Need TPM Support?
For additional helpful information, please refer to our Knowledge Base. View article.Dell TPM 2.0 Update Utility
Újraindítás szükséges AUTOMATIKUSAN TELEPÍTETT Ez a fájl automatikusan települt egy korábbi frissítés részeként. Ha bármilyen problémát tapasztal, manuálisan letöltheti és újratelepítheti.Lehet, hogy az oldal tartalma gépi fordítás útján lett fordítva. Visszajelzés küldéséhez töltse ki az oldal alján található űrlapot.
This package contains the Dell TPM 2.0 Firmware Update Utility. Trusted Platform Module (TPM) is a hardware chip on the system motherboard to provide enhanced security..
Ajánlott
Kompatibilitás ellenőrzése
Kérjük, adja meg a termék adatait a rendszeréhez tartozó legfrissebb illesztőprograminformációk megtekintéséhez.Adja meg Dell-szervizcímkéjét vagy -modelljét
Szeretné kikeresni termékét? Adjon meg egy termékazonosítót. Mutasd meg, hogyan!
This driver is not compatible
This driver is not applicable for the selected product. Choose another product to re-enter your product details for this driver or visit the Product Support page to view all drivers for a different product.
Az automatikus ellenőrzés használatához jelentkezzen be a Windowsba rendszergazdaként. Ha már bejelentkezett rendszergazdaként, és látja ezt az üzenetet, kérjük, indítsa újra a számítógépet. A rendszert az IT-rendszergazda kezeli, és előfordulhat, hogy a funkciók köre korlátozott.
További frissítések. A SupportAssist segítségével megtalálhatja az eszközéhez elérhető legújabb illesztőprogram-frissítéseket.
Fixes & Enhancements
- Initial Release.
További információVerziószám
1.3.0.1, 1.3.0.1
Kibocsátás dátuma
12 jan. 2016
Letöltés típusa
Firmware
Kategória
Biztonság
Fontosság
OptionalDell Technologies recommends reviewing this update to determine if it applies to your system. The update contains changes that impact only certain configurations or provides new features that may or may not apply to your environment.
Elérhető formátumok View Important Information
Fájlformátum: CPG BIOS Executable for Windows/DOS
Fájlnév: DellTpm2.0_Fw1.3.0.1.exe
Fájlméret: 615.41 KB
Ez egy nagy fájl. A kapcsolat sebességétől függően a letöltés eltarthat egy ideig.
Formátum leírása:
This file format consists of a BIOS executable file. The Universal (Windows/MS DOS) format can be used to install from any Windows or MS DOS environment.
A letöltés integritásának biztosítása érdekében ellenőrizze az ellenőrző összeg értékét.
MD5:
077b18aeff636fceeaf75e8ecb66bec5
SHA1:
8d789530ce4bcb13c71a30d3a607fa7e7c64126d
SHA-256:
8910b0dce8c13ea2ced3f8bd5daa68c71abf379990c4ad6acb206930de2af0e4
A letöltéssel Ön elfogadja a Dell szoftverlicenc-szerződés feltételeit.
Fontos tudnivalók
This utility updates the system TPM 2.0 firmware to the new revision. If the utility is run on a system with TPM 1.2, it can switch the TPM mode to TPM 2.0. Switching the TPM mode may have operating system implications.
Támogatott operációs rendszerek
MS-DOS
Windows 7 (32 bites)
Windows 7, 64-bit
Windows 8 (32 bites)
Windows 8, 64-bit
Windows 8.1 (32 bites)
Windows 8.1 (64 bites)
Windows 10 (32 bites)
Windows 10, 64-bit
A következőre vonatkozik:
Dell TPM Firmware Update
Telepítési utasítások
Note 1: You must provide a bootable DOS USB drive. This executable file does not create the DOS system files.
Note 2 : Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 3: The TPM must be ON and Enabled in BIOS Setup, and the TPM must not be owned. If the TPM is owned, go to BIOS Setup and clear the TPM before proceeding. You may need to run TPM.msc to reinitiate the TPM under Windows operating system.
Note 4: When the TPM ownership is cleared, some operating system will automatically take ownership of the TPM on the next boot (TPM AutoProvisioning). This feature needs to be disabled in the operating system to proceed with the update.
Dell TPM Update Utility for Windows/DOS
Download
1. Click Download File.
2. When the File Download window is displayed, click Save to save the file to your hard drive.
Clear the TPM (See Notes 2, 3 and 4)
1. Before running the TPM update utility, clear the TPM Owner.
Disable TPM Auto Provisioning in Windows (See Note 4)
1. Boot to Windows
2. Launch the PowerShell Command window in Administrator mode
3. At the Powershell command prompt, start the command:
> Disable-TpmAutoProvisioning
4. Confirm the following results:
- AutoProvisioning: Disabled
5. Reboot the system, to BIOS Setup by pressing F2.
6. Navigate to Security > TPM 1.2/2.0 Security.
7. Click the Clear checkbox and select Yes at the prompt to clear the TPM settings. (You can skip it if the item is grayed out)
8. Click Exit to save changes.
9. Reboot system to Windows.
10. Confirm the TPM is not owned. The TPM should no longer be automatically provisioned by Windows.
11. When the TPM update is finished, launch the PowerShell command in Administrator mode to re-enable the auto provisioning.
> Enable-TpmAutoProvisioning
12. Confirm the following results:
- AutoProvisioning: Enabled
Updating the TPM update utility from Windows environment
1. Browse to the location where you downloaded the file and double-click the new file.
2. Windows System auto restarts and updates the TPM during the system startup.
3. When the TPM update is finished, the system auto reboots to take effect.
Updating the TPM update utility from DOS environment, with Legacy Boot mode (Non-Windows users)
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system, then Press F12 key and Select USB Storage Device and Boot to DOS prompt.
3. Run the file by typing copied file name where the executable file is located.
4. DOS system auto restarts and updates the TPM during the system startup.
5. When the TPM update is finished, the system auto reboots to take effect.
Updating the BIOS from DOS with UEFI boot mode enabled (Non-Windows users, Load Legacy Option Disabled)
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system, then go to BIOS Setup by pressing F2 and go to General > Boot Sequence > Boot List Option.
3. Change UEFI to Legacy of Boot List Option.
4. Click Apply, click Exit to save changes and reboot system.
5. Press F12, then Select USB Storage Device and Boot to DOS prompt.
6. Run the file by typing copied file name where the executable file is located.
7. When the TPM update is finished, the system auto reboots to take effect.
8. Go to BIOS Setup by pressing F2 and go to General > Boot Sequence > Boot List Option.
9. Change Legacy to UEFI Boot Option.
10. Click Apply, click Exit to save changes and reboot system.
Note 2 : Before updating the BIOS, ensure that you suspend BitLocker encryption on a BitLocker-enabled system. If it is not enabled on your system, you can ignore this step. For information about how to disable BitLocker, see How to Enable or Disable BitLocker with TPM in Windows at support.dell.com.
Note 3: The TPM must be ON and Enabled in BIOS Setup, and the TPM must not be owned. If the TPM is owned, go to BIOS Setup and clear the TPM before proceeding. You may need to run TPM.msc to reinitiate the TPM under Windows operating system.
Note 4: When the TPM ownership is cleared, some operating system will automatically take ownership of the TPM on the next boot (TPM AutoProvisioning). This feature needs to be disabled in the operating system to proceed with the update.
Dell TPM Update Utility for Windows/DOS
Download
1. Click Download File.
2. When the File Download window is displayed, click Save to save the file to your hard drive.
Clear the TPM (See Notes 2, 3 and 4)
1. Before running the TPM update utility, clear the TPM Owner.
Disable TPM Auto Provisioning in Windows (See Note 4)
1. Boot to Windows
2. Launch the PowerShell Command window in Administrator mode
3. At the Powershell command prompt, start the command:
> Disable-TpmAutoProvisioning
4. Confirm the following results:
- AutoProvisioning: Disabled
5. Reboot the system, to BIOS Setup by pressing F2.
6. Navigate to Security > TPM 1.2/2.0 Security.
7. Click the Clear checkbox and select Yes at the prompt to clear the TPM settings. (You can skip it if the item is grayed out)
8. Click Exit to save changes.
9. Reboot system to Windows.
10. Confirm the TPM is not owned. The TPM should no longer be automatically provisioned by Windows.
11. When the TPM update is finished, launch the PowerShell command in Administrator mode to re-enable the auto provisioning.
> Enable-TpmAutoProvisioning
12. Confirm the following results:
- AutoProvisioning: Enabled
Updating the TPM update utility from Windows environment
1. Browse to the location where you downloaded the file and double-click the new file.
2. Windows System auto restarts and updates the TPM during the system startup.
3. When the TPM update is finished, the system auto reboots to take effect.
Updating the TPM update utility from DOS environment, with Legacy Boot mode (Non-Windows users)
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system, then Press F12 key and Select USB Storage Device and Boot to DOS prompt.
3. Run the file by typing copied file name where the executable file is located.
4. DOS system auto restarts and updates the TPM during the system startup.
5. When the TPM update is finished, the system auto reboots to take effect.
Updating the BIOS from DOS with UEFI boot mode enabled (Non-Windows users, Load Legacy Option Disabled)
1. Copy the downloaded file to a bootable DOS USB drive.
2. Power on the system, then go to BIOS Setup by pressing F2 and go to General > Boot Sequence > Boot List Option.
3. Change UEFI to Legacy of Boot List Option.
4. Click Apply, click Exit to save changes and reboot system.
5. Press F12, then Select USB Storage Device and Boot to DOS prompt.
6. Run the file by typing copied file name where the executable file is located.
7. When the TPM update is finished, the system auto reboots to take effect.
8. Go to BIOS Setup by pressing F2 and go to General > Boot Sequence > Boot List Option.
9. Change Legacy to UEFI Boot Option.
10. Click Apply, click Exit to save changes and reboot system.
Illesztőprogramokkal kapcsolatos súgó és oktatóanyagok
További letöltésekért lépjen a következő oldalra: Illesztőprogramok és letöltések. Az ezen az oldalon található információk használatával kapcsolatban látogasson el az illesztőprogramokkal kapcsolatos súgó és oktatóanyagok oldalára.