How to install and remove the Ultraspeed Duo LowProfile card on Precision 7960 Rack

This video shows how to install and remove the low-profile UltraSpeed Duo card on Precision 7960 Rack.

This video shows how to install and remove the Low Profile UltraSpeed Duo card. Ensure you always use ESD protection when working inside the computer. To begin, insert the system-cover key and turn the key counter-clockwise to unlock the system cover. Then, lift the release latch until the system cover slides back. Now, lift the system cover in an angle to remove it from the computer.

To remove the Cooling fan cage, lift the blue release levers to unlock the cooling fan cage. Then, hold the release levers and left the cooling fan cage from the computer. Now, lift to remove the Air shroud and then the three supports. Loosen the thumb screw of Riser 4. To remove Riser 4, push the release button and hold the edges to lift the riser from the system board. Loosen the three thumb screws on Riser 1.

To remove Riser 1, push the release button and hold the edges to lift the riser from the system board. To remove the Air shroud, press the gripping points and pull the air shroud upwards to lift it out of the computer. To remove Riser 3, push the release button and hold the edges to lift the Riser 3 from the connectors on the system board. To remove Riser 2, push the release button and hold the edges to lift the Riser 2 from the connectors on the system board. Now let’s install the Low Profile UltraSpeed Duo card.

To begin, open the PCIe latch and remove the PCIe filler from the Riser 2. Then, slide the PCIe latch holder and align the graphics card with the notch on the riser. Insert the graphics card into the PCIe slot, then slide the PCIe latch holder, and close the PCIe latch. Now, the Low Profile UltraSpeed Duo card installation process is complete. Note: We will demonstrate the system cover installation process once we show the Low Profile UltraSpeed Duo card removal process.

To remove the Low Profile UltraSpeed Duo card, open the PCIe latch and slide the PCIe latch holder. Now, pull the graphics card from the PCIe slot to remove it from the riser. Then, replace the PCIe filler. Close the PCIe latch. and slide the PCIe latch holder. To install Riser 2, align the holes on the riser with the guides on the system board. Then, push the release button on the riser and while holding the edges lower the riser into its connectors on the system board. To install Riser 3, align the holes on the riser with the guides on the system board. Then, push the release button on the riser and while holding the edges lower the riser into its connectors on the system board. Align the air shroud tabs with the slots in the computer and press it down until the tabs click into place.

To install Riser 1, align the holes on the riser with the guides on the system board. Then, push the release button on the riser and while holding the edges lower the riser into its connectors on the system board. Tighten the three thumb screws of Riser 1 to secure it to the computer. To install Riser 4, align the holes on the riser with the guides on the system board. Push the release button on the riser and while holding the edges lower the riser into its connectors on the system board.

Then, tighten the single thumb screw of Riser 4 to secure it to the computer. Now, install three air shroud supports and then the air shroud cover. Now, hold the blue release levers of the cooling fan cage, align the guide rails with the guides on the computer. Then, lower the cooling fan assembly into its slot on the computer until firmly seated. Lower the blue release levers and press to lock the cooling fan assembly into the computer. To close the system, align the tabs with the guide slots on the computer, and slide the system cover. Close the system cover release latch. Insert the system-cover key into the key slot and turn it clockwise to lock the computer. For more information or support about Precision 7960 Rack, visit Dell.com/Support