Dell SAS Hard Drive Firmware Utility, SATA Hard Drive Firmware Utility, v.Seagate SAS, A00
AUTO-INSTALLATIONCe fichier a été automatiquement installé dans le cadre d’une mise à jour récente. Si vous rencontrez des problèmes, vous pouvez le télécharger et le réinstaller manuellement.
Le contenu de cette page a peut-être été traduit automatiquement. Pour faire part de vos commentaires, remplissez le formulaire au bas de la page.
Ce fichier a été automatiquement installé dans le cadre d’une mise à jour récente. Si vous rencontrez des problèmes, vous pouvez le télécharger et le réinstaller manuellement.
Seagate drives not seen during SMTD installation or after adding additional drives online in Linux. This is a special release targeted only for 5 Seagate SAS drives listed in the Fixes and Enhancements section.
R211868 is intended for all other firmware updates.
Recommandé
Trouver le meilleur téléchargement pour votre système
Saisissez les détails de votre produit pour afficher les dernières informations sur le pilote de votre système.
Rechercher dans le support
Saisir votre modèle ou numéro de série Dell
Vous souhaitez rechercher votre produit ? Saisissez un identifiant de produit.Comment faire
Ce pilote ne s’applique pas au produit sélectionné. Choisissez un autre produit pour saisir de nouveau les détails de votre produit pour ce pilote ou rendez-vous sur la page du support produit pour afficher tous les pilotes d’un autre produit.
Connectez-vous à Windows en tant qu’administrateur pour utiliser les fonctionnalités d’analyse automatique. Si vous êtes déjà connecté en tant qu’administrateur et que vous voyez ce message, redémarrez.Votre système est géré par votre administrateur IT et peut avoir des fonctionnalités limitées.
Trouver d’autres mises à jour. Utilisez SupportAssist pour trouver toutes les dernières mises à jour de pilotes disponibles pour votre appareil.
Correctifs et améliorations
Several Seagate drives shipped from Dell factories between February 2nd and February 20th may experience the following symptoms: A) During an install from System Management Tool and Documentation DVD: 1. If there is no RAID config from ctrl-r and the DVD is booted it will display a blank white screen where there should be array configuration setup. 2. If there is a RAID config from ctrl-r already present on the drives, it will boot to the SMTD DVD but skip the RAID config screen. The menu item for RAID config in the left window will not appear in the action list. Install can be completed using this method.
B) Enclosure or server hard drives are being configured or added in an existing Linux install: The drives my not be seen in the Linux browser that is using Open Manage Storage Management to configure the drives. Or, the Vendor ID for the disk drive may appear with garbled characters.
The FW version on the drive label will represent the correct firmware version; however, a later version was flashed to the drive in the factory.
Dell Technologies recommande d’effectuer cette mise à jour au cours du prochain cycle de mise à jour planifié. La mise à jour contient des modifications permettant de maintenir l’intégrité globale du système. Elle garantit que le logiciel du système reste à jour et compatible avec d’autres modules système (firmware, BIOS, pilotes et logiciels) et peut inclure d’autres nouvelles fonctionnalités.
Ce fichier est volumineux. En fonction de la vitesse de votre connexion, le téléchargement peut prendre un certain temps.
Description du format:
Ce fichier contient un ensemble de fichiers compressés (ou zippés). Téléchargez le fichier vers un dossier de votre disque dur, puis exécutez-le (double-clic) pour décompresser les fichiers. Suivez les instructions pour terminer l’installation.
This release is intended for use on drives attached to SAS/ PERC controllers and MD1000 Enclosures.
Please note: Only Dell Branded SAS/SCSI and PERC controllers are supported. Embedded SATA controllers are not supported.
On drives attached to PERC5/PERC6 controllers, the first drive to be updated requires a 5 minute delay before firmware flash to begin. Do not power cycle or reboot your system while the update is in progress.
1. Click the "Download Now" link to download the file. 2. When the File Download window appears, click "Save" to save the file to your hard drive.
Installation
1. Browse to the location where you downloaded the file and double-click the new file. 2. Read over the release information presented in the dialog window. 3. Download and install any prerequisites identified in the dialog window before proceeding. 4. Click the Install button. 5. Follow the remaining prompts to perform the update.
Detailed Instructions
1) Click Download now. The File Download window appears.
2) Click the Save button. The Save As window appears.
3) Select Desktop using the drop-down menu to the right of Save in.
4) Click the Save button. A progress meter moves as the download is completed.
5) If necessary, click X in the upper right-hand corner of the Download Progress Window to close it upon completion.
6) Double click the Icon on your desktop for the newly saved file.