Do not turn off your computer or disconnect from the power source while updating the BIOS as this could harm your computer. During the update, your computer will restart and you may briefly see a black screen.
Before updating, please read the installation instructions and important information noted below.
Dell OptiPlex System BIOS, A03
OTOMATİK OLARAK YÜKLENDİ Bu dosya son güncellemenin bir parçası olarak otomatik olarak yüklendi. Herhangi bir sorun yaşıyorsanız, manuel olarak indirip yeniden yükleyebilirsiniz.Uyumluluğu kontrol edin
Sisteminize yönelik en son sürücü bilgilerini görüntülemek için lütfen ürün ayrıntılarınızı girinDell Servis Etiketinizi veya modelinizi girin
Ürününüzü aramak mı istiyorsunuz? Bir ürün tanımlayıcısı girin. Nasıl yapılacağını göster
Bu sürücü, seçilen ürün için geçerli değildir. Ürün ayrıntılarınızı yeniden girmek için başka bir ürün seçin veya farklı bir ürüne yönelik tüm sürücüleri görüntülemek için Ürün Desteği sayfasını ziyaret edin.
Daha fazla güncelleme bulun. SupportAssist'i kullanarak aygıtınız için en son sürücü güncellemelerini bulun.
Fixes & Enhancements
1. Fix to the modbay IDE support during device swapping.
2. Alter USB code to allow faster USB device configuration and detection,
disable USB floppy boot if DISKETTE A: is set to "Not Installed",
and better support Bonzai, and other Non-DELL USB disk devices.
3. Updated support for newer Processors.
4. Fix to configuring modbay IDE devices during a S3 resume.
5. Updated intgrated video BIOS to correct an issue with full screen
text mode switching and an issue with some LCD monitors and the
DVI riser card.
6. Allow use of E000h area for upper memory managers.
7. Added support for 48-bit LBA hard drives (> 137 GB).
8. Fixed system shutdown in some C-A-D cases.
9. Fixed error in PNP BIOS function get_SMBIOS_information (0x50).
10. Properly set system power state when AC Power is lost in S3.
11. Prevent system hang condition when placed in a 10Mbit high
traffic environment.
12. Eliminated rare, nonrepeatable RTC and memory boot failures.
13. Enable USB Floppy/HDD access to paged memory.
14. Added RPL Network boot and updated PXE Boot to work better on Cisco switches.
15. Fixed intermittent missing 2nd virtual CPU on HyperThreading processors.
16. Updated to memory POST code to prevent false errors.
17. Corrected the IDE Drive Diagnostic status text.
18. Alter ACPI code to work better with Windows 98.
Version
Sürüm tarihi
İndirme Türü
Kategori
Önem
Optionalİndirdiğinizde, Dell Software Lisans Sözleşmesi’nin koşullarını kabul etmiş olursunuz.
Important Information
- The Floppy Format is recommended for most users. Floppy format creates a bootable self-extracting disk.
- The Non-packaged Format is intended for advanced users that only require the bootable disk.
Installation Instructions
Floppy Format
Creating the disk:
This procedure requires one blank, formatted 3.5-inch floppy disk. Label the disk BIOS.
- Click Download now from the Download and install section, to begin.
The File Download window appears. - Click Save this program to disk.
- In the Save in: section, click the down arrow and click to select Desktop as the location then click Save.
- When the file download is complete, click Close button.
Close all open windows. - Double-click the down loaded file SX260A03.EXE on your Desktop.
If the Security Warning window appears, click Yes. - Click the Setup button.
A black MS-DOS window appears. - Press the <Enter> key.
- Insert a formatted floppy disk in the floppy disk drive and press the <Enter> key.
- Press the <Y> key to begin copying files.
The message End of the disk set appears. - Press the <Enter> key.
- Click the Start button,
- Click the Run button.
- Type a: in
the Open box and click OK.
A list of files on the floppy disk appears. - Close all open windows and leave the disk in the floppy drive.
Skip to the section Flashing the BIOS below.
If you are creating this disk on another computer, remove the disk. Then insert it into the system that needs the BIOS flashed, and resume the procedure.
Return to Top
Non-Packaged Format
Creating the disk:
This procedure requires one blank, formatted 3.5-inch floppy disk. Label the disk BIOS.
- Click Download now from the Download and install section, to begin.
The File Download window appears. - Click Save this program to disk.
- In the Save in: section, click the down arrow and click to select Desktop as the location then click Save.
- When the file download is complete, click Close button.
Close all open windows. - Insert a blank, bootable, formatted 3.5-inch floppy disk.
- Right-click the downloaded file, point to Send Tothen click to select 3 1/2 Floppy (a), and skip to the section Flashing the BIOS
below.
Return to Top
Flashing the BIOS
NOTICE:
Changing the system BIOS may result in unintended side affects, such as
incompatibility of the new BIOS with installed hardware. If problems arise
after a BIOS change, it may be necessary to return the system to the
original version of the BIOS.
- If you are flashing the BIOS on a portable computer, be sure that
the AC adapter is plugged in and the computer is not operating on battery
power. - Ensure that the Flash BIOS disk is inserted into the floppy disk
drive. - Click the Start button, click Shut Down, click
Restart, then click OK.
The computer will restart
and boot to the floppy disk.
NOTE:
If the flash BIOS