This post is more than 5 years old
40 Posts
0
4033
AIX 5.3 does not see Clariion Luns correclty
AIX HOST CANNOT SEE LUNS
ARRAY:
Clariion CX3-40f
FLARE-Operating-Environment 03.26.040.5.019 Active
Storage Group:
ID18S
Luns assigned:
four luns assigned to the storage group ID18S
Lun 10= Raid 5 (4+1) 500 GB Raid group 21 LUN ID: (0x0a)
Lun 11 = Raid 5 (4+1) 500 GB Raid group 21 LUN ID: (0x0b)
Lun 12 = Raid 5 (4+1) 500 GB Raid group 19 LUN ID: (0x0c)
Lun 13 = Raid 5 (4+1) 255GB Raid group 18 LUN ID: (0x0d)
HOST INFO:
Host Name: ID18S
AIX 5300-10-02-0943
Inquiry utility, Version V7.3-883 (Rev 1.0) (SIL Version V6.5.1.0 (Edit Level 883)
HBA’s:
Id18s/fcs0 20000000C981090C
Id18s/fcs1 20000000C981090D
id18s/fcs2 20000000C9810620
id18s/fcs3 20000000C9810621
EMC Software installed:
[root@id18s:/#] lslpp -l |grep -i emc
EMC.Symmetrix.aix.rte 5.3.0.2 COMMITTED EMC Symmetrix AIX Support
EMC.Symmetrix.fcp.rte 5.3.0.2 COMMITTED EMC Symmetrix FCP Support
EMCpower.base 5.3.0.1 APPLIED PowerPath Base Driver and
EMCpower.consistency_grp 5.3.0.1 APPLIED PowerPath Consistency Group
EMCpower.encryption 5.3.0.1 APPLIED PowerPath Encryption with RSA
EMCpower.migration_enabler
EMCpower.mpx 5.3.0.1 APPLIED PowerPath Multi_Pathing
EMC.Symmetrix.aix.rte 5.3.0.2 COMMITTED EMC Symmetrix AIX Support
EMC.Symmetrix.fcp.rte 5.3.0.2 COMMITTED EMC Symmetrix FCP Support
devices.common.IBM.modemcfg.data
Host is manually registered on the array, settings are:
Clariion Open, Failover Mode 3, Array CommPath enabled.
How the host shows under connectivity status:
20:00:00:00:C9:81:09:0C:10:00:00:00:C9:81:09:0C Fibre B-1 Yes Yes ID18S
20:00:00:00:C9:81:09:0C:10:00:00:00:C9:81:09:0C Fibre A-0 Yes Yes ID18S
20:00:00:00:C9:81:09:0C:10:00:00:00:C9:81:09:0C Fibre B-3 Yes Yes ID18S
20:00:00:00:C9:81:09:0C:10:00:00:00:C9:81:09:0C Fibre A-2 Yes Yes ID18S
20:00:00:00:C9:81:06:20:10:00:00:00:C9:81:06:20 Fibre B-0 Yes Yes ID18S
20:00:00:00:C9:81:06:20:10:00:00:00:C9:81:06:20 Fibre A-1 Yes Yes ID18S
20:00:00:00:C9:81:06:20:10:00:00:00:C9:81:06:20 Fibre B-2 Yes Yes ID18S
20:00:00:00:C9:81:06:20:10:00:00:00:C9:81:06:20 Fibre A-3 Yes Yes ID18S
Troubleshooting done so far:
I completely removed the zones, deleted the storage group and deregistered the host. I had the AIX administrator rescan and ensure that no Clariion luns are presented. I then reactivated the zones and reregistered the host. I confirmed that the LUNZ device was showing up on the host. I then recreated the storage group and presented the four luns to the storage group.
I worked with the system administrator to delete the LUNZ device using Primus article emc111635 run a cfgmgr and then an inq, and the results are below:
/dev/rhdisk29 :DGC :RAID 5 :3033 :0A0000B0 : -----
/dev/rhdisk30 :DGC :RAID 5 :3033 :0B0000B0 : -----
/dev/rhdisk31 :DGC :RAID 5 :3033 :0C0000B8 : -----
/dev/rhdisk37 :DGC :RAID 5 :3033 :0D0000BD : -----
dd_emc
26 Posts
0
October 5th, 2011 16:00
I can see that you have loaded the Symmetrix ODM filesets, but can you also check that you have also loaded the equivalent ones for CLARiiON? Sorry I don't have access to an AIX system to confirm their actual names.
dynamox
2 Intern
2 Intern
•
20.4K Posts
0
October 5th, 2011 13:00
is there a LUN at host id 0 ? If not can you create a 1G device and assign it host id 0.
dynamox
2 Intern
2 Intern
•
20.4K Posts
0
October 5th, 2011 14:00
was lun at host id 0 added after the fact ?
1thumb
40 Posts
0
October 5th, 2011 14:00
Dynamox,
there is a lun at host Id 0. Should I remove the four luns from the storage group, have the admin rescan and remove the dead paths, add in the 1GB lun, and the original four luns?
1thumb
40 Posts
0
October 5th, 2011 14:00
No, before I added the luns to the storage group the only thing showing up on the host was the LUNZ device. I then added the four luns to the storage group and the admin ran cfgmgr. He only saw three DGC devices at that point, so following EMC primus article emc111635 I had the admin remove the lunz device. Once that was done he ran another cfgmgr, and then four devices showed up but this is what they look like after a cfgmgr and an inq on the host
/dev/rhdisk29 :DGC :RAID 5 :3033 :0A0000B0 : -----
/dev/rhdisk30 :DGC :RAID 5 :3033 :0B0000B0 : -----
/dev/rhdisk31 :DGC :RAID 5 :3033 :0C0000B8 : -----
/dev/rhdisk37 :DGC :RAID 5 :3033 :0D0000BD : -----
EMC has just completed analysis of the SP collects and have confirmed that everything on the array is configured coreclty and is functioning properly, they are now analyzing the EMC grabs.
dynamox
2 Intern
2 Intern
•
20.4K Posts
1
October 5th, 2011 14:00
is there powerpath on the system, what does "powermt display dev=all" show ?
1thumb
40 Posts
0
October 6th, 2011 13:00
Thank You all for you help, it turned out to be missing ODM fileset for clariion.