Skip to main content
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Create and access a list of your products

PowerVault TL2000 / TL4000 Tape Library - How to Upgrade the Firmware for the Tape Library and Tape Drives

Summary: This article provides information on how to upgrade the firmware for the Tape Library and Tape Drives for the PowerVault TL2000 / TL4000 Tape Library.

This article applies to This article does not apply to This article is not tied to any specific product. Not all product versions are identified in this article.

Symptoms

 

SLN156045_en_US__1icon Note: This article is part of the Dell PowerVault knowledge library, available here.

 

This article explains how to upgrade the firmware for the Tape Library and Tape Drives for the PowerVault TL2000 / TL4000 Tape Library.
Information and where to download ITDT can be found on this article
 

 

SLN156045_en_US__1icon Note: If at any time there is a complication, technical issue or some other issue, please contact Dell Technical Support for assistance. Contact is at the bottom of this page.

 

 

Table of content:

 

Tape Library Firmware Update Tape Drive Firmware Update

Preferred Method.Tape Library (Medium Changer) using the RMU (Remote Management Unit)


The following describes how-to upgrade or apply the TL2000 / TL4000 tape library (medium changer) firmware using the RMU:
  1. If the RMU or Web Interface is not configured, please use the following links to setup / configure the RMU:
  2. Using the IP Address configured to the RMU / Web Interface, connect to it using a web browser like - Internet Explorer®, Firefox®, or Chrome®.
  3. Once in the RMU / Web Interface, use the following menu path - Service Library > Upgrade Firmware
  4. Download the appropriate firmware from Dell's Support site.
  5. At this time, make sure that the backup software services are stopped. If necessary, stop and disable these services, and restart / reboot the server.
  6. After the firmware has been downloaded and extracted, go back to the RMU / Web Interface.

     

    SLN156045_en_US__1icon Note: Take note or remember the location of where the firmware files where downloaded and extracted.

     

  7. In the top center section of the page, you will see "Upgrade Library Firmware"  (Figure 1).

    SLN156045_en_US__41371834446892.TLxK_ITDT_Firmware_Update_RMU
    Figure 1: RMU Firmware Upgrade

     
  8. Select or click on "Browse" and browse to the locate where the Library Firmware file is located.
  9. Select the file, and once back to the Upgrade Firmware page, the "Update" button can be selected.
    If the button is "grayed-out", the "Update" button cannot selected, and this means that the Library Firmware was not selected.
  10. After the firmware has been upgraded for the tape library and/or tape drive(s) - it is highly recommended that the server be restart / rebooted.
  11. Once this is done, start the backup software services, and see how the backup software has engaged the tape library and/or tape drive(s).
  12. If the firmware for the tape library and/or tape drive(s) are not seen as updated, please engage the appropriate backup software vendor for technicial support regarding this issue.




 
 

Alternate Method. Tape Library (Medium Changer) using ITDT-SE

 

SLN156045_en_US__1icon Note: For either Windows® or Linux®, Java® is a required component for this installation of ITDT-DCR.

 

Supported JREs (Java Runtime Environment) are:

  • Java® 1.4.2_17 by Sun Microsystems and higher
  • Java® 1.4.2 SR11 by IBM Corporation and higher

     

The following describes how-to upgrade or apply the TL2000 / TL4000 tape library (medium changer) firmware using ITDT-DCR (Dell Customer Release):

 

  1. Download the appropriate firmware from Dell's Support site.
  2. At this time, make sure that the backup software services are stopped. If necessary, stop and disable these services, and restart / reboot the server.
  3. After the firmware has been downloaded and extracted, go to or browse to the location where the files where extracted.
  4. Use the README_itdt_dcr.txt for the installation procedure for both Windows® and Linux®.
  5. Select the Scan button, once ITDT-DCR is running.
  6. Select the tape library that you would like to update with the firmware.
  7. Browse to the location where the firmware files where extracted.
  8. Choose the appropriate tape library firmware file and click Open.
  9. When the firmware update has completed, ITDT-DCR should show a PASSED result next to the updated tape library (Figure 2).

     
  10. SLN156045_en_US__61371834828698.TLxK_ITDT_Firmware_Update
    Figure 2: ITDT-DCR Firmware Upgrade

     
  11. After the firmware has been upgraded for the tape library and/or tape drive(s) - it is highly recommended that the server be restarted / rebooted.
  12. Once this is done, start the backup software services, and see how the backup software has engaged the tape library and/or tape drive(s).
  13. If the firmware for the tape library and/or tape drive(s) are not seen as updated, please engage the appropriate backup software vendor for technicial support regarding this issue.
 

Preferred Method. Tape Drive(s) Using ITDT-DCR

 

 

SLN156045_en_US__1icon Note: For either Windows® or Linux®, Java® is a required component for this installation of ITDT-DCR.

 

Supported JREs (Java Runtime Environment) are:

  • Java® 1.4.2_17 by Sun Microsystems and higher
  • Java® 1.4.2 SR11 by IBM Corporation and higher

     

The following describes how-to upgrade or apply the TL2000 / TL4000 tape drive(s) firmware using ITDT-DCR (Dell Customer Release):

 

  1. Download the appropriate firmware from Dell's Support site.
  2. At this time, make sure that the backup software services are stopped. If necessary, stop and disable these services, and restart / reboot the server.
  3. After the firmware has been downloaded and extracted, go to or browse to the location where the files where extracted.
  4. Use the README_itdt_dcr.txt for the installation procedure for both Windows® and Linux®.
  5. Select the Scan button, once ITDT-DCR is running.
  6. Select the drive that you would like to update with the firmware.
  7. Browse to the location where the firmware files where extracted.
  8. Choose the appropriate tape drive firmware file for that tape drive and click Open.
  9. When the firmware update has completed, ITDT-DCR should show a PASSED result next to the updated drive (Figure 2 - above).
  10. After the firmware has been upgraded for the tape library and/or tape drive(s) - it is highly recommended that the server be restarted / rebooted.
  11. Once this is done, start the backup software services, and see how the backup software has engaged the tape library and/or tape drive(s).
  12. If the firmware for the tape library and/or tape drive(s) are not seen as updated, please engage the appropriate backup software vendor for technicial support regarding this issue.


 


Alternate Method. Tape Drive(s) using the RMU (Remote Management Unit)

 

SLN156045_en_US__1icon Note: Upgrading the tape drive through the RMU, generally takes about 5 minutes. However, it can take longer, and some times can fail more than using the Preferred Method listed above.

 

The following describes how-to upgrade or apply the TL2000 / TL4000 tape drive(s) firmware:
 

  1. If the RMU or Web Interface is not configured, please use the following links to setup / configure the RMU:
  2. Using the IP Address configured to the RMU / Web Interface, connect to it using a web browser like - Internet Explorer®, Firefox®, or Chrome®.
  3. Once in the RMU / Web Interface, use the following menu path - Service Library > Upgrade Firmware.
  4. Download the appropriate firmware from Dell's Support site.
  5. At this time, make sure that the backup software services are stopped. If necessary, stop and disable these services, and restart / reboot the server.
  6. After the firmware has been downloaded and extracted, go back to the RMU / Web Interface.
  7. In the top center section of the page, you will see "Upgrade Drive"  (Figure 1).


    SLN156045_en_US__91371834688835.TLxK_ITDT_Firmware_Update_RMU
    Figure 1: RMU Firmware Upgrade

     
  8. Select or click on "Browse" and browse to the locate where the Library Firmware file is located.
  9. Select the file, and once back to the Upgrade Firmware page, the "Update" button can be selected.
    If the button is "grayed-out", the "Update" button cannot selected, and this means that the Library Firmware was not selected.
  10. After the firmware has been upgraded for the tape library and/or tape drive(s) - it is highly recommended that the server be restart / rebooted.
  11. Once this is done, start the backup software services, and see how the backup software has engaged the tape library and/or tape drive(s).
  12. If the firmware for the tape library and/or tape drive(s) are not seen as updated, please engage the appropriate backup software vendor for technicial support regarding this issue.

Cause

-

Resolution

-

Affected Products

Servers, PowerVault TL2000, PowerVault TL4000
Article Properties
Article Number: 000130520
Article Type: Solution
Last Modified: 22 Sept 2021
Version:  5
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.