Laptop stuck at BIOS/Dell welcome screen.

UPDATE

So I took out the batteries of the laptops then just plugged them in and they both worked fine, did not freeze at all? Anyone know the problem here? I have had bad batteries installed before and they never froze like that they just didn't read or didn't hold charge. Could it be from sitting there they are so dead or are they just bad?

Hi Ftdsn244,

Welcome to the community.

In this case I would suggest you to release the static power and load BIOS defaults. The issue may be caused by the static power. Following are the steps to release the static power.

Remove the battery as well as the ac adapter from the system. Press and hold down power button pressed for 10 seconds.

Once done, load the BIOS defaults by using the followings steps-

Restart the system and start tapping the F2 key as soon as you see the Dell Logo. Once done. Press the “F9” key on the keyboard and then press the “F10” key.

Let me know of the findings, Glad to be of assistance.

Chiranjeev

Social Outreach Professional

You can reach us at http://en.community.dell.com/

Thanks, I just tried doing both and still the same result. Are you suppose to hear any noises or anything when you hold the power button for 10 seconds releasing the static power?

Hi Ftdsn244,

Thank you for your reply.

In this case I would suggest you to run a test on the hardware by performing the following steps-

1. Shutdown the computer.

2. Press and hold the key, then press and release the power button.

3. Release the key.

The PSA diagnostics sequence begins.

After approximately 2 minutes the system produces a number of alert tones.

After the alert tones, the system produces either a series of low beeps or error codes.

4. Note the sequence of beeps or error codes.

At the same time, I would suggest you try powering on the laptop with one memory chip installed at one time and check if both work fine when installed separately.

Let me know of the findings, Glad to be of assistance.

Chiranjeev

Social Outreach Professional

You can reach us at http://en.community.dell.com/

Well good news. I just let it sit on the charger for awhile just turned it on and it works. Started right up with the battery installed. Battery is saying unknown so I am going to try the battery recalib. to see if that works if not atleast I know nothing is wrong with the laptop. Thanks for the help

Hi Chiranjeevi,

Although FTDSN244's problem was resolved without doing anything techie..

I would need your expertise to help me out of this. Let me explain my problem first.

I have a Dell Latiude E5410, I have the same problem my dell junk is stuck at DELL logo screen. How it happened I will explain the details.

I was trying to run the keyboard diagnostics test for that I made my cd drive as the first boot device n system booted n I started running the test. But the diagnostics cd n laptop model didn't match n the test was stuck. I had no choice but to restart the system.

Solutions I have tried till now are removing RAM, Harddrive, CD ROM, running system on AC Power, on battery, without CMOS battery. I have even tried Shorting the BIOS by joining the CMOS battery circuit but no success.

I tried your solution about Fn key and Power button but nothign happens just the Diagonistics boot Selected comes up. pressing F12 and F2 also doesnt help the texts come up Entering boot setup etc etc but the progress bar is still stuck.

Need some expert help here.

Hi gauravvarshney,

Welcome to the community.

Do you hear any beeps when you turn on your laptop? Also what is the status of the Power button LED when you press the power button?

Let me know of the findings. Glad to be of assistance.

DELL-Chiranjeev S

Social Outreach Professional

You can reach us at http://en.community.dell.com/

To reset the BIOS, unplug the system, remove the battery and hold the power button for 30 seconds.  Then apply power again.

If the system won't power up, and it has a memory module, remove and reinstall that (the base RAM as I recall is soldered to the board).  If that doesn't solve the problem, replace the system board.

Hi EJN63,

Thanks for replying.

I did remove the CMOS battery and did the 30 sec exercise with Power button. But it didnt help.

System powers up but the DELL progress bar is still stuck to 1/3. Not sure how the base RAM works and how it should be reset.

Replacing the system board would cost a zillion so that isn't the option for me.

Hi Chiranjeev,

No there is no beep sound. (if you are thinking there is a problem because of RAM, then I have alreayd checked this by removing the RAMs interchanging and running with only 1 chip)

Power button LED is constant.

What I understand of the problem is, that BIOS is corrupted and thats why it is getting stuck.

Suggest a way to reset the BIOS without getting into the BIOS. (I have tried shorting the BIOS but it didnt work.)

Would need your expert opinion on this.

Thanks.

Gaurav Varshney

The base RAM can't be removed.  You've basically eliminated all the possibilities except for the system board.

Good day all,

Was there any fixed results for this issue?

I have this same issue with a Precision M4600.

When turning on, it get stuck at the BIOS screen.

Please help!!!!

I have a similar problem with a Precision M4600: When I cold-start it or reboot it, the Laptop hangs at the Welcome-Screen. It takes a complete power-cycle (Remove Battery and PSU-Cable, hold down Power-Button for 10 seconds) to get past the welcome-screen. Sometimes several attempts of that procedure. 

Diagnostics-Program shows all components to be healthy (Battery is listed as worn out, but still works for about 1 hour), I have tried different settings of the TPM-Module and disabled the Computrace-Module, as well as trying to boot in both BIOS-Mode and UEFI-Mode - No change. 

Short of a complete disassembly and reassembly of the device, I have done basically everything. BIOS-Battery has about 3V, Graphics-Card has been reseated and cleaned, same goes for the CPU, the RAM, SSD and the optical drive.

Interestingly, the laptop seems to be doing something with an SADA-Device just before freezing. Unfortunately, one of these handy POST-Cards for notebooks doesnt show any useful codes on UEFI-Based notebooks. On mine it just shows A0.

Is this more likely a software-problem, or are these the symptoms of a failing SATA-Controller? I remember reading about prematurely aging and failing chips in Intel Chipsets