Genstart er nødvendigAUTOMATISK INSTALLERETDenne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.
Indholdet på denne side er muligvis blevet oversat automatisk. Udfyld formularen nederst på siden for at give feedback.
Denne fil blev automatisk installeret som en del af en nylig opdatering. Hvis du oplever problemer, kan du downloade og geninstallere manuelt.
This package provides firmware version 6.3.1-0003 for the Dell PERC6/i Adapter
Anbefalet
Tjek kompatibilitet
Indtast produktoplysningerne for at få vist de seneste driveroplysninger for dit system
Indtast din Dell-servicekode eller -model
Vil du søge efter dit produkt? Indtast et produkt-id.Vis mig hvordan
Søgningen gav ingen resultater.Vi kunne ikke finde nogen match til din søgning. Rediger din søgning for at indtaste en servicekode (B959FS3) eller model (Latitude 5540), og prøv igen.
Denne driver er ikke kompatibel
Denne driver er ikke relevant for det valgte produkt. Vælg et andet produkt for at indtaste dine produktoplysninger for denne driver igen, eller gå til siden Produktsupport for at se alle drivere til et andet produkt.
Log på Windows som administrator for at bruge automatisk scanning. Hvis du allerede er logget på som administrator og får vist denne meddelelse, skal du genstarte enheden.Dit system administreres af din it-administrator, og funktionaliteten kan være begrænset.
Find flere opdateringer. Brug SupportAssist til at finde alle de seneste driveropdateringer til din enhed.
Programrettelser og forbedringer
Fixes: - Fixes an issue where the Perc battery does not always charge up properly, causing Virtual Disks changing from Write Back to Write Through.
Enhancements: - Removes system events that relate to partial Patrol completion on physical drives.
Dell Technologies anbefaler, at denne opdatering installeres under den næste planlagte opdateringscyklus. Opdateringen indeholder ændringer, der skal opretholde systemets generelle tilstand. Den sørger for, at systemsoftwaren forbliver opdateret og kompatibel med andre systemmoduler (firmware, BIOS, drivere og software) og kan indeholde andre nye funktioner.
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
Dell Update Packages (DUP) i Microsoft Windows 32-bit-format er udviklet til at køre på Microsoft Windows 64-bit-operativsystemer. Dell Update Packages (DUP) i Microsoft Windows 64-bit-format kan kun køre på Microsoft Windows 64-bit-operativsystemer. Når du vælger en driveropdatering, skal du sørge for at vælge den udgave, der passer til dit operativsystem.
Kontrollér kontrolsumværdien for at sikre overførslens integritet.
MD5:
b157de99a0f8acbc2436da9a878ad7f8
SHA1:
0af0351f951bfdac5f080d2d1d72ebb4b086e9f2
SHA-256:
Ikke tilgængelig
Filformat:ZipPack-ekstern
Filnavn:DELL_PERC-6-I-ADAPTER_A14_R313334.exe
Filstørrelse:1.9 MB
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
Denne fil indeholder komprimerede (eller ZIP) filer. Hent filen til en mappe på din harddisk, og kør den derefter (dobbeltklik) for at udpakke filerne. Følg instruktionerne for at fuldføre installationen.
Dette er en stor fil. Det kan tage et stykke tid at downloade den, afhængigt af din downloadhastighed.
Formatbeskrivelse:
Dell Update Packages til Linux kan bruges som et selvstændigt program der sikrer, at specifikke valideringskriterier opfyldes, før opdateringen anvendes. Bemærk: Opdateringspakker til Linux er open-source. Se Vigtigt-filen Dell Update Packages til Linux for at få flere oplysninger.
1. When viewing SATA physical disk properties from Ctrl-R or other management applications, the Vendor Identification will be translated as "ATA" followed by blanks.
2. If all physical disks making up a virtual disk are removed from the system or enclosure, the RAID controller will delete the virtual disk. If the disks are later re-inserted, they will be marked foreign and can be imported using a management application.
3. If a virtual disk is configured with write-back cache enabled and some or all of its physical disks are removed from the system or enclosure, the RAID controller will preserve the virtual disk's write cache. The controller will flush the preserved cache when the physical disks are replaced and the foreign configuration is imported. Any attempt to update controller firmware will be blocked when cache is preserved for a virtual disk.
4. Physical disks determined to contain a foreign configuration are not available for configuration as a new dedicated or global hot spare, or as a member of a new virtual disk. The foreign configuration must be imported or cleared from the physical disk before it may be used as a hot spare or member of a virtual disk. Physical disks with a foreign configuration will not appear on the Create New VD screen in Ctrl-R.
5. Prior to performing a virtual disk migration to another system, the source system must be powered off before removal of the physical disks to preserve the correct virtual disk state. This is not required for the target system and the physical disks may be inserted while the system is powered on or off.
6. The controller restricts the importing of virtual disks that are undergoing RAID Level Migration or Capacity Expansion. Do not interrupt virtual disks that are performing either of these operations because it will disable the ability to import the virtual disk and the data will be unavailable. Dell recommends that the user perform a data backup before starting these operations.
7. EMM changes or drive migrations are not supported during a Capacity Expansion or Raid Level Migration. This may cause the VDs to go offline. Dell recommends the user to perform a data backup before starting these operations.
8. This version of firmware will not ensure complete compatibility with an older version of management applications. OpenManage 5.5 or greater is recommended.
9. It is recommended that the customer upgrade the management application and device driver to the latest version available from Dell at the time of installation of this firmware.
10. Important Information for Update Packages for Microsoft Windows
a. Do not run other applications while executing Dell Update Packages. b. Do not run storage controller update packages if the controller is in use by other applications. The firmware upgrade may fail if any of the RAID controllers in the system are performing I/O background tasks (consistency checks, background initializations, rebuilds, or reconstructions). Allow the background tasks to complete before attempting to upgrade the firmware. Patrol Read tasks will not affect firmware upgrades.
11. Important Information for Update Packages for Linux
a. Do not run other applications while executing Dell Update Packages. b. If the following error occurs, "Error while loading shared libraries: libstdc++.so.5: cannot open shared object file: No such file or directory", you must install the compatibility libraries. These libraries can be found on the installation media or online. To install the compatibility libraries, use the following commands: "rpm -ih compat-libstdc++-33-3.2.3.-*.i386.rpm" for RHEL 4 or 5 "rpm -ih compat-libstdc++-5.0.7-*.x86_64.rpm" for SLES 10 c. When Update Packages stop abruptly due to a power outage or abnormal termination, perform the following steps: - Remove the lock file. - Type the following command: rm -f /var/lock/.spsetup - Run the Update Package again to reapply the update. d. Do not ru
NOTE: This initial section of the Installation Instructions applies only to configurations with (greater than) 2TB SEDs.
1. Update the firmware version to this version using preferred method below (Zip Pack, Windows DUP, Linux DUP). 2. Reboot for the new FW take effect 3. Un-assign any (greater than) 2TB SED Dedicated or Global Hot Spares in the configuration. Not all configurations have hot spares. 4. Use CTRL-R or OMSS to issue Instant Secure Erase to all un-configured (greater than) 2TB SED drives (all data in these drives will be lost) 5. Re-assign (greater than) 2TB SED Hot Spares.
Zip pack:
Download 1. Click the Download Now link to download the file. 2. When the File Download window appears, click Save to save the file to your hard drive.
Extract Files 1. Browse to the location where you downloaded the file and double-click the new file to unzip the download package 2. Click Continue. 3. Specify the location to unzip the files. 4. Click on the OK button to extract files. After the files are extracted the message all files were successfully unzipped will appear. 5. Click the OK button to exit from the installer.
Installation 1. Copy extracted files to bootable media. 2. Reboot system to bootable media. 3. Execute update.bat to perform flash. 5. After flash is complete, remove bootable media. 4. Reboot system for changes to take effect.
Windows Update Package:
Download 1. Click the "Download Now" link to download the file. 2. When the File Download window appears, click Save to save the file to your hard drive.
Installation 1. Browse to the location where you downloaded the file and double-click the new file. 2. Read over the release information presented in the dialog window. 3. Download and install any prerequisites identified in the dialog window before proceeding. 4. Click the Install button. 5. Follow the remaining prompts to perform the update.
Linux Update Package:
Download 1. Click the Download Now link to download the file. 2. When the File Download window appears, click Save to save the file to your hard drive.
Installation 1. Read over the release information presented by executing the ./FRMW_LX_RXXXXXX.BIN --version command from the shell. 2. Download and install any prerequisites identified in the above step before proceeding. 3. Run the update by executing ./FRMW_LX_RXXXXXX.BIN from the shell. 4. Follow the remaining prompts to perform the update.
GnuPG Signature of Dell Update Package Instructions for FRMW_LX_RXXXXXX.BIN:
Download 1. Click the Download Now link to download the file. 2. When the File Download window appears, click Save to save the file to your hard drive.
Installation 1. Import the Dell public key. (You only need to do this once on your system.) 2. Verify the Dell Update Package by using its signature file, FRMW_LX_RXXXXXX.BIN