Full
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: off
        Supports Wake-on: g
        Wake-on: g
        Current message level: 0x0000000f (15)
                               drv probe link timer
        Link detected: yes

注意：如果介面仍然故障且無法重新協商，則必須有 Dell 代表到場檢查並重新安裝 SPF 和纜線。如果這樣做無法解決，建議更換從交換器至節點的 SFP 和纜線連線。

有不同的 SFP 機型使用銅線或光纖。此外，後端和前端交換器可能使用不同類型的 SFP 電線。在更換零件之前，請先確認需要哪一個零件。

Additional Information

從 ECS 硬體指南 Gen1 或 Gen2 擷取：

網路佈線
網路佈線圖適用於 Dell 或客戶提供機架中的 U 系列、D 系列或 C 系列 ECS 應用裝置。

為了區分這三個交換器，每個交換器都有一個暱稱：

野兔：10 GbE 公用交換器位於 U 系列或 D 系列的機架頂端，或是 C 系列段的頂端交換器。
兔子：10 GbE 公用交換器位於 U 系列或 D 系列機架頂端的 Hare 下方，或 C 系列網段中 Hare 交換器的下方。
海龜：1 GbE 專用交換器，位於 U 系列機架頂端的 rabbit 下方，或是 C 系列網段的 hare 交換器下方。

U 系列和 D 系列網路佈線
下圖顯示由 Dell 或客戶設定之 U 系列或 D 系列 ECS 之八節點機架組態的簡化網路佈線圖。在此圖之後，其他詳細圖和表格提供了埠、標籤和電纜顏色資訊。

請參閱下表以瞭解交換器和連接埠的配對資訊，以及適當的交換器連接埠號碼

。交換器 1 = Rabbit = 底部交換器交換器 2 = Hare = 頂部交換器

節點連接埠：
次要-0 = P01 = 右連接埠 - 連接到交換器 1/Rabbit/底部交換器。
次要 1 = P02 = 左側連接埠 - 連接到交換器 2/Hare/Top 交換器。

Affected Products

ECS Appliance

Products

ECS Appliance, ECS Appliance Gen 1, ECS Appliance Gen 2, ECS Appliance Gen 3, ECS Appliance Hardware Gen1 U-Series, Elastic Cloud Storage

ECS xDoctor：一或多個網路介面故障或遺失

Summary: xDoctor 回報警告錯誤，指出其中一個 ECS 介面已關閉至交換器。

Symptoms

Cause

Resolution

Additional Information

Affected Products

Products

Article Properties

Find answers to your questions from other Dell users

Support Services

Article Properties

Find answers to your questions from other Dell users

Support Services

Welcome

Welcome to Dell

ECS xDoctor：一或多個網路介面故障或遺失

Summary: xDoctor 回報警告錯誤，指出其中一個 ECS 介面已關閉至交換器。

Detailed Article

Symptoms

Cause

Resolution

Additional Info

Affected Products

Symptoms

Cause

Resolution

Additional Information

Affected Products

Products

Article Properties

Find answers to your questions from other Dell users

Support Services

Article Properties

Find answers to your questions from other Dell users

Support Services