Skip to main content
  • Place orders quickly and easily
  • View orders and track your shipping status
  • Enjoy members-only rewards and discounts
  • Create and access a list of your products

Basic Command Line Interface on Dell Networking PowerConnect 2800 model switches

Summary: Details of the limited amount of commands available through the command line on Dell Networking PowerConnect 2800 switches.

This article applies to This article does not apply to This article is not tied to any specific product. Not all product versions are identified in this article.

Instructions

This article discusses the limited amount of commands available through the command line on Dell Networking PowerConnect 2800 model switches.

 


Basic CLI Overview

The PowerConnect 28xx series supports a basic console CLI interface and a single telnet session.
 
HOW10655_en_US__1icon In order to access the serial console, the switch must be in managed mode. By default the switch is in unmanaged mode. Refer to article HOW10276 "How to access Management for the PowerConnect 2800 series switches"  if not familiar with switching to managed mode. The 2808 model does not have a serial port for console connection. Because of that the 2808 does not have the command line functionality like the rest of the 2800 model switches.

 

The CLI can be used to :
  • Reboot the device
  • Restore the system to default (except 2808 has to be reset from the Web interface)
  • Download or upload a configuration, image, or boot file
  • Create a local database users (for device management)
  • Define an SNMP Community
  • Define a static IP address
  • execute the show tech-support command
 
 

Reboot the Device

# reload

This command will reset the whole system and disconnect your current session. Do you want to continue ? (Y/ console N)[N] Y
Shutting down ...
Shutting down ...
 

Restore the system Default

 
After a reload and while the switch is booting up you will see the option to hit "enter" to stop autoboot and enter the boot menu.
At the boot menu, choose [2] Erase Flash File by pressing <2> and then confirm by pressing <Y>
            Startup Menu
 
[1]  Download Software
[2]  Erase Flash File
[3]  Enter Diagnostic Mode
[4]  Set Terminal Baud-Rate
[5]  Back
Enter your choice or press 'ESC' to exit: 2
Warning! About to erase a Flash file.
 
Are you sure (Y/N) ? y 
 

Upgrade Firmware

Type copy tftp://{TFTP Server IP Address}/{filename of firmware} image to pull the image file from the TFTP server.

console# copy tftp://10.0.0.2/ -10020 powerconnect_28xx.ros image

16-Dec-2008 14:35:59 %COPY-I-FILECPY: Files Copy - source URL tftp://10.0.0.2/powerconnect_28xx-10020.ros destination URL flash://image
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!16-Dec-2008 14:39:07 %COPY-W-TRAP: The copy operation was com
pleted successfully
!
Copy: 4606156 bytes copied in 00:03:37 [hh:mm:ss]
 
console# 
 

Create a local database of users

console# configure
console(config)# username admin password password level 15
console(config)# 
 

SNMP Configuration

console# configure
console(config)# snmp-server community public rw 10.37.123.10
console(config)# 
 

IP Address Assignment

console# configure
console(config)# ip address 172.16.1.1 /24
console(config-if)#
 
 

Show Tech-Support

 
 Console# show tech-support
                

Affected Products

PowerConnect 2816, PowerConnect 2824, PowerConnect 2848
Article Properties
Article Number: 000120225
Article Type: How To
Last Modified: 21 Feb 2021
Version:  4
Find answers to your questions from other Dell users
Support Services
Check if your device is covered by Support Services.