Prerequisites
Follow the procedure in Before working inside your computer.
Removing the side cover:
Loosen the two captive screws that secure the side cover to the chassis.
Slide the side cover towards the back of the computer.
Lift the side cover from the chassis.
Removing the 2.5-inch hard drive:
Disconnect the data and power cables from the hard drive.
Remove the screw (#6-32) that secures the hard drive carrier to the chassis.
Remove the four screws (M3x3.5) that secure the hard drive to the hard-drive carrier.
Slide and lift the 2.5-inch hard drive off the hard-drive carrier.
NOTE: Note the orientation or the SATA connector marking on the hard-drive carrier so that you can replace it correctly.
Removing the 3.5-inch hard drive:
Disconnect the data and power cables from the hard drive.
Remove the two screws (6-32) that secure the hard-drive carrier to the chassis.
Slide the hard-drive carrier away from the chassis and lift hard-drive carrier out of the disk-drive cage.
Remove the two screws (6-32) that secure the hard drive to the hard-drive carrier.
Slide and remove the hard drive from the hard-drive carrier.
Removing the disk-drive cage:
If the optical drive is installed, remove the data and power cables from the routing points on the disk-drive cage.
Remove the single (6-32) screw to release the disk-drive cage from the chassis..
Lift the disk-drive and detach it from the mounting points on the chassis.
Rotate the drive-cage and place it on the chassis.
If the optical drive is installed, disconnect the power and data cables from the connectors on the optical drive.
Lift the disk-drive cage away from the computer.
Removing the wireless card:
Remove the (M2x3.5) screw that secures the wireless card bracket to the system board.
Slide and lift the wireless card bracket away from the wireless card.
Disconnect the antenna cables from the wireless card.
Slide and remove the wireless card from the connector on the system board.
Installing the wireless card:
Connect the antenna cables to the wireless card.
The following table provides the antenna-cable color scheme for the wireless card of your computer.
Table 1. Antenna-cable color scheme
CONNECTORS ON THE WIRELESS CARD
ANTENNA-CABLE COLOR
Main (white triangle)
White
Auxiliary (black triangle)
Black
Slide and place the wireless-card bracket on the wireless card.
Align the notch on the wireless card with the tab on the wireless-card slot.
Slide the wireless card at an angle into the wireless-card slot.
Replace the screw (M2x3.5) to secure the wireless card to the system board.
Installing the disk-drive cage:
Place the disk-drive cage upside down on the chassis.
If the optical drive is installed, connect the data and power cable to the connectors on the optical drive.
Hold the disk-drive cage upright and align the mounting points on the disk-drive cage with the slots on the chassis.
Align the screw hole on the cage with the screw hole on the chassis.
Install the single (6-32) screw to secure the disk-drive cage in place.
If the optical drive is installed, route the power and data cables through the routing guide on the disk-drive cage.
Installing the 3.5-inch hard drive:
Slide the hard drive into the hard-drive carrier.
Replace the two screws (6-32) to secure the hard drive to the hard-drive carrier.
Align the tabs on the hard-drive carrier with the slots on the chassis and snap the hard-drive carrier onto the disk-drive cage.
Replace the two screws (6-32) to secure the hard drive carrier on the chassis.
Connect the data and power cables to the connectors on the hard drive.
Installing the 2.5-inch hard drive:
Insert and align the hard drive into the hard-drive carrier.
Replace the four screws (M3x3) that secure the hard drive to the hard-drive carrier.
Align the tabs on the hard-drive carrier with the slots on the chassis and snap the hard-drive carrier into place.
Replace the screw (#6-32) to secure the hard-drive carrier to the chassis.
Connect the data and power cables to the connectors on the hard drive.
Installing the front bezel:
Align the front-cover tabs with the slots on the chassis.
Rotate the front cover towards the chassis and snap it into place.
Installing the side cover:
Align the tabs on the side cover with the slots on the chassis.
Slide the side cover towards the front of the computer.
Tighten the two captive screws to secure the side cover to the chassis.
After working inside your computer:
Replace all screws and ensure that no stray screws remain inside your computer.
Connect any external devices, peripherals, or cables you removed before working on your computer.
Replace any media cards, discs, or any other parts that you removed before working on your computer.
Connect your computer and all attached devices to their electrical outlets.
Turn on your computer.
