INSTALATE AUTOMATAcest fișier a fost instalat automat ca parte a unei actualizări recente. Dacă întâmpinați orice probleme, puteți descărca și reinstala manual.
Conținutul acestei pagini este posibil să fi fost tradus automat. Pentru a furniza feedback, completați formularul din partea de jos a paginii.
Acest fișier a fost instalat automat ca parte a unei actualizări recente. Dacă întâmpinați orice probleme, puteți descărca și reinstala manual.
This utility disables the read-lookahead (ESP) feature of the drive.
Recomandate
Verificați compatibilitatea
Introduceți detaliile produsului pentru a vedea cele mai recente informații despre driverele sistemului dvs.
Introduceți eticheta de service Dell sau modelul
Doriți să vă căutați produsul? Introduceți un identificator de produs.Arătați-mi cum
Nu s-a găsit niciun rezultat.Nu am găsit nimic pentru căutarea dvs. Modificați căutarea pentru a introduce o etichetă de service (B959FS3) sau un model (Latitude 5540) și încercați din nou.
This driver is not compatible
This driver is not applicable for the selected product. Choose another product to re-enter your product details for this driver or visit the Product Support page to view all drivers for a different product.
Conectați-vă la Windows ca administrator pentru a utiliza scanarea automată. Dacă sunteți deja conectat ca administrator și vedeți acest mesaj, reporniți sistemul.Sistemul dvs. este gestionat de către administratorul IT, iar caracteristicile pot fi limitate.
Găsiți mai multe actualizări. Utilizați SupportAssist pentru a găsi cele mai recente actualizări ale driverelor pentru dispozitivul dvs.
Fixes & Enhancements
Initial Release A timeout problem was reported with Maxtor Atlas 15K SCSI hard disk drives running a specific Hard Drive Stress test script under Linux 9.0 within a PE1600SC system. When the Messages log file within Linux is viewed, a System Timeout, Bus Reset, and 04/40/0C check condition may be recorded.
This issue was found while running the Hard Drive stress test. There is no known customer reported problem running a specific application. In this test environment, the drive is requested to perform reverse sequential reads. In some cases, this issue can intermittently create an internal race condition causing the the drive to ‘hang’, requiring the Operating system to issue a bus reset.
Dell Technologies recommends reviewing this update to determine if it applies to your system. The update contains changes that impact only certain configurations or provides new features that may or may not apply to your environment.
Format fișierOne or more self extracting disk images inside of a self extracting zip
Nume fișier:BR67588.exe
Dimensiune fișier:881.34 KB
Acesta este un fișier mare. În funcție de viteza conexiunii, descărcarea poate dura mai mult timp.
Descriere format:
This file contains a compressed (or zipped) set of files. Download the file to a folder on your hard drive, then double-click it to unzip the set of files. Follow the instructions to complete the installation.
Utility must be placed on a non-write protected diskette.
NOTE: In order to create this diskette, the file must be downloaded to and executed on a system running Microsoft Windows.
Download 1. Click the "Download Now" link to download the file. 2. If the Export Compliance Disclaimer window appears, click the "I agree" link to accept the agreement. 3. When the File Download window appears, click "Save" to save the file to your hard drive.
Diskette Creation 1. Browse to the location where you downloaded the file and double-click the new file to create the diskette set. 2. Insert a blank diskette then click Continue. 3. After all the files have been copied to the last, click Finish.
Installation: NOTE: BACKUP ALL DATA BEFORE RUNNING THIS PROGRAM. Do not remove power from the devices or disturb the devices in any way while the download is in progress. Dell, Inc is not Responsible for any data loss resulting from the use of this program
NOTE: Before proceeding with the update, refer to README.TXT file, section 4.0 "Using The Update Utility" for important information regarding the update process.
For drives connected to an LSI 1020 or 1030 SCSI controller: 1. Insert the firmware update diskette into the floppy drive and reboot the system. 2. The utility will automatically determine the correct device to update when booted 3. Once the update is complete Remove the diskette and reboot the system.
For drives connected to an Adapted 7899 or 39160 SCSI controller: 1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line Device=ASPIDRV\ASPI8U2.SYS and adding the ‘REM’ statement to the line Device=ASPIDRV\ASPIMPT.SYS. This modification loads the ASPI driver for Adaptec controllers instead of the ASPI driver for LSI controllers 2. Insert the firmware update diskette into the floppy drive and reboot the system. 3. The utility will automatically determine the correct device to update when booted 4. Once the update is complete Remove the diskette and reboot the system.
For drives connected to Channel 0 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC): 1. Insert the firmware update diskette into the floppy drive and reboot the system. 2. The utility will automatically determine the correct device to update when booted 3. Once the update is complete Remove the diskette and reboot the system.
For drives connected to Channel 1 of an LSI RAID controller (PERC 3/SC, PERC 3/DC, PERC 3/DCL, PERC 3/QC, PERC 4/Di, PERC 4/SC, PERC 4/DC): 1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line “Device=ASPIDRV\MEGASPI.SYS /a1” and adding the REM statement to the line “Device=ASPIDRV\MEGASPI.SYS /a0”. 2. Insert the firmware update diskette into the floppy drive and reboot the system. 3. The utility will automatically determine the correct device to update when booted 4. Once the update is complete Remove the diskette and reboot the system.
For drives connected an Adaptec RAID controller (PERC 3/Si, PERC 3/DI): 1. Modify the CONFIG.SYS file on the diskette by removing the 'REM' statement in the line "Device=ASPIDRV\ELITEAPI.SYS /M" and adding the ‘REM’ statement to the lines “Device=ASPIDRV\MEGASPI.SYS /a0” and “Device=ASPIDRV\MEGASPI.SYS /a1”. 2. Insert the firmware update diskette into the floppy drive and reboot the system. 3. The utility will automatically determine the correct device to update when booted 4. Once the update is complete Remove the diskette and reboot the system.