Skip to main content
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Create and access a list of your products

如何在 Dell EMC Force10 S4810、S4820T、Z9000、Z9500、S6000、S60、S55 和 S5000 交换机上恢复出厂默认值

Summary: 如何在 Dell Networking Force10 S4810、S4820t、Z9000、Z9500、S6000、S60、S55 和 S5000 交换机上恢复出厂默认值。

This article applies to This article does not apply to This article is not tied to any specific product. Not all product versions are identified in this article.

Instructions



本文介绍如何在 Dell Networking Force10 S4810 上恢复出厂默认值。
 


需要记住的要点 

  • 当您恢复堆栈中的所有设备时,这些设备将处于独立模式。
  • 当您恢复堆栈中的单个设备时,只有此设备将处于独立模式。堆栈中的其它设备不会受到影响。
  • 当您在独立模式下恢复设备时,恢复后设备将保持独立模式。
  • 恢复完成后,设备立即重新启动。
 


用于恢复出厂默认值的命令

   
恢复出厂默认值将删除现有的永久设置(配置、堆栈、扇出等)。恢复后,设备将立即重新开启。谨慎行事!

 

命令

参数

FTOS# restore factory-defaults stack-unit {0-5 | all} {bootvar | clear-all | nvram}

恢复和清除配置、堆栈、扇出等..
0-5 - 指示要重置为出厂默认值的交换机的编号
all - 指示所有交换机将重置为出厂默认值
Bootvar - 重置启动环境变量
Clear-all - 重置 BootVar、NvRam 和配置
NvRam - 重置 NvRam

 

HOW10777_en_US__1icon 注:此命令功能在固件版本 8.3.3.9 中引入。您将需要有 8.3.3.9 或更高版本的固件,才能使用此命令选项。  

示例 

重置所有堆栈设备的示例:
FTOS#restore factory-defaults stack-unit all nvram
**************************************************************
* Warning - Restoring factory defaults will delete the existing *
* startup-config and all persistent settings (stacking, fanout, etc.)*
* All the units in the stack will be split into standalone units. *
* After restoration the unit(s) will be powercycled immediately. *
* Proceed with caution !
***************************************************************
Proceed with factory settings? Confirm [yes/no]:yes
-- Restore status --
Unit Nvram Config
------------------------
0 Success Success
1 Success Success
2 Success Success
3 Not present
4 Not present
5 Not presentPower
Power-cycling the unit(s).
 
重置单个交换机的示例
 
FTOS#restore factory-defaults stack-unit 1 nvram
*************************************************************
*Warning - Restoring factory defaults will delete the existing *
* persistent settings (stacking, fanout, etc.) *
* After restoration the unit(s) will be powercycled immediately. *
* Proceed with caution ! *
**************************************************************
Proceed with factory settings? Confirm [yes/no]:yes
-- Restore status --
Unit Nvram Config
------------------------
1 Success
Power-cycling the unit(s)

Affected Products

PowerSwitch S4810P, PowerSwitch S5000, Force10 S55T, Force10 S60-44T, PowerSwitch S6000, PowerSwitch S6000 ON, Force10 Z9000, Dell Networking Z9500
Article Properties
Article Number: 000103011
Article Type: How To
Last Modified: 16 Sep 2021
Version:  4
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.