Přeskočit na hlavní obsah
Odhlásit

Vítejte ve společnosti Dell.

Můj účet
  • Vkládejte objednávky snadno a rychle
  • Zobrazit objednávky a sledovat stav expedice
  • Vytvořte a přistupujte k seznamu svých produktů
Přihlásit se Vytvořte si účet Přihlášení na stránky Premier Přihlášení do partnerského programu
Některá čísla článků se možná změnila. Pokud zde není to, co hledáte, zkuste vyhledat všechny články. Hledat články

Latitude 3400 Removal Guide for Customer Replaceable Units

Shrnutí: A guide to safe removal and replacement of those parts of a Latitude 3310 notebook that Dell considers safe and easy for anyone to attempt

Tento článek se vztahuje na Tento článek se nevztahuje na Tento článek není vázán na žádný konkrétní produkt. V tomto článku nejsou uvedeny všechny verze produktu.
Podívejte se na další zdroje

Příznaky

These guides will take you step by step through the safe removal of what are considered to be the Customer Replaceable Unit (CRU) parts of a Dell Latitude 3400 system. (CRUs are the parts of the system that shouldn't need an engineer to remove or replace.) The guides will also include pictures to reference what's involved.

Table of Contents:

  1. CRU Removal Guide
  2. Removal Instructions

 

Removal Guide

 

If these guides do not cover what you are looking to do, then you will want to reference your System Manual.

The article below provides information on safe practises to take into consideration before working with electrical equipment.


Back to Top

 

Příčina

Removal Instructions

 

Note: Please click on the title of the section you want to open below, in order to see the contents.
 
|

 

SLN320627_en_US__2ReqTools_E7450_BKeith_01

1 Small Phillip's head screwdriver 2 Plastic Scribe
3 Small Flat head screwdriver    
 
Note: Be aware that using a large Phillips or Flat Head screwdriver may result in damage to the head of the screws. This would make their removal impossible without speciality tools, that aren't available to our onsite engineers.

 

  1. Pre-Removal Instructions Before removing the Base Cover :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

  2. Loosen the nine captive screws that secure the base cover to the palmrest and keyboard assembly.

SLN320627_en_US__4Lat3400_Base1

  1. Pry the base cover and continue to open the right side of the base cover.

SLN320627_en_US__5Lat3400_Base2

  1. Lift the right side of the base cover [1], and remove it off the palmrest and keyboard assembly [2].

SLN320627_en_US__6Lat3400_Base3

 

  1. Pre-Removal Instructions Before removing the Battery :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Base Cover

  2. Disconnect the battery cable from the system board.

SLN320627_en_US__7Lat3400_3500_Battery1

  1. Remove the four (M2x3) screws that secure the battery to the palmrest and keyboard assembly [1].

  1. Lift the battery off the palmrest and keyboard assembly [2.

SLN320627_en_US__8Lat3400_3500_Battery2

 

  1. Pre-Removal Instructions Before removing the Memory Modules :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Base Cover and disconnect the Battery cable

  2. Pry the clips securing the memory module until the memory module pops-up [1].

  1. Remove the memory module from the memory module slot [2].

SLN320627_en_US__9Lat3400_3500_Memory1

 

  1. Pre-Removal Instructions Before removing the WLAN Card :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Base Cover and disconnect the Battery cable

  2. Remove the single (M2x3) screw that secures the WLAN card bracket to the system board [1].

  1. Slide and remove the WLAN card bracket that secures the WLAN cables [2].

  1. Disconnect the WLAN cables from the connectors on the WLAN card [3].

  1. Lift the WLAN card away from the connector [4].

SLN320627_en_US__10Lat3400_3500_WLAN

 

  1. Pre-Removal Instructions Before removing the Hard Drive :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Base Cover and disconnect the Battery cable

  2. Disconnect the hard drive cable from the system board [1].

  1. Peel the tape that secures the hard drive cable to the system board [2].

SLN320627_en_US__11Lat3400_3500_HDD1

  1. Remove the four (M2x4.5) screws that secure the hard drive assembly to the palmrest and keyboard assembly [1].

  1. Lift the hard drive from the slot on the palmrest and keyboard assembly [2].

SLN320627_en_US__12Lat3400_3500_HDD2

 

  1. Pre-Removal Instructions Before removing the Solid-state drive/Intel Optane memory module :

    1. During installation or removal of any hardware always ensure all data is backed up properly

    2. Disconnect any telephone, network, or USB cables from the computer

    3. Disconnect the computer and all attached devices from their electrical outlets

    4. Please remove the Base Cover and disconnect the Battery cable

  2. Remove the single (M2x3) screw that secures the thermal plate to the palmrest and keyboard assembly [1].

  1. Turn the thermal plate over [2].

  1. Slide and remove the thermal plate from the solid-state drive/Intel Optane card slot [3.

SLN320627_en_US__13Lat3400_3500_SSD1

  1. Remove the single (M2x2) screw that secures the solid-state drive/Intel Optane card to the palmrest and keyboard assembly [1].

  1. Slide and lift the solid-state drive/Intel Optane card off the palmrest and keyboard assembly [2].

SLN320627_en_US__14Lat3400_3500_SSD2

Řešení

 

If you require further assistance, please contact Technical Support

 

  Contact Us  

Dotčené produkty

Latitude 3400
Vlastnosti článku
Číslo článku: 000132821
Typ článku: Solution
Poslední úprava: 11 Nov 2022
Verze:  5
Najděte odpovědi na své otázky od ostatních uživatelů společnosti Dell
Služby podpory
Zkontrolujte, zda se na vaše zařízení vztahují služby podpory.