Skip to main content
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Create and access a list of your products

S50N/Vを工場出荷時のデフォルト設定に設定する手順

This article applies to This article does not apply to This article is not tied to any specific product. Not all product versions are identified in this article.

Instructions

S50を工場出荷時のデフォルトにリセットするには、次の手順を実行してください。
  1. コンソールからS50N/Vデバイスに接続します
    • ボー レート = 9600
    • 文字サイズ = 8
    • フロー制御 = 無効
    • ストップ ビット = 1
    • パリティ = なし
  2. 電源コードを外して再接続するか、特権execモードで「reload」と入力して[はい]をクリックして、S50の電源を入れ直します
    • FTOS#reload
  3. BOOT_USERモードにするには、S50起動プロセス中にプロンプトが表示されたら任意のキーを押します
U-Boot 1.1.4 (F10 Development) (Oct  6 2009 - 03:14:26)
Built by build at hydrogen on Tue Oct  6  3:14:25 2009
S-Series Boot selector Label 2.8.2.0

CPU:   8541, Version: 1.1, (0x807a0011)
Core:  E500, Version: 2.0, (0x80200020)
Clock Configuration:
       CPU: 660 MHz, CCB: 330 MHz,
       DDR: 165 MHz, LBC:  41 MHz
L1:    D-cache 32 kB enabled
       I-cache 32 kB enabled
Board: S50 Force10 Networks
       Watchdog enabled
DRAM:  Initializing
    DDR: 256 MB
Top of RAM usable for U-Boot at: 10000000
Reserving 122k for U-Boot at: 0ffe0000
Reserving 136k for malloc() at: 0ffbe000
Reserving 76 Bytes for Board Info at: 0ffbdfb4
Reserving 72 Bytes for Global Data at: 0ffbdf6c
Stack Pointer at: 0ffbdf48
New Stack Pointer is: 0ffbdf48
Now running in RAM - U-Boot at: 0ffe0000
L2 cache 256KB: enabled
Using default environment

PCI Scan: Found Bus 0, Device 22, Function 0
PCI Scan: Found Bus 0, Device 23, Function 0

In:    serial
Out:   serial
Err:   serial
U-Boot relocated to 0ffe0000
Net:   No ethernet found.
### main_loop entered: bootdelay=1

### main_loop: bootcmd="bootm 0xffe80000;setenv verify no;autoscr 0x1700000
bootm fe6000f0"
Hit any key to stop booting:  0
## Booting image at ffe80000 ...
   Image Name:   netbsd
   Image Type:   PowerPC NetBSD Standalone Program (uncompressed)
   Data Size:    383216 Bytes = 374.2 kB
   Load Address: 00040000
   Entry Point:  00040004
   Verifying Checksum ...OK
   Watchdog Disabled
   Loading Standalone Application ...OK
Unit 0
Unit 1
Registering ethernet driver for unit 0
Registering ethernet driver for unit 1

None of the boot parameters are configured!!
So Booting from flash!!

You can use U-boot native networking facilities
============================================================



Hit any key to break into BOOT_USER mode:  0 < ------------- 任意のキーを押す
Starting F10 BLI Shell ...
BOOT_USER #

4.BOOT_USERプロンプトに「restore factory-defaults」コマンドを入力します

BOOT_USER #restore factory-defaults

Erasing NVRAM contents...
Successfully erased NVRAM contents
Erasing Filesystem sectors...

Successfully erased filesystem sectors
Erasing boot parameters...
Successfully erased boot parameters
Please reload for restore factory-defaults to take effect.

5.「reload」コマンドを入力して実行すると、S50N/Vシステムが工場出荷時のデフォルト設定で起動します(起動プロセス中にキーを押す必要はありません)

BOOT_USER #reload
!
!
Force10>
Force10>en
Force10#00:07:00: %STKUNIT0-M:CP %SEC-4-ENABLE_PASSW_NOT_CONFIGURED: Enable password is required for authentication but not configured
00:07:00: %STKUNIT0-M:CP %SEC-3-AUTHENTICATION_ENABLE_SUCCESS: Enable password authentication success  on console

 
6. これでスイッチが工場出荷時のデフォルトになり、ここから設定できます

Force10#config t
Force10(conf)#
 
Article Properties
Article Number: 000122552
Article Type: How To
Last Modified: 21 Feb 2021
Version:  3
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.