Article Number: 000118094
명령 | 목적 |
Force10# configure |
구성 모드로 들어갑니다. |
Force10(conf)# protocol spanning-tree rstp |
RSTP 구성 모드를 입력합니다. |
Force10(conf-rstp)# bridge-priority 4096 (primary peer) Force10(conf-rstp)# bridge-priority 8192 (secondary peer) |
*선택 사항: RSTP 브리지 우선 순위를 구성합니다.*이러한 우선 순위는 VLT 쌍에 고유하지 않으며 기본에 대한 기본 설정을 표시하는 데 사용됩니다. 기본 브리지가 루트 브리지로 지정되지 않도록 4096의 배수를 사용합니다. |
Force10(conf-rstp)# no disable |
스패닝 트리 프로토콜을 활성화합니다. |
명령 | 목적 |
Force10# configure |
구성 모드로 들어갑니다. |
Force10(conf)# interface range fortyGigE 0/56 , fortyGigE 0/60 |
인터페이스 구성 모드로 들어갑니다. 쉼표 앞뒤의 공백에 유의하십시오. |
Force10(conf-if-range-fo-0/56,fo-0/60)# no shutdown |
인터페이스의 범위를 활성화합니다. |
Force10(conf-if-range-fo-0/56,fo-0/60)# interface port-channel 100 |
포트 채널 구성 모드로 들어갑니다. |
Force10(conf-if-po-100)# channel-member fortyGigE 0/56,60 |
포트 채널에 물리적 인터페이스를 추가합니다. |
Force10(conf-if-po-100)# no shutdown |
포트 채널을 활성화합니다. |
명령 | 목적 |
Force10# configure |
구성 모드로 들어갑니다. |
Force10(conf)# vlt domain 1 |
도메인 ID 1-1000에 대한 VLT 도메인 구성 모드로 들어갑니다. |
Force10(conf-vlt-domain)# primary-priority 10 (primary peer) Force10(conf-vlt-domain)# primary-priority 20 (secondary peer) |
*선택 사항: 각 피어 스위치에 대한 VLT 우선 순위를 지정합니다. 1-65535(가장 높은 우선 순위부터) |
Force10(conf-vlt-domain)# back-up destination 1.1.1.2 (primary peer) Force10(conf-vlt-domain)# back-up destination 1.1.1.1 (secondary peer) |
피어 스위치의 관리 IP 주소를 지정합니다. 피어 시스템 상태를 모니터링하는 하트비트가 설정됩니다. |
Force10(conf-vlt-domain)# peer-link port-channel 100 |
VLTi LAG를 VLT 도메인에 연결합니다. |
Force10(conf-vlt-domain)# system-mac <mac-address>또한 VLT 피어 스위치에 동일한 MAC 주소를 구성합니다. 이 명령은 피어 스위치 중 하나가 재부팅될 때 VLT 시스템에서 두 피어 스위치에 대한 VLT 도메인의 기본 MAC 주소를 동기화하는 데 필요한 시간을 최소화하기 위해 사용됩니다.
명령 | 목적 |
Force10# configure |
구성 모드 입력 |
Force10(conf)# interface tengigabit 0/20 |
인터페이스 구성 모드로 들어갑니다. |
Force10(conf-if-te-0/20)# port-channel-protocol lacp |
LACP 구성 모드로 전환 |
Force10(conf-if-te-0/20-lacp)# port-channel 20 mode active |
LACP LAG에 대해 포트 채널을 "mode active"로 설정합니다. |
Force10(conf-if-te-0/20-lacp)# interface port-channel 20 |
포트 채널 구성 모드 시작 |
Force10(conf-if-po-20)# portmode hybrid |
포트 모드 하이브리드를 사용하면 인터페이스에서 태그가 지정된 트래픽과 태그가 지정되지 않은 트래픽을 전달할 수 있습니다. |
Force10(conf-if-po-20)# switchport |
Switchport는 인터페이스를 레이어 2 모드로 전환합니다. |
Force10(conf-if-po-20)# vlt-peer-lag port-channel 20 |
포트 채널을 VLT 포트 채널로 할당 |
Force10(conf-if-po-20)#end |
구성 모드 종료 |
Force10# write |
구성 저장 |
Force10# show vlt brief VLT Domain Brief ------------------------------------------------- Domain ID: 1 Role: Primary Role Priority: 10 ICL Link Status: Up Heartbeat Status: Up VLT Peer Status: Up Local System MAC address: 00:01:e8:8b:19:37 Remote System MAC address: 00:01:e8:8b:18:b9 Configured System MAC address: aa:11:22:33:44:55
Force10# show vlt brief VLT Domain Brief ------------------------------------------------- Domain ID: 1 Role: Secondary Role Priority: 20 ICL Link Status: Up Heartbeat Status: Up VLT Peer Status: Up Local System MAC address: 00:01:e8:8b:18:b9 Remote System MAC address: 00:01:e8:8b:19:37 Configured System MAC address: aa:11:22:33:44:55
Force10# show vlt statistics ----------------------------------------------------- HeartBeat Messages Sent: 95446 HeartBeat Messages Received: 95440 ICL Hello's Sent: 95420 ICL Hello's Received: 95414 Domain Mismatch Errors: 0 Version Mismatch Errors: 0 Config Mismatch Errors: 0VLT 백업 링크: 상태 확인:
Force10# show vlt backup-link VLT Backup Link -------------------------------------------------- Destination: 1.1.1.2 Peer HeartBeat status: Up HeartBeat Timer Interval: 1 HeartBeat Timeout: 3 UDP Port: 34998 HeartBeat Messages Sent: 95305 HeartBeat Messages Received: 95299
Force10# show vlt backup-link VLT Backup Link -------------------------------------------------- Destination: 1.1.1.1 Peer HeartBeat status: Up HeartBeat Timer Interval: 1 HeartBeat Timeout: 3 UDP Port: 34998 HeartBeat Messages Sent: 95305 HeartBeat Messages Received: 95299
Force10# show vlt mismatch
22 Mar 2024
5
How To