Need TPM Support?
For additional helpful information, please refer to our Knowledge Base. View article.Dell TPM 2.0 Firmware Update Utility
Újraindítás szükséges AUTOMATIKUSAN TELEPÍTETT Ez a fájl automatikusan települt egy korábbi frissítés részeként. Ha bármilyen problémát tapasztal, manuálisan letöltheti és újratelepítheti.Lehet, hogy az oldal tartalma gépi fordítás útján lett fordítva. Visszajelzés küldéséhez töltse ki az oldal alján található űrlapot.
This package provides Dell TPM 2.0 Update Firmware and is supported on Dell Latitude/OptiPlex/Precision/XPS series running the following Operating Systems: Windows 7-32bit, Windows 8.1-32bit & Windows 10-32bit
Ajánlott
Kompatibilitás ellenőrzése
Kérjük, adja meg a termék adatait a rendszeréhez tartozó legfrissebb illesztőprograminformációk megtekintéséhez.Adja meg Dell-szervizcímkéjét vagy -modelljét
Szeretné kikeresni termékét? Adjon meg egy termékazonosítót. Mutasd meg, hogyan!
This driver is not compatible
This driver is not applicable for the selected product. Choose another product to re-enter your product details for this driver or visit the Product Support page to view all drivers for a different product.
Az automatikus ellenőrzés használatához jelentkezzen be a Windowsba rendszergazdaként. Ha már bejelentkezett rendszergazdaként, és látja ezt az üzenetet, kérjük, indítsa újra a számítógépet. A rendszert az IT-rendszergazda kezeli, és előfordulhat, hogy a funkciók köre korlátozott.
További frissítések. A SupportAssist segítségével megtalálhatja az eszközéhez elérhető legújabb illesztőprogram-frissítéseket.
Fixes & Enhancements
Fixes
- Fixed issue which TPM may become unavailable under Windows because of slow response on start up
- Fixed issue which TPM may become unavailable under Windows after upgrade from version 1.3.0.1 to 1.3.1.0
- Fixed issue which TPM may become unavailable under Windows intermittently in a very rare case, under stress test
Enhancements
- Compatibility improvement for Windows 10 Creators Update
További információ- Fixed issue which TPM may become unavailable under Windows because of slow response on start up
- Fixed issue which TPM may become unavailable under Windows after upgrade from version 1.3.0.1 to 1.3.1.0
- Fixed issue which TPM may become unavailable under Windows intermittently in a very rare case, under stress test
Enhancements
- Compatibility improvement for Windows 10 Creators Update
Verziószám
1.3.2.8, A02
Kibocsátás dátuma
21 márc. 2017
Letöltés típusa
Firmware
Kategória
Biztonság
Fontosság
RecommendedA Dell Technologies azt javasolja, hogy a frissítést a következő ütemezett frissítési ciklusban telepítse. A frissítés változásokat tartalmaz a rendszer megfelelő állapotának fenntartása érdekében. Biztosítja, hogy a rendszerszoftver naprakész és kompatibilis maradjon más rendszermodulokkal (firmware, BIOS, illesztőprogramok és szoftverek), és más új funkciókat is tartalmazhat.
Elérhető formátumok
Fájlformátum: CPG BIOS Executable for Windows/DOS
Fájlnév: DellTpm2.0_Fw1.3.2.8_V1.exe
Fájlméret: 594.05 KB
Ez egy nagy fájl. A kapcsolat sebességétől függően a letöltés eltarthat egy ideig.
Formátum leírása:
This file format consists of a BIOS executable file. The Universal (Windows/MS DOS) format can be used to install from any Windows or MS DOS environment.
A letöltés integritásának biztosítása érdekében ellenőrizze az ellenőrző összeg értékét.
MD5:
912cff151665593e42316a467957b794
SHA1:
013ee12772d594e8fb8b3f181e0eae76d6deb76d
SHA-256:
123a3153fb903c4497868fbfaeb49c651c53a87c3b48dec259b26ddb90aa42b2
A letöltéssel Ön elfogadja a Dell szoftverlicenc-szerződés feltételeit.
Támogatott operációs rendszerek
Windows Server 2012
Windows Server 2012 R2
Windows 7 (32 bites)
Windows 8 (32 bites)
Windows 8.1 (32 bites)
Windows Server 2008 R2
Windows Server 2016
Windows 10 (32 bites)
A következőre vonatkozik:
Dell TPM Firmware Update
Telepítési utasítások
Installation instructions
Dell TPM Update Utility for Windows/DOS
Download
1. Click "Download File", to download the file.
2. When the File Download window appears, click Save to save the file to your hard drive.
Clear the TPM (See Notes 2, 3 and 4)
1. Before running the TPM update utility, clear the TPM Owner.
Disable TPM Auto Provisioning in Windows (See Note 4)
1. Boot to Windows
2. Launch the PowerShell Command window in Administrator mode
3. At the Powershell command prompt, execute the command:
> Disable-TpmAutoProvisioning
4. Confirm the following results:
- AutoProvisioning : Disabled
5. Reboot the system, to BIOS Setup by pressing F2.
6. Navigate to "Security > TPM 1.2/2.0 Security".
7. Click the "Clear" checkbox and select "Yes" at the prompt to clear the TPM settings. (You can skip it if the item is grayed out)
8. Click "Exit" to save changes.
9. Reboot system to Windows.
10. Confirm the TPM is not owned. The TPM should no longer be automatically provisioned by Windows.
11. When the TPM update is finished, launch the PowerShell command in Administrator mode to re-enable the auto provisioning.
> Enable-TpmAutoProvisioning
12. Confirm the following results:
- AutoProvisioning : Enabled
Run the TPM update utility from Windows environment
1. Browse to the location where you downloaded the file and double-click the new file.
2. Windows System will auto restart and update the TPM during the system startup.
3. When the TPM update is finished, the system will auto reboot to take effect.
Run the TPM update utility from DOS environment, if Legacy Boot mode (Non-Windows users)
1. Copy the downloaded file to a bootable DOS USB key.
2. Power on the system, then Press F12 key and Select "USB Storage Device" and Boot to DOS prompt.
3. Run the file by typing copied file name where the executable is located.
4. DOS system will auto restart and update the TPM during the system startup.
5. When the TPM update is finished, the system will auto reboot to take effect.
Run the BIOS update utility from DOS environment if UEFI Boot Mode (Non-Windows users)
1. Copy the downloaded file to a bootable DOS USB key.
2. Power on the system, then go to BIOS Setup by pressing F2 and go to "General > Boot Sequence > Boot List Option".
3. Change "UEFI" to "Legacy" of Boot List Option.
4. Click "Apply", "Exit" to save changes and reboot system.
5. Press F12, then Select "USB Storage Device" and Boot to DOS prompt.
6. Run the file by typing copied file name where the executable is located.
7. When the TPM update is finished, the system will auto reboot to take effect.
8. Go to BIOS Setup by pressing F2 and go to "General > Boot Sequence > Boot List Option".
9. Change "Legacy" to "UEFI" Boot Option.
10. Click "Apply", "Exit" to save changes and reboot system.
--------------------------------------------------------------------------------
Note 1: You will need to provide a bootable DOS USB key. This executable file does not create the DOS system files.
Note 2: If BitLocker is enabled on your system, please make sure you suspend BitLocker encryption before updating TPM on a BitLocker enabled system.
Note 3: The TPM must be ON and Enabled in BIOS Setup, and the TPM must not be owned. If the TPM is owned, go to BIOS Setup and clear the TPM before proceeding. You may need to run TPM.msc to re-initial the TPM under Windows OS.
Note 4: When the TPM ownership is cleared, some operating system will automatically take ownership of the TPM on the next boot (TPM AutoProvisioning). This feature will need to be disabled in the OS to proceed with the update.
Dell TPM Update Utility for Windows/DOS
Download
1. Click "Download File", to download the file.
2. When the File Download window appears, click Save to save the file to your hard drive.
Clear the TPM (See Notes 2, 3 and 4)
1. Before running the TPM update utility, clear the TPM Owner.
Disable TPM Auto Provisioning in Windows (See Note 4)
1. Boot to Windows
2. Launch the PowerShell Command window in Administrator mode
3. At the Powershell command prompt, execute the command:
> Disable-TpmAutoProvisioning
4. Confirm the following results:
- AutoProvisioning : Disabled
5. Reboot the system, to BIOS Setup by pressing F2.
6. Navigate to "Security > TPM 1.2/2.0 Security".
7. Click the "Clear" checkbox and select "Yes" at the prompt to clear the TPM settings. (You can skip it if the item is grayed out)
8. Click "Exit" to save changes.
9. Reboot system to Windows.
10. Confirm the TPM is not owned. The TPM should no longer be automatically provisioned by Windows.
11. When the TPM update is finished, launch the PowerShell command in Administrator mode to re-enable the auto provisioning.
> Enable-TpmAutoProvisioning
12. Confirm the following results:
- AutoProvisioning : Enabled
Run the TPM update utility from Windows environment
1. Browse to the location where you downloaded the file and double-click the new file.
2. Windows System will auto restart and update the TPM during the system startup.
3. When the TPM update is finished, the system will auto reboot to take effect.
Run the TPM update utility from DOS environment, if Legacy Boot mode (Non-Windows users)
1. Copy the downloaded file to a bootable DOS USB key.
2. Power on the system, then Press F12 key and Select "USB Storage Device" and Boot to DOS prompt.
3. Run the file by typing copied file name where the executable is located.
4. DOS system will auto restart and update the TPM during the system startup.
5. When the TPM update is finished, the system will auto reboot to take effect.
Run the BIOS update utility from DOS environment if UEFI Boot Mode (Non-Windows users)
1. Copy the downloaded file to a bootable DOS USB key.
2. Power on the system, then go to BIOS Setup by pressing F2 and go to "General > Boot Sequence > Boot List Option".
3. Change "UEFI" to "Legacy" of Boot List Option.
4. Click "Apply", "Exit" to save changes and reboot system.
5. Press F12, then Select "USB Storage Device" and Boot to DOS prompt.
6. Run the file by typing copied file name where the executable is located.
7. When the TPM update is finished, the system will auto reboot to take effect.
8. Go to BIOS Setup by pressing F2 and go to "General > Boot Sequence > Boot List Option".
9. Change "Legacy" to "UEFI" Boot Option.
10. Click "Apply", "Exit" to save changes and reboot system.
--------------------------------------------------------------------------------
Note 1: You will need to provide a bootable DOS USB key. This executable file does not create the DOS system files.
Note 2: If BitLocker is enabled on your system, please make sure you suspend BitLocker encryption before updating TPM on a BitLocker enabled system.
Note 3: The TPM must be ON and Enabled in BIOS Setup, and the TPM must not be owned. If the TPM is owned, go to BIOS Setup and clear the TPM before proceeding. You may need to run TPM.msc to re-initial the TPM under Windows OS.
Note 4: When the TPM ownership is cleared, some operating system will automatically take ownership of the TPM on the next boot (TPM AutoProvisioning). This feature will need to be disabled in the OS to proceed with the update.
Illesztőprogramokkal kapcsolatos súgó és oktatóanyagok
További letöltésekért lépjen a következő oldalra: Illesztőprogramok és letöltések. Az ezen az oldalon található információk használatával kapcsolatban látogasson el az illesztőprogramokkal kapcsolatos súgó és oktatóanyagok oldalára.