Unsolved
This post is more than 5 years old
2 Posts
0
71971
Hinges
My inspiron is cracking at the hinges. Has anyone had this problem before? Is this a recurring problem with the inspirons or dell laptops? What should I do to keep it from cracking any further? Can the hinges be oiled and with what? Is there any warranty that covers this type of problem?
jamesdmo
1 Message
0
June 29th, 2000 22:00
The problem is that the hinges use only two very small screws to hold them together. The torque on them is too much over time, and they strip the threads.
The only solution is to call Dell service and have them replace the hinges.
I am typing this while on hold with a Dell technician who says he has never seen it in two years of phone support. Hard to believe since I have seen numerous postings about this before.
Good luck.
hardyrl
2 Posts
0
June 30th, 2000 11:00
The second was from a different technician who siad that dell could not help and I was on my own to do the reapairs!! The 1st did not say exactly what the fix would be only that a method had been found to fix the cracks and then add some kind of support to the hinges to keep it from happening again. They did say that they thought it was caused by the hinges being either too tight or too loose?
This is an obvious problem in dell laptops, the question is why do some dell technicians have a fix and some dont??
DELL-Rance
298 Posts
0
July 6th, 2000 03:00
If the hinges themselves are cracked due to normal usage (i.e. the system was not dropped or subject to impact) you can contact our Mobile Computing Hotline at 800-822-8965 for Government/Education Accounts, 800-234-1490 for Corporate Accounts, or at 800-247-9252 for Direct accounts. You will be connected to a Latitude/Inspiron Technical Specialist who will help you resolve the issue over the phone or arrange the appropriate service. I apologize for the conflicting information you've received from our technicians. Cracking hinges due to normal usage is covered under your system's warranty.
bobbywmol1
1 Message
0
December 23rd, 2002 03:00
Raj_Inspiron820
1 Message
0
January 15th, 2003 22:00
If anyone has the solution to loose hinges on Inspiron 8200, please post it here too...
thanks
Raj
nickbrow
5 Posts
0
January 21st, 2003 21:00
I've had my Inspiron 8000 since May 2001. I've had the hinges repaired in July 2002, and I'm about to call and have them repaired again. This is the only symptom I had: increasing play in the LCD when opened (between 5 to 10 degrees).
I believe Inspiron 8000, 8100, and 8200 all use the same basic case, so this is what is required to repair your system. The whole plastic panel which holds the LCD must be replaced. The hinges themselves do not come detached from the LCD panel.
It's not a functional problem, but it makes the laptop feel cheap to me...so I get it repaired. It's no problem for me since they repair it for free, but I'd rather they give me high-quality hinges. I still love Dell and would buy another, but this goes to show that nothing is perfect!
Let me know if you have any questions about my experience. I'll be glad to help!
funtoupgrade
937 Posts
0
January 21st, 2003 22:00
As near as I can tell the replies to the original question are addressing two different problems with the hinges. Besides the cracking there seems to be a problem with the screws coming loose and also a problem with the actual ease of movement of the hinges themselves.
If the screws stripped out I would try tapping new 3mm threads into the existing 2.5mm stripped ones. If that did not work then I would try small sheet metal screws to secure the hinge assemblies to the base. I wouldn't buy a new top until none of these remedies worked any more.
Regarding movement of the hinges. Don't ever oil them. I tried this once and shot some WD40 into the hinges. It had the effect of making the hinges so loose you could no longer keep the screen at any desired angle. These hinges depend on the friction of the cast metal and are not designed to have any lubrication in there. If the hinges wear out then I can't think of any remedy other than replacing the top. If they crack before wearing out and you can get it replaced under warranty then so much the better.
The hinges are attached to a large metal piece that forms the strength of the top. The metal piece is held to the plastic top with two screws. One could buy a new top, remove the metal plate with the hinges, and then sell off the nice new plastic top on ebay to somebody who had theirs all scratched up. Probably would fetch ten bucks or so.
Finally, I have discovered that when ordering parts, in most cases, it is cheaper to order parts for the newer models if they will work on your machine. Last time I checked the top assembly for an I8200 was cheaper than that for and I8000 or I8100 yet they are physically the same but with different part numbers.
funtoupgrade
corbetjd
2 Posts
0
March 19th, 2003 00:00
funtoupgrade
937 Posts
0
March 19th, 2003 01:00
Don't really know anything about cracked hinges. It is my observation that the hinges become looser and looser over time from normal use and eventually the lid will not stay in just any position you want it to. When it gets to that point I would replace mine. As far as a "major" problem is concerned about the worst thing that can happen is the hinges break and the lid might not stay up at all. At this point one could still use an exterior monitor until replacement hinges are obtained if not on hand.
funtoupgrade
WolfensteinAR
35 Posts
0
March 19th, 2003 02:00
corbetjd
2 Posts
0
March 19th, 2003 03:00
nickbrow
5 Posts
0
March 20th, 2003 14:00
Message Edited by nickbrow on 03-20-2003 08:38 PM
pursuit
2 Posts
0
March 21st, 2003 00:00
Now the left hinge is going the same route. It's not under warranty anymore, so I'm going to need to do something myself.
Irritating. I'll post again if I learn anything useful.
pursuit
2 Posts
0
March 21st, 2003 01:00
OK, I seem to have fixed my problem.
Using these instructions: I took the screen off and then the bevel (the plastic part that surrounds the screen) off.
After all that, I could see that screw #10 in the picture (except on the left side) was loose. (Very loose.) So I tighened up everything that I could see, put the thing back together, and it feels nice and snug.
*victory dance*
UnInspironed
5 Posts
0
August 21st, 2003 21:00
I live and run a business in the UK.
The right hinge on my UNInspiron broke at the three screws. I called Dell and was put through to India. They were very helpfull
I live and run a business in the UK. I rely on my laptop and can’t run my business without it.
The right hinge on my UNInspiron broke at the three screws. I called Dell and was put through to India. They were very helpful and polite. They actually understood my problem exactly and offered to send me replacement parts.
The only problem is that there is no part number for the hinges so the guys sent me some plastic hinge covers – thanks but that just won’t do the job of a metal hinge.
I called back and was told that the hinge is an integral part of the LCD panel and can’t be supplied separately. I told him that I’d already removed the hinge by myself and it wasn’t integral to the LCD. Dell wanted me to buy the WHOLE LCD panel at several hundred £££s and wait weeks while it was installed.
I searched the web and came across www.techno-mart.co.uk. The guys there told me that they could fit the hinges NEXT MORNING. I paid nearly £200 – at least I could now get back to running my business. Their price was far cheaper than Dell and the service was zillions times better.