Skip to main content
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Enjoy members-only rewards and discounts
  • Create and access a list of your products

Latitude 5410 Teardown, Removal guide for customer replaceable units (CRUs)

Summary: A guide to those parts of the Dell Latitude 5410 Notebook that Dell considers it OK for anyone to remove and replace.

This article applies to This article does not apply to This article is not tied to any specific product. Not all product versions are identified in this article.

Symptoms


These guides will take you step by step through the safe removal of what are considered to be the Customer Replaceable Unit (CRU) parts of a Latitude 5410 Notebook system. (CRUs are the parts of the system that shouldn't need an engineer to remove or replace.) The guides will also include pictures to reference what's involved.


Table of Contents:

  1. CRU Removal Guide
  2. Removal Instructions

Cause

 

Removal Guide

 

If these guides do not cover what you are looking to do, then you will want to reference your System Manual.

The article below provides information on safe practises to take into consideration before working with electrical equipment.


Back to Top


Resolution

 

Removal Instructions

 

SLN321229_en_US__1icon Note: Please click on the title of the section you want to open below, in order to see the contents.
 

 

SLN321229_en_US__2ReqTools_E7450_BKeith_01

1 Small Phillip's head screwdriver 2 Plastic Scribe
3 Small Flat head screwdriver    
 
SLN321229_en_US__1icon Note: Be aware that using a large Phillips or Flat Head screwdriver may result in damage to the head of the screws. This would make their removal impossible without speciality tools, that aren't available to our onsite engineers.

 

  1. Pre-Removal Instructions before removing the Access Panel:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

  2. Turn the system over on it's closed lid and loosen the eight (8) captive screws securing the access panel to the chassis

SLN321229_en_US__4CRU_5410_Door_01_BK

  1. Using a plastic scribe or some other tool that won't mark the plastics, pry the cover up from the left-hand side hinge [1] and work clockwise around the access panel to release it from the chassis

SLN321229_en_US__5CRU_5410_Door_02_BK

  1. Lift the panel up and away from the chassis

SLN321229_en_US__6CRU_5410_Door_03_BK

 

  1. Pre-Removal Instructions before removing the Battery:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Access Panel

  2. With the system turned over on its lid, the battery is located in the bottom right-hand side of the system. Disconnect the battery cable from the motherboard

SLN321229_en_US__7CRU_5410_Battery_01_BK

  1. Loosen the single (1) captive screw on the right-hand side of the battery [1]

SLN321229_en_US__8CRU_5410_Battery_02_BK

  1. Lift the battery up an away from the system [2]

SLN321229_en_US__9icon Caution:
  • Exercise caution when handling Lithium-ion batteries
  • Discharge the battery as much as possible before removing it from the system. This can be done by disconnecting the AC adapter from the system to allow the battery to drain
  • Do not damage, or penetrate the battery with foreign objects
  • Do not expose the battery to high temperatures, or disassemble battery packs and cells
  • Do not bend the battery
  • Do not use tools of any kind to pry on or against the battery
  • Always purchase genuine batteries from Dell or authorized Dell partners and resellers

 

  1. Pre-Removal Instructions before removing the Memory:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Access Panel and Battery

  2. With the system placed on its closed lid, the memory is located in the middle of the system. Pull apart the metal clips holding the DIMM in place [1]

SLN321229_en_US__10CRU_5410_Memory_BK

  1. When the DIMM lifts up at an angle to the base, pull it out of the socket and away from the system [2]

SLN321229_en_US__1icon Note: Please repeat the steps 2 and 3 for any additional memory DIMM's located in the system.

 

  1. Pre-Removal Instructions before removing the Solid State Drive (SSD):

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Access Panel and Battery

  2. With the system on its closed lid, the SSD is located in the bottom right-hand side corner of the system. Remove the two (2) screws that secure it to the chassis [1]

SLN321229_en_US__12CRU_5410_SSD_01_BK

  1. Manouver the SSD support bracket away from the SSD connector [2]

  2. Take the SSD card off of the thermal plate

SLN321229_en_US__13CRU_5410_SSD_02_BK

  1. Remove the single (1) screw that secures the SSD bracket to the chassis [1]

SLN321229_en_US__14CRU_5410_SSD_03_BK

  1. Lift the bracket out of the slot in the chassis [2]

 

  1. Pre-Removal Instructions before removing the Heatsink and Fan:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Access Panel and Battery

  2. With the system on its closed lid, the fan is located in the top right-hand side corner of the system. Disconnect the fan cable from the motherboard

SLN321229_en_US__15CRU_5410_Fan_01_BK

  1. Remove the six (6) screws that secure the heatsink to the motherboard [1]

SLN321229_en_US__1icon Note: The screwholes on the heatsink are numbered 1 thruough 6. Remove the screws in the order they are marked on the heatsink.
 

SLN321229_en_US__17CRU_5410_Fan_02_BK

  1. Remove the two (2) screws that secure the fan to the motherboard and lift the assembly up and away from the chassis [2]

 

  1. Pre-Removal Instructions before removing the Coin Cell Battery:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Access Panel and Battery

  2. With the system on its closed lid, the coin cell battery is located at the top left-hand side corner of the system. Disconnect the coin cell battery cable from the motherboard [1]

SLN321229_en_US__18CRU_5410_CoinCell_BK

  1. lift the coin cell battery away from the adhesive on the motherboard

 

  1. Pre-Removal Instructions before removing the MicroSD Memory Card:

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

  2. The Micro SD slot is located on the right-hand edge of the system. Push in gently on the card in the slot and release to have it pop out of the slot [1]

SLN321229_en_US__19CRU_5410_MSD_BK

  1. Grip the card and pull it the rest of the way out of the slot [2]

 

  1. Pre-Removal Instructions before removing the SIM Card :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Battery

  2. The Micro SIM slot is located on the right-hand edge of the system. Push a SIM card tool or a straightened paper clip gently into the hole on the left-hand side of the SIM card slot filler until it pops out of the slot

SLN321229_en_US__20CRU_5410_MicroSIM_BK

  1. Remove the filler and fit the Micro SIM card and push the filler back into the system until it locks in place

 

  1. Pre-Removal Instructions before removing the WWAN CARD (Cellular):

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Access Panel and Battery

  2.  Remove the single (1) screw that secures the WWAN card bracket to the chassis

  3. Remove the bracket from on top of the antenna cables and the card will pop up at an angle from the motherboard

  4. Disconnect the antenna cables pop connectors from the press studs on the WWAN card

  5. Pull the card out of the connector on the motherboard and away from the system

 

  1. Pre-Removal Instructions before removing the WLAN Card (WiFi, Wireless) :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Access Panel and Battery

  2. With the system on it's closed lid, the WLAN card is located between the SSD and Coin Cell Battery on the left-hand of the system. Remove the single (1) screw that secures the WLAN card bracket to the chassis [1]

  3. Remove the bracket from on top of the antenna cables [2] and the card will pop up at an angle from the motherboard

SLN321229_en_US__21CRU_5410_WLAN_BK

  1. Disconnect the antenna cables pop connectors from the press studs on the WLAN card [3]

  2. Pull the card out of the connector on the motherboard and away from the system [4]


 

If you require further assistance, please contact Technical Support

 

  Contact Us  

Affected Products

Latitude 5410
Article Properties
Article Number: 000133667
Article Type: Solution
Last Modified: 28 Sept 2023
Version:  5
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.