Search Results (1.6K)
Conversation Type :
Posts
Published Date :
Lifetime
Category
Community Accepted Solution
Hello Everyone,Switch Model: N2000PFirmware: 6.6.3.17 I am trying to configure dot1x authentication using the Cloud Radius server. The configuration I am applying is as below but the switch is not even sending request to the radius(Public IP).Configuration: 1. Enter global configuration mode and de
Question
•
Networking General
Community Accepted Solution
Hi We have 2 N3248TE-ON switches that we want to stack for redundancy. We understand that with OS10 there is no more stacking between switches and VLT is now used. I have been though instructions to setup VLT for OS10 We want to use the 100Gb DAC interface to connect the switches rather th
Question
•
Networking General
Community Accepted Solution
Official Solution
Hi All, As per title, does "SFP-1000BASE-T" transceiver supports 100Mb speed in S4128F-ON switch?Transceiver Part#(DP/N) : 0XTY28 Thank you
Question
•
Networking General
Community Accepted Solution
Hi, Does soemeone know how to assign aggregation only for specyfic neigbour BGP in OS10. Regards
Question
•
Networking General
Official Solution
My dears, I have a "stack" between two n2048! I used the show process proc-list command. I see a process called "switchdrvr". What is that!? Switch memory is critical now. The switch only has 30% memory available. Is it possible to disable this process?! 1156 switchdrvr &
Question
•
Networking General
Community Accepted Solution
Official Solution
I am looking for in-depth commands for troubleshooting Port-Cannel. The issue is that I have been tasked with making a L2 LAG to switches that are physically separated by 3,000 miles. I fully understand this is unheard of but this is my task. To add to the fun the two links are with d
Question
•
Networking General
Official Solution
Our Dell N4064 Non stacked always had a blue light top left when operating. It would flash red during boot but always come back blue. Today our unit had to be bounced and when it came back up there is no light on the unit did proceed through the boot with no errors via putty. The switch is functioni
Question
•
Networking General
Community Accepted Solution
Dell Switch N3024EP showing blinking red light for PSU2. I replaced 2 different FRU - Power supplies, still blinking red on front of the switch. Connected the power cable to different source, still same result. Connected thru putty, shows PSU2 failed, however FAN 2 result is operating fine. Before r
Question
•
Networking General
Official Solution
Hello Dell Team, Good day. I would like to know what is the end-of-life date for the Dell PowerConnect 2824 switch. Thanks. Best Regards, Raul Sanchez Infrastructure & Cloud Services (ICS)
Question
•
Networking General
Official Solution
Hi, We are looking for a 48 Port switch and wanted some information. dell_emc_networking-s5200_on_spec_sheet.pdf (delltechnologies.com) In the PDF link above, page 3 shows the Features as below. What is not clear is : 1) What does Max 100 GbE Density mean 2) How is Max Density related to number
Question
•
Networking General
Community Accepted Solution
Official Solution
Hi, We have on a customer some switchs Dell S3124F-01-FE-28 (version 9.13(0.3). It's connected with Cisco switchs where I see outbound drop. But on the dell Switchs, I don't see discarded packets on output interface but in the input interfaces: Input Statistics: 4955893560 pac
Question
•
Networking General
Official Solution
Hi, Kindly suggest an MIB supported by the Dell S3048-ON OS version 10.5.2.0
Question
•
Networking General
Official Solution
Hi everyone, We have some Dell Z9264F-ON switches and trying to monitor them by SNMP. We've got some false alarm about fan in a switch like below: We checked physically and those status-8 fans still worked well. In a normal switch, they should be like following: Does anyone have experience about t
Question
•
Networking General
Official Solution
Hi Guys I have deployed two DELL S5248F switches in MCLAG running 4.1.0-Enterprise_Standard. I have a problem with the "session status " been DOWN. Am using the management interface IP address for the "KEEPALIVE PEER LINK". I can ping the switch peer from each other and the peer link ports a
Question
•
Networking General
Official Solution
I have two S5248F-ON switches and two S5448F-ON switches. The S5248F-ON switches have QSFP28-DD ports, and the S5448F-ON switches have QSFP56-DD ports. To establish VLT links, I used DAC-Q56DD-400G-0.5M cables on both pairs of switches. I understand that DAC-Q56DD-400G-0.5M cables are intended fo
Question
•
Networking General
Official Solution
Hello all, we had an issue today that caused OSPF to reset. Wondering what the actual cause was. It appears that the no buffer space available log entries pertain to IPv6 yet the IPv4 OSPF session is the one that reset. A few log entries below. Entire issue lasted exactly 2 minutes and 9 seconds.
Question
•
Networking General
Official Solution
Hi, We are using Dell N3248P-ON, Can you please let me know which is the exact MIB file to use for SNMP V2 and the OID to use for port traffic. Thanks
Question
•
Networking General
Community Accepted Solution
Hi,I am trying to LAG two of the 10 gig ports between an N2024 running OS6 and a S3124 running OS9. I can't seem talk between the two stacks. Maybe I'm getting tripped up by a naming convention change. I have include the port configs for the ports in question. If someone could help me out I'd really
Question
•
Networking General
Community Accepted Solution
Hi All, I just install additional S5248F-ON switch to be in VLT with the existing switch. After the installation, the network monitoring system (Orion) show that the "Cached and shared Memory" of the switch are full. I have searched for documentation pertaining to this issue but am afraid I found k
Question
•
Networking General
Community Accepted Solution
Can I use the SFP+ ports 25 and 26 on a S3124 switch to connect an ME5 iSCSI storage using DAC cables?
Question
•
Networking General